What slopes are best for an apartment. What slopes are better to choose for finishing on windows? Reasons why you need to finish the windows in the house

In this article, we propose to talk about what are ways to finish slopes for plastic windows . Consider the pros and cons of this or that method and analyze which method of finishing is better to choose.

Installation of slopes is a complex of construction and finishing works, without which the window will be able to carry the functions prescribed by the manufacturers. Slopes are finished using various technologies that differ in quality, durability and price.

In order to do suitable choice a few tips to keep in mind

• The slope must be reliable and durable;
• Resistance to weather influences - moisture, heat, temperature differences is very important;
• Attention should be paid to the tightness and environmental friendliness of window frames and slopes;
• Sloped windows should successfully cope with the thermal insulation of the room and sound insulation;
• Slopes must have a long service life, commensurate with the window profile, and be resistant to wet cleaning.

Let's look at what slopes are and how they differ:

- a widespread method is suitable for both internal and external slopes in houses of any type. Plaster is the simplest and cheapest option. At low temperature there is a possibility of slope freezing due to the poor heat-insulating properties of the plaster, which leads to the formation of condensate and mold.

+ smooth and strong slopes, can be repainted
— you need to have certain skills in working with plaster, there is a possibility of freezing of the slope

. Drywall is an excellent thermal insulator and a tough material. It costs more than plaster, but cheaper than plastic. However, the window opening after the installation of drywall must be treated with a primer with further painting.

+ you can make the slopes even, without skills, you can repaint
— not very durable, drywall may swell when wet for a long time

Wooden slopes are perfectly combined with wooden windows, both of which are quite expensive and require special care. Only professionals should install wooden slopes, it is extremely difficult, but appearance windows with them becomes simply royal.

+ beautiful appearance, environmentally friendly materials
— you need to have certain skills in working with plaster, high cost

Plastic window slope most corresponds in its characteristics to a plastic window. Plastic slopes are used indoors various types. They have a neat and pleasant appearance, quickly mounted. The main advantage of this solution is that plastic slopes, due to the closed porous structure of the inner layer, have a low heat transfer coefficient. Therefore, at low outdoor temperatures, condensation is excluded on slopes and on adjoining window elements, where the wall section is minimal.

+ decorative properties, moisture resistant
— almost impossible to repair in case of damage, may turn yellow over time

Thanks to the above criteria and additionally having decided on the budget allocated for the installation of windows and slopes, you can choose the best option for finishing windows.

Choosing the right slopes for plastic windows.

Installing slopes is an important step in window installation. Slope - the inner part of the window opening, the place where the window itself is inserted. When you have to change the window, you need to pay attention to the slopes, the higher their quality, the better the overall appearance will be.

When installing PVC windows, the following types of slopes are currently offered:

• drywall;
• plastering;
• plastic.

Without (pigtail) any newest and highest quality window will look unfinished and sloppy. And often they learn about slopes in the process of repairing an apartment or when replacing windows. There is an explanation for the fact that the old slopes stood for a long time without a single crack. old design windows had increased air permeability. It blew from a loose fit and cracks, which created a sparing temperature zone for the slopes. But the modern design of wooden and plastic windows has tightness. Air does not enter the gaps, which simply do not exist, and the slopes are between cold outside and warm inside, that is, on the temperature border, which is expressed quite sharply. When the window is opened for ventilation, cold air enters the heated slope, which causes it to crack. Condensation also plays an important role.

Plaster slopes for plastic windows

The plaster mixture from which the slopes are made does not firmly connect to the PVC frame, and this will sooner or later lead to the slope peeling off. There are no materials in the plaster slope that would have good heat-insulating properties, this leads to hypothermia of the opening in cold weather, the window itself. This causes condensation, both on the slope and on the double-glazed window.

It takes a lot of time to make plaster slopes. According to the technology, the material is applied in layers, and each new layer can be laid only after the previous one has dried. Otherwise, the surface will crack. Plaster, which is applied to concrete or brick, continues the wall. Therefore, the slopes are cold and freeze at the junction with the frame. By the way, look at what is now, the most common technology is oknadena.

Plasterboard slopes

The slopes from which still require good fastening have the same disadvantages. If thin plastic is glued onto a sheet of drywall, the quality will also not be up to par: this is laborious work with insufficient stability of the drywall and unreliability of the adhesive joint also leads to destruction.

Thin plastic sheets are not suitable for finishing, although this is one of the most simple ways finishes. In this case, the window frame is not insulated, and this leads to freezing and condensation, and the method of gluing plastic leads to delamination due to compression / expansion of the material.

PVC plastic slopes

Now on the market building materials you can find panels made of cellular plastic. When warming mineral wool, using a mounting profile, mounting panels on a rail, you can use this material. Here you should choose the highest quality manufacturers. Cheaper panels change color over time, stiffening ribs are visible on the front surface, which in turn leads to a loss in the overall attractiveness of the window, giving the impression of a handicraft finish of a window opening with a well-manufactured window.

Slopes from MDF panels at a cost they are quite cheap than those made of drywall, do not have sufficient moisture resistance and need high-quality fastening.

For single-sided sandwich panels good aesthetic performance, but lacks sufficient rigidity. This is especially undesirable for wide slopes, as the slope will sag.

To date, two-layer sandwich panels and special plastic slopes are produced, which are considered the highest quality and most practical in operation, although they are more expensive than others.

Installation of plastic slopes

In terms of installation, the installation of slopes for PVC windows is the simplest. In addition, plastic, unlike other materials, can withstand deformation to a critical point. If the wooden slope does not withstand seasonal temperature changes and deforms without varnish protection, then the plastic calmly tolerates both moisture and temperature changes. From a decorative point of view, slopes can resemble in texture finishes such as metal, wood. This is achieved by laminating with a special film that imitates these materials. Learn about, which will be very interesting.

Installation of plastic slopes video

Photos from the site:

Every man who was engaged in repairs in the house is aware that you can lay tiles with your own hands, install doors or paint the ceiling yourself and save a decent amount on this, and not give it away as payment to workers.

You may not be able to install a double-glazed window alone, but things are much easier with slopes. If you make calculations, then your savings will be about 25%, and this is a lot. Slopes are a necessary element of installation after installing new windows. Even with professional work traces of damage to the window opening remain, and they must be repaired in order to maintain an aesthetically pleasing appearance. The best season for their installation is summer, since installation work in most cases must also be carried out from the side of the street.

What is better to make slopes on the windows

The use of plaster

The cheapest option to get rid of the untidy and sloppy look of windows is plaster. It should be noted right away that it is best to use this method if you are engaged in a thorough renovation of the apartment and have not yet glued the wallpaper in the room. Otherwise, traces of plaster or putty will remain on the wallpaper and you will have to re-paste them. Think over this moment in advance, save yourself from unnecessary work.

Photos from the site:

In the choice of plaster materials importance has that, outside or inside there will be an installation of slopes for windows. If the humidity in your house exceeds the norm of 30-60% (use a hygrometer to measure this indicator), then it is best for you to use a cement base or special plaster for facades (sold in any hardware stores). Use a gypsum, cement or lime-gypsum base if you are installing slopes from the inside.

If you will use gypsum plaster, then you can do without reinforcement of the upper slope. If you are using another poorly adhered substrate, then it is best to do it on a galvanized mesh, this way you will increase the likelihood that the applied layers will adhere strongly immediately after application.

Use a small spatula when applying. When aligning layers, use the trapezoid rule.

It is important to know

Plaster is not a durable material. Over time, traces of cracks and destruction appear on it both on the upper layer and in the inner ones. Therefore, in a couple of years you will need restoration again.

Tips for finishing slopes with plaster

• Pre-protect the window frame from contamination by covering it with some material
• Nail a couple of strips on different sides to guide them and evenly apply the finished mixture.
• Prepare the plaster according to the instructions and recommendations on the package. Use a bucket partially filled with water at room temperature and a mixing tool on the drill to get a smooth paste.
• Thoroughly clean the window surface from traces of dirt and level the rough surface.
• Apply the plaster in several layers, each of which must first be left to dry completely. In this regard, the finishing time varies from 2 to 3 days.
• The last movements should go in the direction of the light: from the window deep into the room.

The use of drywall

This method is faster and less complicated than the previous one.

All work consists of several stages, which go one after the other sequentially:

1. establishing a framework;
2. laying drywall;
3. priming before putty;
4. putty;
5. priming before painting;
6. painting.

At its core, this material is a gypsum, which is enclosed on both sides between cardboard sheets.

Photos from the site:

How to make a drywall slope yourself:

1. Take a profile corner and cut into segments according to the width and height of the window. Then form a rectangle from these beams and attach along the edge window profile using the required number of euro screws or self-tapping screws. Don't worry about the look, we'll hide them under the drywall a bit later.
2. Pre-calculate all the same parameters we need, then cut out the drywall blank. Fill part of the slope with insulation (mineral wool is suitable). The inner edge of the panel with the cut corner will be attached close to the corner. Glue the other edge with special glue to the slope. Drywall is divided into three types: waterproof, fire resistant and ordinary. Most the best option when choosing a material, moisture-resistant drywall from Knauf or Gyprok is used. When you choose the thickness, please note that the best range is from 9 to 12 millimeters.
3. Use sealant and attach a perforated corner at the junction of the side and top panels. Then seal the formed joint near the window, and carefully putty the entire area of ​​\u200b\u200bthe slope. After sanding, prime it with a deep penetration primer and paint with waterproof PVA paint. Ready!

Use of plastic

The most optimal option today are slopes made of plastic. Why this particular material? The one-piece construction, which is obtained as a result of the work, fits into any interior and looks the most harmonious in comparison with other types of slopes.

Photo from the site: vopros-remont.ru

Advantages of plastic slopes:

• Inexpensive cost;
• Long service life of the material;
• You can choose this color scheme that suits the decor of your room;
• Speed ​​of execution installation work. In 3-4 hours, you can easily cope with the installation;
• Plastic is easy to clean, so it's easy to care for and keep clean.

Photos from the site:

Plastic also has its drawbacks: if you have a hole or a crack in it, you will need to produce complete replacement slope. You should also be aware that this material is very easily affected by temperature, so extremely high thermal effects must be avoided.

After installing the double-glazed window, the mounting foam will harden completely within 36 hours. Once this time has passed, you can safely install window slopes.

When buying plastic slopes, pay special attention to the thickness. The minimum thickness should be 8 millimeters. Next, correlate and calculate all the parameters of the plastic (length, width, height), based on the data of your window opening.

What we need:

• F-band equal to the length of the plastic panel.
• Plastic panel. The parameters are calculated from the height and latitude of the slopes
• Insulation. You can choose any, but mineral wool is most often used.
• Small wooden beam OK. We will mount it on the side and upper sides of the slopes.
• Dowel-nails and screws. You will need them in order to attach the wooden planks, as well as to fix the starting profile.
• Silicone. In order for it to look natural, it is best to choose it according to the color of the panels.

This is interesting

Polyvinyl chloride (PVC) is widely used in many industries: construction, toys, furniture, industrial products, etc. Its advantages in comparison with metal are that it is not subject to corrosion, and in comparison with wood - rotting. Compared to other materials, it is durable and, with careful handling, can serve you for decades.

1. Calculate the parameters of your window and make bars of wood of the appropriate length. Once you secure them on each side, use a drill to drill holes into which you will screw the self-tapping screws.
2. Go out
3. Mark the future holes with a pencil, into which we will then insert the dowel-nails. With the help of a level with two ampoules, it is easiest to set the bar evenly.
4. After marking, we make the necessary holes and insert the plugs of the dowels and fix the bar, once again checking whether everything is exactly on the spirit level.
5. Install the F-shaped (shaped like the Latin letter F) profile on the bar. To do this, use a sawing object (knife, saw, grinder). Cut out also the profile parts for the side slopes. In order for us to get even ends, use a tray for cutting boards, which is called a miter box. We will calculate the length we need by the formula: length plastic slope+ the width of that part of the profile that will cover the slope + 20-30 mm we leave in reserve. Having measured the length that suits us, we cut the desired one.
6. We measure from the lower profile the length corresponding to the distance from one edge of the slope to the other. From the part that remains with us, we cut off the strips intended for winding this profile. Next, we use a stapler (construction) and attach the strip to the bar.
7. We measure the length of the upper strip in exactly the same way as in paragraph 4 and fix it again with construction brackets.
8. We need to accurately calculate the 45 degree angle and cut it off so that we can later use it at the junction of vertical and horizontal stripes.
9. One of the last moments before installing the slopes is the installation of the starting profile. Install it with self-tapping screws to the window profile. Mark up first to avoid bumps. With a pencil, draw lines at an angle that we need.
10. According to our drawn line, again with the help of self-tapping screws, we attach the strip to the profile and correctly cut the ends. As a result, you should get a design, the joints of which are almost perfect for each other, you should not have any difficulty in linking them.
11. We insulate the empty space between the F-shaped and starting profiles with mineral wool and also install the panels.
12. At the end of the work, be sure to go through all the joints and coat them with silicone. Thus, we will kill two birds with one stone: 1) tightness will not allow air to pass through the holes, 2) external attractiveness will be preserved and brought into proper form.

note

If you have never done a slope installation before, then try for the first time to find a person among your friends who will help in mastering this business. So you protect yourself from failure as much as possible, and besides, together you will get the job done much faster.

Video “How to install slopes on plastic windows yourself”

If you nevertheless decide to take on your own and repair the slopes with drywall, plastic or putty, then we advise you to familiarize yourself with this video, in which you can clearly see how to make slopes on the window using improvised means.

After installing plastic windows, slopes are installed. Proper implementation of this measure affects the subsequent thermal insulation of the room. But how to finish the slopes for windows inside? Today, there are many materials, thanks to which you can professionally finish the slopes. Let's look at the slopes of sandwich panels, drywall, and PVC.

See also - do-it-yourself slopes for plastic windows.

Drywall

Many people have an idea about drywall is not entirely correct. They believe that it is a profile structure to which the sheet is attached. However, not many people understand how it can be connected to the window system. Therefore, the question related to how to make slopes on drywall windows with your own hands is very relevant for non-professional builders.

Organizational process

As a rule, slopes are placed immediately after changing window systems, so the surface must already be prepared.

If the place in which the slopes will be located has not been prepared, then it must be processed independently, after removing the remains of the plaster from the surface. After that, the walls must be treated with a primer in order to improve adhesion.

Drywall slopes - fastening

If the layer of plaster is dense and difficult to beat off, then it can not be removed, but only if this does not interfere with installation. And to improve its strength, impregnate the plaster with a layer of primer.

Choosing materials

1. The operating time of an already finished product largely depends on the material that will be selected.
2. Since there is a constant temperature difference and high humidity near the window, then it is better to make slopes from moisture-resistant drywall.
3. The primer is an important component that plays an important role in the installation of slopes. It will also prevent the growth of fungus or mold.
4. Drywall will be attached to the landing plaster. Therefore, it must withstand temperature changes, which will create warm slopes for plastic windows, and have moisture-resistant characteristics.

We take measurements

When installing slopes after installing plastic windows, measurements are very important. Let's look at how to take measurements in more detail.

Slopes for plasterboard windows

1. The first thing to do is to measure the distance from the edge of the wall to the window.
2. Then you need to measure the distance from the wall to the middle of the window that sets the slope angle. Thanks to this, we get legs.
3. Next, you should square the length of each of the sides of the triangle, and then add everything up. The square root is taken from the resulting number. As a result, it will become the value of the width that the future slope should have. The length of the panel is measured with a tape measure.

Remember: it is simply necessary to make such calculations. If this is not done, then as a result you will get visually crooked openings and uneven windows. And to make accurate and quick calculations, use the calculator, so you can easily extract the square root without using special formulas.

Installation

Before mounting the slopes, markup should be made, which should be equal to the distance from the wall to the window. Then it is applied to the frames on which the slope will be located.

After that, according to the instructions of the instructions prescribed on the package, planting gypsum is diluted. The mixture is applied with a spatula to the wall in order to obtain 3.4 points of contact between drywall and wall.

Next, you can proceed with the installation of window slopes made of drywall, which includes gluing the sheet with the help of landing gypsum. At the same time, the edge near the end of the wall must be held tightly, and the edge located at the window is equal to the markup.

Installation of slopes for plasterboard windows

Remember: in the process of adjusting the slopes in the markup, it is better to use a level, thanks to which you can easily follow the curvature of the surface.

Final works

When the putty dries, paint for window slopes will come in handy, which is necessary for additional protection.

PVC panels

For those who are still puzzling over how to repair the slopes after installing plastic windows, we can offer another worthy variation - PVC panels.

The installation of PVC slopes is divided into several stages. Let's consider each stage separately.

Surface preparation

After a day after the installation of the balcony block, you can proceed to the installation of slopes. First, remove excess foam that appears between the profiles at the joints and the wall with a clerical knife. After the plane must be cleaned from the remnants of small litter.

PVC window slopes

Initially, using a tape measure, you should calculate the parameters of the profiles along the visible edge. Moreover, it is necessary to calculate their outer width, as well as find out the distance from the top of the window to the bottom. It should be noted that this process can be facilitated if the frames are completely removed or at least slightly bent the film.

To install pvc slopes for windows, a U-shaped profile is used, suitable in width, it is cut into pieces. For this purpose, special scissors are used for cutting metal sheets. Then the profile elements are fastened at a distance of 20 cm with screws to the outer part of the frame. Identical manipulations should be done with the side and top surfaces.

Lathing installation

To collect the crate, wooden slats (section 2 * 4 cm) are used, which are attached to the side and upper corners of the slope. To fix the slats, dowels are used, the distance between which should be approximately 30 cm. If you want a perfect lattice, let the planer enter, thanks to this tool you can perfectly trim the thickness of the slats. At the end, check their evenness using the building level.

Installation of the upper slope

How is the repair of slopes after installing plastic windows with your own hands? First, you should determine the length of the external slope, and then cut off an element of the required size from the PVC panel. It is better to work with the material using a jigsaw, but at the same time, trimming must be done very carefully. Further, the panel is attached to the upper profile and the crate with self-tapping screws.

Mounting the side panels

Side PVC profile mounted in the same way as the top bar. The space that appears between the wall and the panel is filled mounting foam. For this purpose, the exterior of the product is wetted, and then foam is applied to it. This work continues until all free space not filled with material. A PVC panel is attached next, while you should not forget to monitor their evenness using a level, and also fix them with self-tapping screws. The ratio of slopes and angles is controlled by a tool called bevel.

Slopes for plastic windows

Installing F-profiles

At this stage, the installation of plastic corners is carried out, in which the product of the required size is cut off, and then it is inserted onto the panel along the edges. In those areas where the corners come into contact with the screws, a small incision should be made in the inner side of the corner.

Final stage

At the end, the joints are finished, in which a slope sealant or a profile mixture of a suitable color is used. The composition is applied to the incision of the joint, and then gently pressed. The rest are removed. The sealant will protect the product from dust, moisture, debris.

Sandwich panels

When installing slopes from sandwich panels, builders use 3 main materials:

• foam;
• liquid Nails;
• wooden beams.

Foam installation is the easiest option. However, in this case, it is necessary to purchase sandwich panels with a rigid frame. This process is done like this:

• taking measurements;
• trimming the frame strip;
• frame assembly;
• fixing the frame between the upper slope and the window sill;
• cutting panels;
• inserting panels into the frame.

Foam

First, 2 side slopes are assembled, and at the end - the upper one. Before blowing out the system with foam, it is necessary to measure the slopes with a level, and also place spacers so that the swollen foam cannot displace the frame.

Slopes from sandwich panels

This method can only be implemented if two-layer sandwich panels are used. To improve adhesion, before blowing out the cracks, the wall of the room and the inner plane of the panels should be sprayed with water from a sprayer.

After a day, the foam will harden, then it will need to be trimmed. Next, put on linings that perform a decorative function. Sometimes installers carry out this process immediately, but this is not compatible with the technical rules.

Liquid Nails

They will be appropriate only if the walls are in good condition. Thanks to liquid nails, you can not use the frame, installing it directly on the wall.

This method is suitable for spacious windows, where a lot of plastic will negatively affect their appearance. The process is divided into the following steps:

• measurements;
• trim panel;
• preliminary fitting;
• leveling the surface (plaster, removing old materials);
• panel bonding.

Initially, the outer panel is attached, and the side panels are adjusted to it. But after that, 2 unresolved problems remain:

• seams in adjacent places;
• open end piece.

I close the seams with a simple putty mixture that matches the color or silicone, provided that the plastic is white. Today, more and more often, acrylic paint is used for such work, its texture is similar to PVC coating, so you can create a good appearance.

Slopes from sandwich panels for windows

The end face can be covered with a layer of plaster. And if the windows are located over the entire surface of the wall, then there will be no need to think about how and how to paint the slopes on the windows inside. In this case, the end face is painted with white paint, but here it should be noted that the sandwich panels must have an identical color. You can also just hang wallpaper.

wooden blocks

To reduce foam costs during the installation of difficult, destroyed slopes, wooden slats are used, which are the basis for attaching the frame. The technology of this process is as follows:

• taking measurements;
• cutting beams;
• assembly of a quadrangle, to which planks of sandwich panels are attached using a stapler;
• cutting and subsequent insertion of panels into the base;
• blowing foam;
• after 24 hours, all unnecessary is removed;
• lining installation.

Window slopes made of sandwich panels are particularly resistant to mechanical defects. Give preference to 3-layer panels, because 2-layer ones are not rigid enough. However, this condition is optional.

To complete the installation work front door or windows need to trim the slopes. A door or window slope can be made using plaster, drywall, plastic panels.

The most common option for facing slopes are plastic panels. Since finishing window slopes inside with plastic is a universal solution. It should be noted that this building material is used for indoor and outdoor work.

Benefits of plastic

For facing the slopes of the house, the plaster method was previously used, then drywall, which was widely used for sheathing. But with the advent of PVC windows, plaster and drywall faded into the background. Since finishing the slopes with a plaster method has significant disadvantages. The main disadvantages are:

• If you plaster the slopes yourself, it takes a lot of time.
• With this type of finish, a lot of construction waste occurs.
• Due to shrinkage and temperature changes, cracks may occur on the surface.
• The constituent elements do not form the required adhesion with the plastic, as a result of which the slopes peel off from the window.

Internal window slopes made of plastic

To plaster the window opening well, you should use a perforated corner and beacons. The perforated corner is installed on the outer corners of the slope. To do this, you need to cut off the corner of the required size, putty is applied to the slopes and the perforated corner is pressed. The plaster beacon is installed vertically along the window frame. To do this, cut the lighthouse to the desired size, apply putty along the box and attach the prepared parts. After 40 minutes, you can plaster the slopes.

Such a finishing material as drywall provides an opportunity to make slopes faster and warmer. But even the moisture-resistant version of this material does not withstand temperature changes and the influence of condensate. PVC slopes on windows have a more interesting appearance.

Advantages of plastic slopes

But beauty is not their only advantage, the positive characteristics include:

• The panels are made of the same material as the window frame, therefore, the near-window space P the premises acquires a monolithic structure.
• It is enough just to install a heater. It should be noted that with proper insulation, the occurrence of condensate is impossible.
• Installation of plastic panels practically does not create debris and noise.
• This kind of building material can be used outside and inside, since polyvinyl chloride does not emit harmful substances.
• Insensitive to moisture.
• Duration of use.
• It tolerates temperature fluctuations.
• Ease of operation.
• The building material differs in its excellent pricing policy, therefore, it is available to anyone who plans to install plastic window slopes with their own hands.

The disadvantages of plastic include the impracticability of fragmentary restoration.

Do-it-yourself plastic slopes for windows (video)

The choice of building material

Before you think about how to make plastic slopes yourself, you need to consider possible variations in materials. There are 2 types of plastic panels:

1. Decorative.
2. Sandwich panels.

Decorative slopes can be used:

• For the formation of partitions.
• As a facing building material for balconies.

Necessary tools for finishing window slopes

For all other purposes, preference should be given to sandwich panels. This kind of material differs in that it has 2 protective layers, a facing layer of insulation. Such a structure avoids additional insulation. Key points for choosing panels:

1. Preference should be given to building materials made from virgin plastic. Since the material is correctly selected, it will not change color, and the composition will not cause harm to health.
2. It is better to give the choice to material with a significant cover of plastic. Panels with thin PVC sheeting are not durable. Over time, the plastic peels off the surface.

Finishing window slopes with plastic requires the following materials:

• Profile.
• Self-tapping screws.
• Dowel.
• Wooden slats.
• Gypsum insulation wool.
• Liquid Nails.

Preparatory moments

Removal of the remnants of mounting foam

To make the finishing of window slopes inside with plastic with high quality with your own hands, you need to clean the walls and prepare all the necessary fixtures and building materials. To form slopes, the thickness of the plastic strip should be 8 mm. The width and duration of the plastic should correspond to the size of the opening. Prepare and clean the walls step by step:

1. Remove excess foam.
2. Remove the shipping tape from the window profile.
3. Seal the inside seams.
4. The upper and side sections of the hole should be freed from whitewash and leveled with putty.
5. It is recommended to wipe the prepared area and apply 1-2 coats of primer.

Technologists i formation and installation

After preparing the opening around the circumference, a vapor barrier film should be glued. At the combination points, the sections of the film should be laid with an excess of 5-7 cm and glued along the seam. The tape must be glued so that the edges do not extend beyond the window frame. After that, you can proceed to the formation of slopes using the following instructions:

We fasten the bars with dowels

• Fastening lumber material. For these purposes, wooden slats 15 mm thick and 40 mm wide are taken. It is necessary to trim the rails along the width and height of the outer edge of the opening. You need to fix the rails with dowels around the circumference of the opening. If the walls of the hole are wavy, then it is recommended to place wedges under the planks.
• Take the necessary measurements carefully. It should be understood that all measurements must be taken from the frame, and not from the edge of the special profile.
• Open slopes. The length and width of the walls of the hole should be correctly measured, and attention should be paid to the angle of inclination on each side. On the plate it is necessary to mark the cutting points and cut out the workpieces. The resulting elements should be attached to the wall and check their location and angular fit.
• Special profile mount. A special profile should be attached along the outer edge of the opening with short screws. At the corners, when rallying the bars, the special profile should be fixed so that no gaps form. Installation of slopes begins with the manufacture of edging. This structural component is made from an F-profile. All manipulations should start from the top element. The profile must be cut to the size of the outer opening and sawed down at 45 degree angles. The prepared special profile should be attached to the bar so that it can be covered with plastic, but at the same time, do not block the groove for fixing the slope.

Installation of plastic slopes

• The profile is fixed to the bar with brackets. In a similar way, the remaining segments are mounted. The prepared slope element should be placed in a special profile, pre-coated with sealant. The resulting gap between the plastic and the wall must be sealed with a heater. It should be noted that the layer insulation material should not be excessively massive or have vacuums. The outer edge of the slope must be brought into the groove of the special profile and pressed to align the panel. Next, you should sew up the side slopes, while scrupulously distributing the thermal insulation. If the external walls are insulated, then such manipulations with slopes can be omitted. In such a situation, the gaps between the panels and the base of the slopes should be sealed with mounting foam.
• The final period involves the fastening of decorating corners, which should be glued with glue. The points of contact between the panels must be degreased and all cracks covered with acrylic sealant. Acrylic should be squeezed directly into the gap, mashed and leveled, the resulting excess should be removed with a damp cloth. All manipulations should be done in small areas and wiped gently clean. Since, until the acrylic has hardened, it is quite easy to remove. The section of the opening under the window sill is being plastered.

PVC sheathing

Advice! You can veneer window slopes in another way, which differs significantly from the previous one. This method allows you to sheathe a window slope using any PVC material. It should be noted that this option is used when the mounting seam has a small interval, that is, the distance from the frame to the wall is minimal.

The initial stage should be carried out in stages:

• Cleaning.
• Elimination of defects.
• Applying a primer.

Sheathing slopes should be adhering to the following rules:

1. Remove excess foam, while you need to make sure that the cut is placed flush with the surface of the frame.
2. Facing slopes with plastic plates provides for surface treatment with a primer. Preference should be given to penetrating compounds with the addition of antiseptic components.
3. Fixing rails.
4. An important point is the trimming of the mounting foam. Cutting is done in such a way that a groove is formed for fixing the plastic. Cutting is done in close proximity to the frame to ensure maximum fit of the material.
5. Reveal the details.

Window slopes lined with PVC

After the performed manipulations, a number of actions should be performed:

• Using a jigsaw, you need to cut plastic. As a rule, burrs may remain along the edges, which can be removed with sandpaper.
• Performing pre-assembly. Such manipulation will determine the presence of defects. If double-sided plastic is used for facing slopes, then one side needs to be sanded a little, thereby indicating the wrong side of the material. Carrying out such manipulation promotes better adhesion. Since the fixation of PVC panels is carried out using mounting foam.
• Prepared elements are placed in the right place. They need to be installed in the prepared groove. Using a level, the structure is leveled.
• The outer edge of the part is moved away and spot foam is poured.
• All parts of the structure are attached to each other with masking tape. Fixation is carried out along the circumference of the structure and at the points of joining.

Important! For beginners, the question arises: how long will it take to dry completely? As a rule, it will take a day for a thorough drying. After that, additional finishing measures are performed. It should be remembered that external slopes also require attention.

Quite often, siding is used for such purposes. Working with building materials does not cause any particular difficulties due to the characteristics of the material. But if there are difficulties, then in the vastness of Runet there are many videos and photos from detailed instructions regarding siding installation. The ease of installation work will allow you to make the cladding yourself.

Photo gallery of finished works

The final stage in the design of the window opening is the finishing of the slopes of the windows inside.

This is not only the aesthetic side and completeness of the interior, but also a replacement old plaster, which allows you to make openings more reliable with improved thermal insulation.

If the slopes are made with high quality, their heat and sound insulation properties will only improve. Do not postpone this procedure for later, as this can lead to unpleasant consequences:

• Thermal insulation may be damaged by the action sun rays on building foam, which is usually used to process openings;
• If the foam layer is not treated, it will draw moisture into itself, thereby destroying the structure during the cold period;
• Cracks may appear due to an increase in the volume of foam;
• Drying of the mounting foam leads to the fact that it begins to crumble and gradually loses its thermal insulation properties.

Slopes can be trimmed various materials: laminate, wallpaper, wood, parquet board, cork, decorative plaster. The basis should be chosen in accordance with the design of the room and the material of the window opening itself.

Light finishes require the use of light materials, which cannot be said about heavy types of cladding, such as tiles. Here you should prepare a cement-gypsum base.

Consider the most popular options.

Plastering

This method can be called the classic way of finishing. It will require the following materials and tools:

• Cement;
• Sand;
• Putty starting;
• Finishing putty;
• Water;
• Primer;
• roller;
• Level;
• Water-based paint;
• Dye;
• Sandpaper (fine-grained).

Work should be started after 36 hours so that the foam grabs well on the openings.

The window is cleaned of old plaster, paint, wallpaper and dust. A layer of mortar is applied to the walls, then to the slopes from the bottom up. A solution is prepared from sand, cement, water and the first layer of plaster is applied where a large amount of the mixture is required.

Apply each subsequent layer after the first has completely dried. The thickness of each application should not exceed 7 mm.

After the surface is rubbed with fine-grained sandpaper, you can proceed to painting it. water-based paint, which with the help of a dye can have any color, according to your design.

Can also be wallpapered. The method is good because it is the basis for any type of finish. But there is also a drawback, the sand and cement mortar has an unreliable connection with the PVC frame material, which can lead to cracks.

If we talk about thermal insulation properties, they are weak and will eventually lead to the formation of condensation and mold. In order to prevent this from happening, it is necessary to additionally install a layer of insulating material.

Drywall

Moisture-resistant material is mainly used when finishing slopes inside, as it is resistant to condensation on the window, and is distinguished by thermal and thermal insulation resistance.

Sheets of material are attached to a prepared crate (metal or wood). The surface should be pre-treated with a solution if there are strong potholes.

The collection of the slope begins with the panel located on top, its edge is smeared with glue and inserted into the starting strip. To the wall, you should press the second end of the drywall. Also, this procedure must be carried out with the side panels. Here, the treatment of joints with a neutral sealant should be mandatory.

To prolong the life of the corners, you can use paint corners.

The last step is to use the putty, with acrylic or oil paint applied to it.

Decorative rock

Natural stone is rarely used. There are reasons for this. First, it's heavy. Second, it's expensive. Therefore, an excellent analogue is a decorative stone. They get off the door and window openings and you can do this job on your own.

Decorative plates 2 cm thick are selected. An area is being prepared for fixing artificial stone (plastering). Notches are made on the surface, for more reliable fastening, glue is added and treated with a primer.

Then, after drying, glue is applied to the slab or wall and the stone is fixed. You can also use liquid nails. The work is carried out using the building level.

Laying is carried out in horizontal rows from the bottom up. If necessary, trim the stone.

Plastic, laminate and parquet board

The use of plastic is the most common processing option, as its distinguishing characteristic is durability (15-20 years).

It is convenient to put it for several reasons:

• You can start work on the same day;
• Plastic panels are an additional heat-insulating barrier between the room and the street;
• High moisture resistance;
• The homogeneity of the material of the double-glazed window and the slope allows you to work synchronously with temperature changes;
• Does not fade;
• Washes well, does not sweat;
• Does not need painting;
• Has an attractive look.

Technical features of the material allows you to make slopes various forms- bay windows, arched and round.

This finishing method deserves attention, as it looks original. There is one problem in working with a laminate board, it crumbles. Therefore, you should decide in advance how to hide the corner joints.

Finishing can be started from top to bottom and vice versa. The difference is noticeable only in the direction of the lamella grooves. Fastening is carried out with self-tapping screws, each next lamella closes the groove of the other, due to which the attachment points remain invisible.

The parquet board is quite easy to saw because the base is wood. laminate or parquet board it is allowed to mount on drywall.

Finishing the slopes inside and outside should be done at the same time. Work is carried out at a temperature of 20-25 degrees.

To improve the quality of the slopes, they must be insulated. For an opening finished with plaster, it is better to use paint as the last layer - this will increase its moisture resistance.

Video material on the correct design of the slope surface:

The finish of the window slopes inside can be different, but the developed angle must be maintained so as not to disturb the distribution of light in the room.

Share this article with your friends on social media. networks!

Finishing the slopes of windows inside the apartment

Architects creating their masterpieces great importance attached to the windows as the final stage in the formation of the architectural ensemble. Sizes, shapes and functional purpose changed over time and the requirements of architectural fashion.

The architecture improved, and with it, the windows became the dominant decorative wall motif. Having absorbed a variety of styles inherent in a particular era, the windows have acquired a laconic look and a classic shape. This element of architecture has a decorative character and surprises with functionality.

Plastic windows prevail over their wooden counterparts for a long period. Therefore, finishing the slopes of plastic windows and their installation does not lose its relevance.

Types of materials

More recently, slope plastering has been in vogue. At the same time, the adhesion of plastic and plaster was not very good. Very often, the seams cracked, due to temperature changes, the entire surface of the window cladding cracked. hydro-, heat - and noise insulation was violated. At the same time, plastering is a complex and lengthy process that requires patience and accuracy.

With the help of modern developments, the finishing of the window slopes inside is presented in several forms, which implies a choice based on the positive aspects of the materials.

1. Panelite is a cellular panel made of PVC with an internal filler of expanded polystyrene. It is used at a depth of not more than 25 cm. Docking of this panel at a deeper window opening loses presentability, and also changes color over time. Due to its low weight, finishing windows inside is not much of a hassle. They have increased resistance to mechanical damage.
2. Adhesive plastic is attached with glue. It has a number of disadvantages: peeling as a result of temperature fluctuations, condensation forms during freezing.

Drywall sheets as a finish have good thermal insulation, are environmentally friendly, and can be painted in any color. Disadvantages: at a high level of humidity, cracking and destruction of the integrity of the drywall construction occurs.

Sandwich panels are made of polymer plastic, they are the most reliable option for finishing window openings: providing thermal insulation, color retention, easy maintenance, resistant polymer coating, aesthetic appearance, reliability and durability in operation. At right choice insulation, fire-resistant sandwich panels. Sheet plastic is of high quality, excellent thermal insulation, accurate color match with window frame. The disadvantage is the high cost.

With all the diversity, it is worth taking a responsible approach to the choice of materials, taking into account all of the above factors, before how finish window slopes inside .

How to choose the right slopes for plastic windows, read in our article “Choosing the most “correct” slopes for plastic windows”.

Finishing window openings inside with plastic

High-quality sheathing of window slopes with plastic after installation is completed will save you from many unpleasant consequences. It is designed to ensure the preservation of heat in the room, sound insulation and moisture penetration.

Finishing window slopes inside with plastic has numerous advantages. Defining parameters:

• aesthetic appearance;
• duration during operation provides economic benefits;
• damage-resistant material;
• functionality.

In addition to the main characteristics, it is worth paying attention to the technological qualities of slopes:

• the presence of stiffeners (panelite);
• the content of foamed insulation (sandwich panel) ensures greater preservation of heat in the room;
• prevention of formation of condensate;
• tight;
• correct installation hides defects;
• interior decoration windows looks symmetrical and smooth;
• large color palette;
• a lamination procedure is possible to create a textured structure;
• matte and glossy surface;
• dust repellent surface
• comfort and ease of care;
• ease of installation design.

High-quality finishing of internal slopes of plastic windows serves as a guarantee of durability.

Necessary tools and materials

The interior decoration of plastic windows requires some preparation in terms of acquiring the necessary materials and tools:

• level;
• drill;
• construction knife;
• calculator (for comfort in calculations);
• F-profile;
• stapler;
• mineral wool (installation foam, ponoizol);
• silicone (sealant, liquid plastic);
• staples;
• antifungal agent (primer, fungicide);
• self-tapping screws small size("bugs");
• plastic;
• choppers and slats (plastic, wood);
• masking tape;
• degreasing agent (alcohol, acetone).

Still undecided which profile to choose? Read our review about all brands of plastic windows.

To beautifully decorate the slopes on the windows, read about the various plastic corners on the windows here.

How to do interior window trim

In order to finish the openings. no need to ask for help qualified specialists. The easiest way, which is quite doable, is to decorate the windows with plastic with your own hands. It is enough to follow the rules and gradually revet the window opening.

Buying and preparing everything necessary materials and tools, you can be inspired to start facing window slopes with plastic.

1. Preparation for work:

• carefully cut off the remaining foam that protrudes;
• remove paint and old plaster;
• treat with an anti-fungal agent.

1. Panel cutting:

• make accurate measurements;
• put markings;
• cut at a 45° angle.

1. Installation:

• fix the cut panels around the entire perimeter of the window opening with small self-tapping screws;
• carefully dock at the corners;
• with a slight mismatch, adjust the design;
• observe a gap of 3 cm between the base of the slope and the plastic structure.

1. Filling voids:

• foam for installation (mineral wool, penoizol) fill the perimeter between the old and new slopes;
• foam should not be filled in a continuous line, but at small intervals.

1. F-band installation:

• F-profile corners cut at an angle of 45°;
• to fix the rail, use chopsticks made of wood or plastic;
• on masking tape, attach the profile with grooves to the end part of the plastic panel.

1. Finish:

• degrease the facing seams at the joints;
• fill them with sealant.

As a rule, finishing plastic windows inside takes no more than 3-4 hours, even in the absence of experience.

Reasons why you need to finish the windows in the house

The completeness and accuracy of the window create slopes, both inside the room and from the outside, and also carry a number of functional loads:

1. outdoor:
   • protection against destruction of mounting foam,
   • prevent moisture ingress
   • thermal insulation,
   • maintain sound insulation
   • UV protection.
   • I provide reliable adhesion of the window frame to the opening.

1. internal:

• decorative element,
• protection of waterproofing materials,
• eliminates condensation.

If the slopes are not finished on time from the outside, then the negative consequences will lead to the re-installation of the window block. These are additional expenses and money, and time, and forces.

How to trim the slopes inside the window

Modern glazing technologies imply an attentive attitude to every detail, so questions about how window sills and slopes are designed also do not go unnoticed by the master. Proper repair These structural elements of the window will provide it with a longer service life and prevent the risk of cold air entering the home. Let's talk further about how the window slopes are finished inside, and what materials must be used for this.

The need to finish the slopes inside the window

The relevance of finishing window openings inside and outside the house with sandwich slabs, plaster and so on, as well as the front door decorative stone quite high. The internal factors, the action of which can adversely affect the quality of the window itself and its slopes, include:

• increased humidity indoors;
• the appearance of condensation on the window due to a significant difference in temperature outside the window and inside the house.

External factors that destroy the window and its slopes include:

• precipitation, wind, sunlight;
• sharp drops temperature regime ambient air;
• mold, fungus, harmful insects.

Proper decoration of windows and doors with decorative stone allows you to raise the level of resistance window construction to the influence of the factors described as high as possible. This will ultimately extend the life of windows, improve the appearance of window openings in particular, as well as the facade of the house as a whole. You can see a window with high-quality slopes inside the room in the next photo.

Drywall

Most often, the decoration of slopes indoors and the front door is done using drywall. This is a finishing material with high performance parameters, which allows you to quickly and with a minimum of effort to make the slopes perfectly even and resistant to external influences.

Drywall is lightweight, its installation on vertical surfaces is not particularly difficult. It is beautifully dyed in the actual color shade. In addition, such materials, when properly treated with antiseptic compounds, can prevent the risk of mold and mildew at the junctions of slopes and window frames. Finishing the window with drywall is shown in the following photo.

Material selection

Do not think that you can choose any type of drywall for the design of slopes in the house. The material should be selected taking into account its operational parameters. And they have different types drywall are different, which should be taken into account by the master before materials are purchased and window repairs begin.

Absolutely any window is a source of moisture in the form of condensate, which is formed due to the large difference in temperature in the house and on the street. As a result, the materials with which the slopes will be repaired must certainly be resistant to this factor. So, you need to select only moisture-resistant drywall sheets, on which the presence of condensate will not adversely affect. Otherwise, the repair will retain its functionality, an attractive appearance for only a short period of time. In addition, it is worth using antiseptic compounds to cover the surface of the material, as well as a special paint for its finishing.

Finishing the slopes of plastic windows in the house should always begin with taking measurements, for which you will need to stock up on a measuring tape. The final results of the work of the master largely depend on the quality of this stage of work. If the slope does not fit as tightly as possible to the window frame, there will be a risk of developing such negative consequences as:

• the appearance of mold, fungus outside and inside the room;
• the appearance of microcracks through which frosty air will begin to penetrate into the house in the cold season. Gradually, without adequate measures to eliminate the problem, cracks will grow, and with them the cost of space heating;
• shortening the service life of the window structure, its rapid wear both in terms of quality and aesthetics.

Taking measurements

Slope installation

Finishing slopes with drywall begins with an analysis of the measurements taken. All window settings are transferred to drywall sheets, from which you need to cut pieces that are ideal for the window opening.

drywall cutting process

Installation of such canvases can be carried out on the crate, on the profile, or without them. The choice of technology should be determined by the state of the slopes. Evaluate visually whether they are processed with high quality, as well as what quality the double-glazed window itself has.

Drywall installation is carried out on a special adhesive, if the walls are perfectly even. If not, you will need to first bring them to such a state.

Next, you need to fix the bar on the window profile or frame, which will securely fix the drywall from the side of the double-glazed window. Plasterboard panels are installed on top of the plank, carefully treating the resulting voids with a sealant. Then the design will be devoid of cold bridges.

Removal of excess mounting foam Installation of the slope angle Metal crate Installation of drywall boards Finished drywall slope

PVC panels

No less popular today is the repair of slopes in the house PVC panels on the profile and doors with decorative stone, so that the whole structure acquires a solid appearance. Such repairs, as shown in the photo below, are distinguished by a long service life and retain their properties for a long time.

Plastic panels are selected taking into account the size of the window opening, as well as its technical parameters. Before starting repairs, you will need to prepare the surface of the slopes. Then, PVC parts are cut to the actual size, which will be mounted around the entire perimeter of the window on wooden slats and a profile.

If you want to insulate the house, the space between the wall surface and the panels should be filled with a layer of mineral wool or construction foam. Finishing slopes with PVC panels on the profile is also beneficial because PVC materials have a smooth surface, are produced in different color shades, look harmoniously in the interior of a private house. This allows you to save on finishing painting slopes.

Another attractiveness of this method lies in the fact that all elements of the window structure (window, slope) acquire the same expansion coefficient, which will provide them with a snug fit to each other and prevent the risk of cracks.

The scheme of finishing the slope with PVC panel

Surface preparation

For the installation of plastic plates on a slope, it is necessary to carefully prepare the surfaces. To do this, I carefully cut off the excess mounting foam with a clerical knife, and the surface itself is cleaned of dirt and dust, covered with an antiseptic, primed. Next, you need to install a metal frame from guide profiles.

A hair dryer will help clean the walls of paint.

Guide profile installation

Measure the profile along the outer edge with a construction tape measure, and then its outer width and the distance from the top edge of the window structure to the window sill surface. Take a U-shaped profile of the current width, cut it into segments with metal scissors, according to the measurements of the window. Next, the segments are screwed with an interval of 20 cm using screws along the outer part of the window frame. In the same way, the top, side profiles are mounted.

Metal profile Assembly of the start profile

To organize the crate, you will need wooden slats with a cross section of 20x40 mm, which are attached to the far corner of the slope from above and from the sides with dowels in increments of 30 cm. The crate must have perfect evenness, for which the thickness is trimmed with a planer wooden slats and check the work with a building level.

Panel mounting

Finishing with plastic plates can be easily done by hand. To do this, cut the material with a jigsaw, then fix it on the upper profile and fix it on the crate with self-tapping screws.

The side profile is mounted in the same way as the top bar. And the gaps between the window frame and the wall must be filled with construction foam, for which the surface is first moistened with water. After that, you need to lean the plastic panel against the base and fix it with metal screws.

Fixing PVC panels

Installing F profiles

F profile is cut and inserted at the edges of the panels. In those areas where the corners are in contact with the fasteners, you will need to make a small incision. At the same time, the slopes of the front door should be decorated with a decorative stone, which looks very expensive. At the end of the work, you need to fill the joints with sealant white color, gently filling the gap with the composition, removing excess volume.

These measures will not only make the window even more attractive, but also protect it from mold, fungus, and early wear.

F profile for slopes

Sandwich panels

Repair of window and front door slopes can be done with sandwich slabs, as shown in the following photo. Window sills, the window is decorated with sandwich slabs, and the slope of the doors with decorative stone. Sandwich boards retain their visual appeal and original operational parameters for a long time.

According to all the rules and norms, the repair of structural elements of the window made it possible to increase the degree of resistance of windows to the negative impact of negative factors inside and outside the house. The distance between the wall and the sandwich slab must be filled with building foam, which will act as an additional insulation for the structure.

The installation of such plates is not particularly difficult. Sandwich plate is fixed on the base with liquid nails, which will provide the connection with high practicality, density, durability. Check the slope angles for compliance with the bevel.

Sandwich slabs should be mounted on wooden blocks, which will make it possible to give the slope surface perfect evenness even if the slope deviates from the vertical. To provide the joints of the plates with a neat appearance, they must be treated with silicone.

Scheme of mounting PVC sandwich panels on window slopes

Plastering

Finishing window slopes outside or inside the house is often done by plastering the surface. But to apply this method is relevant only if the slopes are perfectly even. The layer of plaster mass should not exceed 2 cm in thickness, otherwise the slopes will quickly crack and become unusable. This type of finish is successfully combined with the finish of door slopes. artificial stone.

Common mistakes

It often happens that the finishing of window slopes inside is carried out in violation of technology, which entails a number of negative consequences. In other words, these structural elements window openings acquire low resistance to negative factors indoors, which entails rapid wear of the slopes. That is why it is so important to identify the most common mistakes that inexperienced builders make when finishing window slopes:

• incorrect measurements of the base for the installation of sandwich or PVC panels, drywall, and so on, which leads to a loose fit of materials to the slopes;
• neglect of an antiseptic, sealant increases the risk of mold, fungus under a sandwich panel, drywall and other options finishing materials for decorating slopes;
• when using plaster mixtures, often inexperienced craftsmen try to correct defects in the base by making an excessively thick layer of finish. And this is unacceptable, since plaster with a thickness of more than 2 cm can crack after drying;
• when finishing door slopes with stone, you should not give preference to too cheap material. Decor, even with artificial stone, cannot be too cheap, because such savings affect the quality of the finish.

The technology of finishing window slopes using plastic panels.

Photo of how you can finish the slopes inside the window

Options for finishing window slopes indoors.

The installation of practical and beautiful plastic windows is accompanied by the need to finish the slopes that provide the window opening better thermal insulation and give it a finished look. The choice of building materials and technology for finishing slopes depends on a number of factors: the tightness of the material, resistance to moisture and temperature extremes, appearance (compatibility with the interior of the room), cost.

The most practical and popular materials for finishing the slopes of plastic windows today are drywall and plastic sandwich panels. Consider the positive and negative aspects of using each of them.

Drywall slope

Drywall, consisting of two sheets of cardboard with gypsum filler inside, is an environmentally friendly material. To install window slopes, moisture-resistant drywall is used.

Mounted in two ways: frame and frameless. The frameless method is used on even slopes and involves the installation of the material using a mounting adhesive. The frame method is used for uneven slope surfaces.

Drywall is attached to a wooden beam or to a structure made of metal profiles(pre-installed with dowels). To improve thermal insulation, drywall slopes should be insulated with mounting foam or mineral wool. After installing the slopes, the seams and surface irregularities are ground and treated with a sealant, and the outer end part along the perimeter is closed with a corner. The last step is painting or wallpapering.

Advantages of plasterboard slopes:

1. The material is durable and with proper care can last up to 20-25 years.

2. Drywall slope has good thermal insulation properties (especially in combination with foam or mineral wool).

3. Unlike other materials, all kinds of defects (scratches, impact dents and any surface contamination) are easily eliminated on drywall.

4. Relatively low price.

Cons slopes of drywall:

1. Low moisture resistance of the material. The operation of drywall in areas with high humidity will lead to the need to periodically repair and paint the surface.

2. Complexity of installation. Installing plasterboard slopes takes a lot of time. In addition, cutting and fitting the material will lead to the formation of a large amount of dust and debris in the apartment.

Slope from plastic sandwich panels

Sandwich panel, due to its structure (plastic, foam polystyrene insulation and moisture-resistant PVC), is an excellent heat-insulating material. It has a quality certificate and is safe for human health.

Most often, the installation of panels is carried out simultaneously with the installation of the window. To do this, it is enough to accurately cut the material and insert it inside a pre-installed starting profile. Sandwich panels are attached to the slopes with a mounting adhesive. From above, the end part along the perimeter is closed with an F-shaped profile. Thus, the installation procedure is completed.

Advantages of slopes from sandwich panels:

1. Specifications panels provide slopes with durability and excellent thermal insulation, there is no need for additional insulation.

2. Unlike other materials, sandwich panels do not need to be processed or painted after installation. The color matches the color of the window frame.

3. The panels are resistant to temperature extremes and high humidity, making them easy to care for (for example, wash with detergents).

4. Quick and clean (compared to drywall) installation.

Cons of slopes from sandwich panels:

1. The main disadvantage of the material is that if the surface of the panel is damaged, the defect (pothole, deep scratch) cannot be quietly eliminated. As a result, you will have to change the entire panel.

In addition, these panels are quite soft and easily pressed through, for example, by blinds fittings when opening a window.

2. The price of some models of sandwich panels can significantly exceed the cost of other materials (for example, drywall).

What trim finish to choose?

We usually make our choice, taking into account offers from professionals who will be engaged in the supply and installation of windows, including a price offer. For example, you can find out about plastic windows from a manufacturer in St. Petersburg from StroyComfort representatives. But in principle, it is possible to decide on the option for finishing the slopes even before calling the masters, taking into account the above properties of the materials. First of all, for this you need to know:

Type of premises (residential, commercial, special purpose). So, in a room subject to large temperature fluctuations and high humidity, drywall should not be installed.

Dimensions and characteristics of the window opening. Usually, in a badly damaged window opening, plasterboard finishing of slopes is done.

Contamination of the premises, i.e. the possibility of implementation wet cleaning slopes.

In any case, no matter what material you choose, the main thing is to make a high-quality installation of the slopes themselves. Not only the appearance of the room will depend on this, but also the tightness of the window opening, the thermal insulation of the entire room.