Wooden bar stool with her hands. How to make a bar stool with your own hands? Folding bar chair do it yourself from a tree

If the area of \u200b\u200byour apartment or the house allows you to add dwellings to your liking. It is no exception and a kitchen that can be added by bar chairs. Such furniture objects are presented in modern stores, but their cost may be high enough. In addition, some consumers are not satisfied with the design of the described interior items. Therefore, their manufacturing home masters sometimes do on their own.

Preparation of instruments

Bar chairs can be performed with your own hands, only having prepared a certain set of tools and materials. Among the first should be allocated:

• screwdriver drill;
• grinding machine;
• pencil;
• drill;
• lobzik;
• plane;
• roulette.

Preparing the screwdriver, you must take care of the presence of a set of bits. The jigscription must have a pink that will allow purely cutting plywood and wood. The grinding machine can be replaced by sandpaper. As for the drill, their length should be 3 and 6 mm.

Production of chair array of wood

If you decide to make bar chairs with your own hands, you can use the birch or pine. Birch array better suitableIf you are planning to tint products, because pine is scorched unevenly. For work, an array will be required, the thickness of which is 20 and 30 mm.

Of the material of greater thickness, it is necessary to cut a circle, the diameter of which will be 360 \u200b\u200bmm. This part will become a sidew. If you have access to a manual milling or milling machine, you can select a profile around the perimeter. If there is no such possibility, then you should remove the uniform chamfer, and after passing the surface. This recommendation applies to all billets.

If you decide to make bar chairs with your own hands, then in the next step a small circle, the diameter of which is 260 mm, it will be necessary to cut out of the massif of a smaller thickness. From the same material it is necessary to cut the ribnes ribs that perform the role of footrest. The legs should be cut out of an array of more impressive thickness. It is important to draw attention to the fact that the structure of wood should be vertical.

Screed applied screws. Dimensions equal to 5x80 mm will be needed to screw the legs to a small circle and to each other. In order to fix the seat to a small circle, you should use 5x40 mm screws. For installation of ribs, 5x20 mm screws are used. Ribs must be installed on the legs with the help of the corners. At the final stage, the product can be covered with a verse by drying it, and after painting with several layers of varnish.

Another option for the manufacture of a bar stool

If you decide to make bar chairs with your own hands, you should consider several technologies at once. The second involves the use of plywood, the thickness of which can vary in the range from 25 to 30 mm. The legs can be made of balasine or cuttings for shovel. The diameter of these elements should be approximately 30 mm.

To perform work, prepare 30 mm drill. For one stool, you will need four legs, the length of each of which is 750 mm. The radius of the seat will be equivalent to 180 mm. It will also be necessary to cut the rough seat, its radius should be 170 mm. When a bar stool is performed from a tree with their own hands, it will be necessary to cut the upper ring, its external radius should be equal to 143 mm, while the inner will be 110 mm. The bottom ring must have external and inner radii, which are equal to 153 mm and 120 mm, respectively.

Methods of work

Before starting to drink rings, they should be placed under the control. At the workpiece, it is necessary to draw an external circuit of the circle and spend two perpendicular straight lines through the center. From the crosshair should be postponed 140 mm in each direction, which will allow the central points of the holes, they should be selected by a perovy drill.

Then the inner contour is determined, at this stage you will need to cut the ring from the workpiece. The draft seat is placed on the same technology as the top ring. However, drill only half of the thickness. This will allow you to get the nests for installing the legs. When the bar stool is performed from the tree with their own hands, the details should be processed, as in the first embodiment of the chair.

To the rings legs should be fixed with furniture screws. They will need 8 pieces, and each will be equal to 6x70 mm. We should not forget about the washers. For them, it will be necessary to prepare holes. The top ring does not need to tighten the tight. First, the legs are installed in the sockets, where it is pre-pouring a bit of joinery glue.

The draft seat is additionally screwed to the legs of 5x60 mm screws. It is important to restore the fasteners heads. The main seat is strengthened from above, it is necessary to strengthen it from below, using the screws of 4x40 mm. Before making a bar stool with your own hands, you must prepare a veil. It is covered by the surface of the chair at the final stage.

Making a metal bar stool

Bar stool You can also do it from the metal too. If the arsenal has remnants of leaf iron or metal profile, then all these materials will go into force. The form of the future seat must be depicted on the surface of the asbestos sheet for welding. Using the sketch, you should cut blanks and weld them with each other. As a result, a polygon will be obtained, the inner plane of which is still to be filled.

For this billet, cut from the same strip, you can use yourself invented pattern. The blanks are welded with each other and are cleaned, and the angles should be rounded. The legs are welded to the seat, for this you can use a profile with dimensions equal to 30x20 mm.

If you decide to make bar chairs with your own hands, the photo is first recommended to consider. They will allow you to avoid many mistakes. In the process of welding, the legs will need to grab on one welding point. Stop levels for the legs are marked at a distance of 45 cm from the seat. This should be guided by the comfort of the use of the future stool.

Stop for the legs should be performed from the same profile. In order for the legs not to pay finish finish Floor, you can wear rubber or plastic corks, in return for which decorative heels are sometimes used. Previously, they should be turned in size and polished.

Conclusion

Corks no need to fix screws or glue, they will be held independently. The main requirement is to subside them to fit under the size of the legs. When such a bar stool is performed with their own hands, the drawings are preferably prepared. Thanks to them you can accurately calculate required amount Material, and indeed facilitate the work process. Well, at the final stage, the chair should be painted, however, it is necessary to cover it with a layer of soil.

Happy residents of apartments acceptable planning or private houses have long understood the charms of free movement in the kitchen. And many Male owners gladly continue to improve the interior and furniture are self-work. Quite often there are options for combining kitchen and table spaces. As a rule, they are turned off with bar counter racks or kitchen "appendixes" - continuations of countertops. Chairs sold in stores or stools for such racks often have absolutely no "home" look, so we offer to make a bar stool with your own hands.

Exterior of the first bar stool

For both options below you will need manual power tools. In this case, it is not necessary to order sawing on the side, since all the details are figured and relatively small size. The blanks for them can be bought in the Stroymarket, in the departments selling Phaneur and furniture shields.

Required tools

• Screwdriver-drill with a set of bits.
• Lobzik electric with saws for pure tree cutting and plywood.
• Grinding machine or simply sandpaper and many patience.
• Plane.
• Pencil.
• Roulette.
• Drills of diameters 6 and 3 mm.

Bar chair from the wood array

The most affordable wood breeds sold immediately as furniture shields - It is pine and birch. If you plan to tint the product, then it is better to cover the birch array to choose a birch array, because the pine is scorched unevenly.

We will need an array of two thicknesses: 30 and 20 mm.

From the thirtyMillimeter, cut out the logs of a 360 mm diameter circle - it will be a seat, then you mean the top of the chairs. If you have access to a milling machine or manual frezer - You can choose around the perimeter a beautiful profile shaped milling cutter. If there is no such possibility - simply remove the uniform chamfer with the Rubankom and stabbing. This applies to all the details.

Large and Small Circles

The small circle, a diameter of 260 mm, is cut out of an array of 20 mm thick. From it, the rigid robbers, which serve as a footrest.

Drawing Bar Chairs

The accurate drawing of the ribbie and the legs of the chair with the dimensions you see in the pictures. The legs are cut out of the array of thirties, and you need to pay attention to the structure of the tree for the legs vertical.

Drawing Röber rigidity

The order of assembly is visible in the pictures, for the screeds you need to use the screws of three species:

• 5x80 - to screw the legs to each other and to a small circle.
• 5x40 - for fastening the seat to a small circle.
• 5x20 - for fastening Röber rigidity. These parts are screwed to the legs with the help of the corners supplied from the bottom side of the floor.

In the plane under the self-tapping screw, drills the hole with a diameter of 6 mm, in the end - with a diameter of 3 mm.

Assembling bar stool

Tinging the verse, we certainly dry and cover the two-three layers of varnish. Bar chair is ready.

Second version of the bar stool

For the second option, we use the plywood, 25-30 mm thick. The legs for it can be made from the balusc of the round section or simple cuttings for the shovel, with a diameter of about 30 mm. To make the bar chairs with their own hands, as shown in the figure, we will additionally need the first drill the same diameter as the legs, that is, 30 mm.

Second version of the bar stool

So, Details:

• Legs length 750 mm - 4 pcs.
• Seat, radius 180 mm.
• Chernot seat, radius 170 mm.
• Ring upper: external radius 143 mm, internal - 110 mm.
• Ring Lower: external radius 153 mm, internal - 120 mm.

Drawing bar stool

Before drinking rings, placing them under the control. Blacks in the workpiece of the outer circuit of the ring and spend through the center of the resulting circle two perpendicular to each other are straight. From the crossing of 140 mm in each direction - we get centers of holes that need to choose a perovy drill, only four. Blacks internal circuit and drink a ring from the clustered billet.

Drink rings

The draft seat is also placed as the top ring, but drills only half of the thickness - it will be "nele" under the legs.

All parts are processed in the same way as in the first, wooden, variant of the bar stool.

The legs to the rings are fastened with the help of furniture screws at the height: small 100 mm from the top, large - 250 mm below. Furniture screws with decorative hats We buy in a construction store, 6x70 mm - 8 pcs., Do not forget about the washers. Drills for them holes with a drill of 6 mm. Upper ring until we attract tightly - first insert the legs into the snobs of the rough seats, where it is pre-poured a bit of joinery and pva.

Additionally, we screw the draft seat to the legs of 5x60 screws, trying to drown the heads of the screws. We glue from above the main seat and fix it from the bottom, from the draft, 4x40 screws.

Tinging the product by a verse, cover with varnish, call bartender.

Now we know how to make a bar stool with your own hands, and even in two versions. Objectively - they differ slightly, but! With an array of wood for the first option there are unpleasant incidents. Choosing a blank in the store for your details, certainly find out the seller: is the construction of this array or decorative?

The decorative array of wood may look more attractive, but he will not stand serious loads. With plywood in this regard is easier and more reliable.

Good luck to you.

The spacious kitchen allows you to use the space to the maximum: here you can place not only the familiar dining table, but also a bar rack with chairs. Make a bar stool at home with your own hands, having a minimum set of tools and possessing the azami woodwork. A little more difficult to make furniture for the kitchen from metal pipes.

Design furniture

It is necessary to start making a bar stool with your own hands with the definition of material, as well as from measurements and creating a drawing. It is better to do the design of wood (pine, birch) or metal (from pipes). A good economy version - plywood or chipboard panels, they are reliable and durable. By selecting the material for the product, you can move to the next step - inventing the shape and creating the drawing.

Bar chairs do it yourself should have long legs, but everything else is at will. For example, the design may have a small back or soft seat square or round Forms. All this must reflect the drawings. When they are developed, it is necessary to take the height of the bar rack and take 350 mm. Thus, it turns out the correct and convenient to use the height of the furniture. This is a standard calculation. As for the height of the back, it should be not lower than 20 and no higher than 60 cm.

Features of the creation of a bar stool

Decided to make a tree stool? The logs are an excellent workpiece for the product.

Their thickness should be at least 20-30 cm, otherwise the chair will be seen. However, if the material thickness is greater, it is difficult to work with it. You need to cut the logs to 10 parts that must match the sizes in the drawings.

• Circle for the seat. Thickness - 30 mm, diameter - 350 mm.
• Support for the seats in the form of a circle. Thickness - 20 mm, diameter - 250 mm.
• 4 Wooden legs. Thickness - 30 mm.
• 4 strips for rigid rigid design. Thickness - 30 mm.

Please note: Cuts should be made vertically so that the wood structure is not damaged and remains vertical, otherwise it will reduce the strength of the chair.

After cutting the stage of assembling the product comes. To do this, you will need:

• metal corners for fastening rigidity to legs;
• 5x80 mm screw to fix the legs of the structure between themselves and to screw them into a small circle;
• self-tapping screw 5x20 mm to fix rigid ribs;
• self-tapping screw 5x40 mm for fasteners of the seat to a small circle.

It is necessary to start collecting a wooden chair according to such a scheme: the legs are bonded between themselves, then they are installed on the metal corners of the ribbon ribs, the small circle is screwed to the legs, and the main seat is fixed on top to the entire design. Chair ready! The product is covered with varnish for practicality.

Second version of the wooden chair

The classic option for the kitchen is a high chair with a rectangular seat. As in the first version, in the calculation of the height, it is necessary to repel from the height of the bar counter. Classic optimal parameters are shown in the figure.

Logs will be suitable as the material. Their thickness should be 30 mm, size 5 × 5 cm. After cutting the logs to the required parts, you can proceed to the collection of furniture.

Collect stools Begin from the legs. So that they are under a bias to each other, you need to transform them by sending 5 degrees corners and chamdes at both ends. Now you can fix the upper and lower planks. Thus, it turned out 2 parts of the chair, parallel to each other. The next step is to attach perpendicular partitions - at the top and bottom. It is important to understand that the lower perpendicular partition will serve as a support for the legs, so it is necessary to attach it at a convenient level.

Go to the manufacture of the seat. At the end of the board should be marked, and after cutting the necessary form. Make unusual bends will help a circular saw. Be sure to clean the part with a grinding machine.

The final stage is the connection of the legs of the chair and the seat. In the tops of the legs and the bottom of the seat, the holes are drilled, with the help of pins 2 parts are fastened. You can plant them not only on the pins, but also to glue the PVA glue so that the chair becomes more stable. The product is covered with varnish or paint.

Bar Metal Chair

The product from the metal will be decorated with a kitchen interior in Loft or Industrial styles. Special metal chair It will look original at the bar counter in the kitchen. It can be made of iron pipes.

To create furniture will take:

• iron cutout
• the workpiece of pipes is preferably made of stainless steel (nickel-plated, chromed, anodized),
• leaf plywood or chipboard.

The pipe diameter depends on the type of furniture. But it should be borne in mind that the design must withstand human weight and the pressure of the seat. It is recommended to take a material with a diameter of at least 5 cm. The height of the legs is determined and the billet of the pipes of the required length is cut, better with a small margin of 1-2 cm.

Now it is necessary to give the form of material. You can do this with the help of a pipe bender: the tops of the pipes are bent into the form of a semicircle. They are fastened with fixing bolts among themselves.

Seat can be made of metal or plywood. In the first embodiment, the necessary form is drawn on the cutting cut, then cut and fastened to the curved billet from the pipes using welding or bolts. In the second embodiment, the plywood base is cut out the necessary form and is attached to a metal frame. In this case, the seat should be covered with a fabor with a foam rubber so that it is convenient for use. Please note: the chair on the iron legs can scratch the floor, so it is worth "putting" plastic or rubber "socks".

Recently, the interior items in the style of Handmade are becoming increasingly popular. They attach individuality to the room and can fully characterize their owner. Look original kitchen furniture, created by own design. For example, make the bar stool with your own hands is not so difficult. Such a passion can become not only a full hobby, but also a good earnings.

Opening any directory of bar furniture, simply unreal unreal overnight to stop his glance on a specific model, because the variety of shapes and colors amazes. At the same time, it is not always possible to find something suitable for your interior. In this case, it is worth making furniture yourself. In the manufacture of bar chairs, it is necessary to consider a number of important parameters.

Competently calculated stool height - pledge convenience. The optimal distance from the seat to the bar counter is 25-30 centimeters. The presence of such space provides comfort and freedom of movement.

The large surface area of \u200b\u200bfurniture contributes to relaxation, immersion in the atmosphere of comfort. However, not every bar table can afford a wide range. Thinking about to make a chair yourself, it is necessary to count the size of the seat based on the width, the depth of the table top. It is desirable that during operation there is no interference within a radius of 20 centimeters. It will provide comfort without disturbing the person's personal space sitting at the bar counter.

When developing the design of the chair, it is necessary to think over the following components:

1. Base. Of course, everyone's preferences are different, however, experts recommend using four legs. They will give a barn chair with a maximum of sustainability and reliability. We will certainly think about the possibility of adjusting the height, provided that among family members, relatives, familiar people have different growth.
2. Back. For snacks or other short-term use of the chair, this parameter is not particularly important. If a long period of time is planned, it will be reasonable to stop its choice on a high, well-fixed back, on which you can leak at any time.
3. Armrests. This design element is voluntary. Special recommendations do not exist. It all depends on personal preferences.
4. Upholstery. Its presence is due to the arrangement of priorities between style and comfort. Hard seats of chair, made of metal, acrylic, plastic, tree look more stylish, perfectly fitting in modern interior. Soft models, covered with cloth or leather, are pleasant to the touch, more comfortable.

In the matter of choice of design, the shared interior of the room is a decisive factor. Traditional furniture, for example, it will not be quite appropriate to look at the room decorated in High-tech styles, Bionics or Brutalism. Bar chair made with their own hands should harmoniously fit into the design of the room, do not get out of the overall picture.

Furniture coloring is better to choose from the total color Gamma. premises. This is especially important for the foundation. But as for the seat of the chair, then it is recommended to give fantasy will. You can choose options ranging from one-photo version and ending with floral or animal prints. Then the bar stool will become a bright highlight in the interior.

On four legs

With back

With armrests

With the upholstery and without

Bright design

What materials can be made

The basis is a kind of foundation of the entire product that takes on the main load is responsible for reliability and stability. Consequently, if among those who will sit on the bar stool, there are people with weight exceeding 90 kilograms, preference should be given to more durable materials. These include wood, metal. The latter looks very expensive, solid, but gives the product a considerable weight.

If it is decided not to use the seat upholstery, then this design element can be made from natural tree. This noble material will give a barn chair a view of an expensive, status furniture. His drawback is at high cost. It is allowed to use plastic. Special attention should be paid to the transparent option. It is appropriate when creating an atmosphere of lightness and airiness. However, we should not forget that this material does not differ in strength and, as a result, can give a crack during long-term use.

If it is decided to make the seat softer, cozy, then you can choose textiles or skin as a upholstery. Natural materials are more suitable for the classic version of the bar stool. Artificial is better to use when creating a product in the style of High-tech and the like.

Make your own hands the bar stools can be completely from one material or combine several options. This will give the charm the details of the interior, will make it possible to implement any fantasy. In addition, such a design will positively affect the final cost and functionality of the product.

Tree

Metal

Plastic

With leather upholstery

Required tools

In order to make bar chairs with your own hands, you must have a certain set of tools in arsenal. Most devices are universal, but there are also those that can be used only when working with a tree or metal. If they are not available, you can rent.

Tool	Purpose	Possibility of use for wood	Possibility of use for metal
Pencil	Application of marking
Screwdriver	Minting and Missing Details with Threaded
	Accurate measurements
Galnik	Construction of angles at 30 °, 45 °, 60 °
Chisel	Selection of recesses, scrolling grooves, creating drawing
	Cutting blanks
Sandpaper	Processing product
	Connection of parts of construction
Drill with drills with a diameter of 3 mm and 6 mm	Creating holes
	Bonding materials
Electric logsik	Sawing materials, creating curvilinear propuls
	Hollow out holes
	Shock work
Screwdriver	Spinning and unscrewing connecting elements, drill holes
	Podep detail
Solvent	Giving paintwork liquids of the desired consistency
	Coloring of the surface
	Coating outdoor sides of the product with a shiny layer
	Application of coloring components

At first glance it may seem that equipment and materials are too much. But experienced masters They know that it is better to have an excess device in their arsenal than at the right moment, during the creative process, interrupted and run into the construction department, for example, for the necessary drills or a planer.

Dimensions and drawings

Before the start of the manufacture of the bar stool, you need to arm it with its drawing. This will determine the list required tools, accurately calculate the amount of material and avoid errors in work. The easiest and fastest way is to download the ready version. But since no one can give one hundred percent warranty for the accuracy of the information, then it is necessary to reinstate and personally check all the indicated dimensions.

The following option is to independently draw the future bar stool using special computer programs. This process takes longer, but it gives a guarantee of creating a unique product. If there is no possibility or computer skills, then the drawings can be sketched manually. To do this, you will need only a sheet of paper, pencil, line and excellent fantasy.

How will the drawing appear, does not have a fundamental importance. The most important thing - right sizes. It is from them that depends on the quality of the bar stool. It should be accurately measured and apply the following dimensions on the drawing:

• the height of the floor from the floor to the seat (equal to the distance to the countertop minus 25-30 cm); standard - about 75-85 cm;
• the height of the back (with its presence) is about 20 cm;
• length and seats width - at least 35 cm;
• distance between legs at the floor level is approximately 44 cm.

The above standard dimensions May vary according to individual preferences and dimensions of the bar counter. It will be interesting to look for a folding chair with adjustable backrest and sliding legs. For it, all parameters in the retractable state are taken into account in the drawing.

Making your own hands

Bar chair can be made with her own trees in the form of a tool or with a soft seat and back, as well as from plywood and metal. When working with the last material from the wizard, certain skills in welding are required. Therefore, the profile tube is most often used for which special knowledge is not needed.

Wooden stool

Furniture from wood harmoniously fits into many interiors. It creates an indescribable atmosphere of comfort, comfort and heat. And chair made own handswill bring both aesthetic joy and practical benefits. The novice master is recommended to try to create a simple wooden stool first, following the steps:

1. Purchase of wood. Self affordable materials - Pine and birch. Purchase better shields with a thickness of 20-30 mm. If there is old, unnecessary wooden furniture, you can use it.
2. Applying markings on the material according to the drawing with a pencil.
3. Cutting parts using jigsaw. One circle - the seat itself with a diameter of 36 cm and a thickness of 3 cm, the second - a substrate under it with a diameter of 26 cm and 2 cm thick. 3 cm thick (vertical wood structure), four ribs stiffe . The legs are recommended to shift the plane along the entire length, reducing the thickness of the book to 2.5 cm.
4. Build chair. With a screwdriver or screwdriver, 5 x 80 screws are connected to a small circle, with a small circle, 5 x 40 seats screws to a small circle, 5 x 20 self-testers by means of stiffening ribs are attached to supports.
5. Grinding the whole chair with sandpaper.
6. Coating the product with a brush with a virtue with a brush.
7. Wooden stool ready.

The undoubted advantages of wooden products are strength and aesthetics. But you need to take into account such a moment: when in contact with water or with high humidity in the room, the product can quickly come into disrepair, swell.

According to drawings we make markup

Cut the details

Collect chair

Wooden stool ready

From wood with soft seat and back

Having trained on the bar stool in the form of a stupor, you can move to the creation of a wooden model with a soft seat and back. Such a product is more comfortable and aesthetic. Below Dana step-by-step instruction for the manufacture and fastening of parts and the description of the process:

1. Purchased materials for stool.
2. Wood markings are applied.
3. Moved parts made of wood. The tools will need a logs and chisel. It will also require details with next dimensions: seat 34 x 34 x 2.5 cm, two front legs 2 x 44 x 74 cm, two hind legs 2 x 44 x 99 cm, front Tsarga 2 x 44 x 27.2 cm, rear king 2 x 44 x 32 cm , two side connecting sheets 2 x 44 x 29.6 cm, two pods of 1.5 x 22 cm, four side pods 15 x 29.6 cm, two crossbars for the back 2 x 44 x 38 cm.
4. The frontal part of the seat of the chair is covered by an arc, swelling with sandpaper. On the other hand, the chisses of 2 x 2 cm particles are knocked out.
5. In all the king, the spikes are made, on the side with the help of a drill, two deaf holes of 0.8 cm are dried.
6. In the legs, nests are created under the spikes of the connecting planks according to the drawing. In the rear elements is preparing a place for the back. With the help of chisels, the upper part of 2 x 2.5 cm is removed.
7. All parts are thoroughly polished by sandpaper.
8. Then you need to collect a chair with a screwdriver, drill and screws.
9. Paintwork work.

To create a soft seat, the following items are needed:

• furniture foam or batting as a substrate;
• upholstery Material: Natural or Artificial Leather, Textiles;
• stapler and glue for furniture.

On the top and side sides of the seat, the edges of the filler and the edge of the upholstery material are applied and withstands about 3-4 minutes. Then the substrate is tightly pressed to the base and is covered with the upholstery material, which is fixed with the furniture stapler. After that, the seat is attached to the already made, painted chairs frame.

From wood make parts

From the details we collect a frame

Fasten with screws

Carefully grind

We carry out paintwork

We prepare the foam and upholstery material

Cut the foam rubber on the size of the seat and back

We are tightening the upholstery cloth and fasten the stapler

Seat and back boat to frame

Bar chair with back and soft seat ready

From profile pipe

Recently, metal pipes have become widespread in the manufacture of furniture. Master classes with their use are recommended by novice craftsmen. Of profile pipe The chassis itself is done. Consequently, it is better to give preference to stainless steel, because it is characterized by durability and durability. How to make a bar stool with your own hands from the pipes - about this next master class. You must follow the instructions below:

1. Stocking required material and tools: foam rubber, upholstery, metal pipes, fasteners, chipboard or plywood, pipe bending, drill, screwdriver or screwdriver, construction stapler.
2. In accordance with the drawing, cut the blanks from metal profile. After that, give the upper part of the pipes with a semicircular form with the help of pipe bend.
3. Connect the curved parts with each other by fasteners using a screwdriver or screwdriver.
4. Seat cut from plywood or chipboard. The form can be both round and square. To give softness to impose a foam rubber, cover with the cloth and all this is fixed from the bottom side by the stapler.
5. Two parts of the design compound with bolts.
6. The plastic or rubber plugs should be inserted into metal pipes. This will allow to protect the floor from scratches.

The chair made of pipes will perfectly fit into the interior created in the style of Hi-tech. Classic kitchenBy playing in contrast, he will add the ease of the atmosphere of the bar, and in minimalist will be perfectly harmonized with the design of the room.

We prepare materials

We collect parts of the chair with the help of corners and fasteners

Assembled metal pipe frame

Finish metal carcass to the prepared wooden seat

Install protective plugs

Bar chair from the profile pipe is ready

From plywood

Quite simple in the work material is plywood. In contrast, it is more moisture resistant and reliable in operation. The instruction of creating such a model is similar to the manufacture of a bar stool from a tree:

• in accordance with the drawing on the Faner, markup is applied, then with the help of the jigsaw blanks of parts (legs and seat), which are subsequently polished by sandpaper;
• on the details with a drill, holes for hinges are created, the lobs are crushed;
• all components are collected in one design;
• the chair is covered with varnish or paint.

Most optimal option When creating a bar stool, the use of coniferous plywood. This material of wearless, long retains an attractive appearanceless susceptible to the spread of fungi and the appearance of bugs. In addition, the first time of coniferous plywood products will have a pleasant fragrance.

On the plywood sheet we apply markup and drink the details

We collect a back

Bar stool from plywood ready

Ways to decorate

It can be decorated to decorate it in various ways to give a bar chair of individuality. Due to the diversity of colors, prints upholstery, made of leather or textiles (jacquard, microfiber, silk), will make furniture with a bright element of the interior. Covers will be an excellent solution for those who do not want to do crap. They are practical, they can be replaced at any time.

Decoupage is gaining increasingly popular when decorating furniture. It is used when working with a tree as follows: the surface istented by sandpaper, shutting down with a putty and paint, then the scenery of napkins, flower pictures are pasted. In conclusion, the product is covered with varnish.

If creative abilities are not developed enough or simply no time, you can decorate a chair with bright colors, which will also give him uniqueness. Interesting decision It will be the use of a jute rope - it is possible to wind the structural elements. The choice of decoration methods is huge. It all depends on flavors, desires, abilities, fantasies. Be that as it may, the bar stool, manufactured and decorated with their own hands, will become a highlight of any interior, the pride of the master.

In the technique of decoupage

(no ratings no)

If your home or apartment has a bar rack, you can add it to the chairs of exclusive work. To do this, you will need only a few simple joinery tools, a piece of plywood or boards, bars and some free time. So, we describe in detail how to make a bar stool with your own hands.

Details of the bar stool and their size

In essence, the bar stool is a high stool with the steps. Depending on your desire, it can be both massive, made of thick timber, and light, elegant, with round or square legs. The principle of its assembly in any case will be the same.

The height of the bar chairs should be such that between them and the countertop remained 30-45 cm. Seat can be made from prefabricated boards or two plywood circles (Faneru better take the bottle, from 3 mm so that it does not rush and fail under weight weight). The first round will perform the role of intermediate fastening, and the second seat serves.

For room in the style of Country, you can make a more massive bar stool with thick square legs. If they are a little expanding the book, then the product will be not only more aesthetic externally, but also more stable. Round and even accurate legs can be ordered in a carpentry workshop or buy in the online store. If you know how to work with a tree a little, you can also pull them out and even on the simplest homemade turning machine. The curvilinear parts are fixed with a plumbing (arctic saw).

Round and accurate legs

Sawing details

1. Just as for the usual stool, we will need for a bar stool: 1 seat, 4 legs, 4 prodes (bars connecting legs in the middle or lower part) and 4 kings (bars located under the seat). Naturally, all pair parts should be equal in size.

2. For longitudinal sawming, the workpiece is better fixed in the workbench clamp.

3. To get a steady product, cutting must be made strictly at 90 °.

4. Do not forget that when determining the length of the pride and the CARG, it is necessary to add the length of the spikes.

5. The sawing starts from one end, and, reaching the middle, take out the workpiece, turn over, reinforce and continue to work on the other side. Since to get a smooth surface edge, we will have to complate, and then grind the sandpaper, it is worth leaving a small allowance of millimeters 5.

6. In order not to catch the sowing, carefully process at the beginning large, and then a small forehead every detail.

Original bar stool

Spikes and grooves

On the network, some users recommend not to bother and fasten the legs on the bolts. Moreover, such products recently began to appear even on the shelves of furniture stores. But, alas, the chair, collected by this method, is overwhelmed after a couple of weeks. Therefore, we advise you to use the standard method of assembling furniture - schip-groove. In this case, the end of the part is included in the groove, the fibers in which are located across, which makes it possible to ensure high strength of the product. With a dense fit, such a compound can withstand even oblique load.

Schip-groove

On the milling machine It can be done in a matter of minutes. However, manually, the old Dedovsky way, prepare several fasteners of spike grooves for the chair quite real. To do this, it is enough to have at hand only lobzik or saw with small teeth and rasp. Skipping grooves produced chisel. Very convenient to choose a tree from the groove styhelem - Steel cutter.

1. The width of the spike-groove compound according to the standard should be one third of the thickness of the workpiece, and its length is 80% of the width of the part.

2. The location of the prideration is determined arbitrarily. Since the legs in the bar stool are quite long, the design can be reinforced with additional subtle pripers located closer to the seat. They are made more subtle than the lower.

3. Work starts with the creation of a groove. In this case, the spike will be easier to fit, using the groove as a pattern. We plan its length, making a pencil line on the side of the bar. First, we prepare a few small holes in a row drill or screwdriver, and then choose the chisel Surplus wood.

4. Now do it spike. Drink it more convenient to the jigsaw or saw with small teeth. The workpiece is pre-fixed in the workbench clamp. For attaching a small thickness bar (up to 4 cm) a sufficient single spike.

Creating a cut for spike

You can make I. plug-in spikes (braided). Holes for them (as well as for standard spikes) are preparing a little deeper by 2 mm of their depths of their driving - in it free space We will drip glue. Accordingly, it is necessary to score thoroughly into the hole so that it takes up 3-4 mm less than the thickness of the part.

Plug-in spikes (braided)

Order assembly

1. To check at the beginning we collect Chair dry, without glue: the first two legs we connect the kinga and the pod, then we prepare the second one, but only then we connect both frames. We check all the angles with the help of the square. Slept or ducklings will give the product a slopeful look, so even small defects should be eliminated.

2. If there are no errors, we drip into the holes slightly glue, neatly distribute it to a small brush or a rays and a rubber hammer (Cyanka) carefully scored in a spike.

3. So that the prodes (bottom planks) can serve as a support for the legs, it is better to lower them down.

Thinner additional pods can be made and closer to the seat

4. The seat is secure to the kings with screws or glue.

5. After complete grazing, the product can be simply covered with a mourn or paint in the desired color.

6. As a stuffed material for the seat, we use foam rubber or foam, and for the upholstery itself, synthetic skin or any solid fabric is furniture, tapestry, etc.

7. The seat of the bar stool can be simply painted in a contrasting color.

Bar chair with decorative seat

Video: how to make a simple bar stool