The stove from the cast-iron bath to the bath drawing. Do-it-yourself stove for a bath from a cast-iron bath. Oven and combustion chamber

There comes a time when plumbing, due to its type or malfunction, becomes unusable. But, having replaced it with a new one, do not rush to throw it away. Summer residents and home owners can easily make a garden oven from cast iron bath, which in terms of strength and service life will not be inferior to factory models.

Advantages of using cast iron

This type of metal is considered to be one of the best furnace materials. Its main advantages are:

1. Environmental safety... Does not release when heated harmful substances.
2. Resistant to temperature extremes... A street oven made of bricks can begin to crumble in a few years.
3. High thermal conductivity... A cast iron fireplace will warm up the room much faster than one built from other materials.
4. Durability. Cast iron is the leader among metals in terms of strength. Even steel ovens are less reliable.
5. Ease of use.
6. Fire safety.

The disadvantages of cast iron that are worth paying attention to are fragility and susceptibility to corrosion. In the first case, unnecessary mechanical influences should be avoided, in the second, the surface should be treated with special solutions.

A homemade cast iron construction will not turn out very beautiful, so it is recommended to overlay it with brick or stone.

Preparation of materials and tools

To create such a wonderful oven from a bath, you need to prepare:

• angle grinder (grinder);
• 2-3 circles for metal at least 1 mm thick, 12.5 cm in diameter;
• electric drill;
• drills for metal with a diameter of 9, 11 mm;
• grinding wheels;
• files;
• hammer;
• level;
• construction gun (for applying sealant);
• plumb line;
• putty knife;
• master OK.

Materials you will need:

• iron or steel sheet 5 mm;
• refractory red brick;
• grate;
• sealant;
• clay;
• sand;
• metal corner;
• bolts with nuts, washers;
• chimney pipe with a diameter of 12 cm.

Photo: the material has been prepared, it remains to choose the purpose of the furnace and get to work

When all the materials and tools are collected, you can start cutting the container. For convenience, it can be turned upside down or laid on its side.

Users often search:

You need to handle the grinder carefully so as not to damage the surface.

Before you start sawing a bathtub, it is worth considering a few nuances:

1. Marking will make it easier to cut the product.
2. The first is to remove the enamel layer strictly along the drawn line. This will help prevent chipping around the edges.
3. The next step is to cut the cast iron. This is done gradually, in small pieces of about 10 cm, so as not to overheat the grinder.
4. When the tub has already been sawn in half, supports are placed under each part. They will not let the parts fall and damage the tool and material.

According to experienced builders, it is better to work with a grinder at an angle. This will prevent the enamel from peeling off and all cuts will be smooth without burrs.

Provided you use a high-quality grinder, the processing of cast iron will take no more than 1 hour.

For a barbecue, you will need two halves of the bath: one part will serve as a fuel loading chamber, the other is needed for cooking. For a sauna stove or fireplace, one half will be enough.

Step-by-step creation of a furnace from a bath

Having no construction experience, it is worth consulting about all the intricacies of masonry and installation of parts with a specialist, but it is better to carry out work under the supervision of a master. So the product will be of high quality and standards. fire safety will be respected.

As for the construction of the foundation, its type depends on the total weight of the furnace:

• For a structure over 700 kg, a monolithic or strip base with a depth of 50 cm or more should be equipped. A formwork is constructed around the perimeter of the pit and covered with a layer of rubble or broken brick. It is rammed. Poured with concrete.
• For small ovens, a brick foundation is enough. It is recommended to purchase cement of a grade not lower than M300. Bricks are placed with an edge, fastened together with a solution.

Now consider detailed instructions for the manufacture of each of the furnaces with a different purpose.

For a bath

To create in the steam room the necessary conditions, the design must meet the following requirements:

• have a high heat output;
• regulate convection flows;
• produce enough steam.

The procedure for building a sauna stove:

It is important to note that the foundation must have a ledge on the borders of the furnace of at least 50 cm, and 1–1.5 m of free space must be left in front of the furnace.

An interesting idea is to make a sauna stove from both halves of the bath. The second part will be needed as an extension for heating water, or you can lay out a Russian stove from it.

For cooking

On summer cottage you cannot do without a barbecue or barbecue. And the opportunity to bake delicious bread, fry meat in the fresh air forces the owners to equip small street ovens on the territory.

Here is a description of how to build a barbecue from the bath step by step.

The sequence of work is as follows:

Some craftsmen leave the barbecue in this state, but in order for your oven to look beautiful, you still need to do exterior decoration.

There are several options:

1. Whitewashing of the clay part.
2. Whole masonry ceramic tiles or pieces of it.
3. Surface finish natural stonepre-cut into pieces with a thickness of 10 mm.

The materials are attached to the oven with heat-resistant adhesives.

A good solution is to install the chimney to the stove through the drain hole of the bathtub, expand it beforehand, and only then weld it to the steel sheet.

For heating

In the country, it is easy to build a fireplace from half a bath. He might be:

• Built into the wall... Suitable if the walls are bricked in the house. Will significantly save free space.
• Leaned (half-open)... The firebox is located at a considerable distance from the wall. This fireplace does not need a separate foundation, it is installed directly into the floor. Has good traction, built-in ash pan.

The advantage of using a cast-iron bath for the combustion part is that the fireplace is in the form of an arch and excludes complex brickwork. A hole for the chimney is made at the top of the bath. The outer part is decorated with a fireplace portal.

When building a semi-open fireplace, you should consider the following recommendations:

1. Cement mortar up to 15 mm thick is poured under the base.
2. A metal mesh is laid on top.
3. A layer of waterproofing is applied.
4. Insulation of asbokarton type is being laid.
5. A pedestal is being built under the firebox. Brick, aerated concrete will do. The bonding mixture is cement mortar or heat-resistant glue.
6. The structure is plastered. You can decorate it with stone, ceramic tiles.
7. A gap is left between the cladding and the fireplace insert for the convection heating system.
8. The chimney is mounted in the hole made, and is led out through the ceilings, the roof. Often done in the form of a sleeve.
9. From the inside the firebox, the chimney is sheathed with heat-insulating non-combustible material.
10. The lower part of the fireplace is being finished.
11. The product is closed from the side and from above with a frame made of duralumin corners connected with self-tapping screws.
12. The frame is sheathed with plasterboard.
13. Holes are made in the lining for air ventilation.

When installing the chimney, it is important to take into account that with a pipe height of up to 5 m, the deflection angle is 45 0, over 5 m - no more than 20 0.

For garbage disposal

An unusual solution to build from old bath stove for burning waste.

The principle of its construction is similar to a street barbecue.

Layout of the oven on a brick base

An alternative is to remake the old stove, removing all parts except the grate and the body. Part of the cast iron is welded to the base from the inside to strengthen the structure.

In such a fire trash can you load waste directly from above. When burning, cover the stove with another part of the bath so that the smoke does not dissipate throughout the entire area.

So do not rush to get rid of things that are out of order or lost their appearance. In the right hands, even an old bathtub will get a second life, it will become a functional stove that will last for many years.

It's always a bit of a pity when some old things that have served with faith and truth for many years fall into disrepair. But natural domestic ingenuity often allows breathing a second life into seemingly serving "veterans". For example, very often a sauna stove is made from an old cast-iron bath. The popularity of such a solution is added by the undoubted advantages that such a non-trivial material as cast iron possesses.

• practically unlimited service life. Even the enamel used to cover the bathtubs is practically very difficult to destroy. This can be explained quite simply. IN soviet times the enamel coating was made two-layer using quartz sand, which, when baked, formed a super-strong composition;
• a significant indicator of heat capacity, as well as the accumulation and release of heat;
• high resistance to corrosion.

Required materials and tools

• in fact, an old bathtub, preferably cast iron, although you can use a steel one with a slightly lesser effect;
• steel sheet with a thickness of at least 6 mm;
• steel pipe;
• several bricks;
• metal fasteners;
• angle grinder, she is a Bulgarian;
• welding machine.

Option number 1, universal

Step # 1

Cut the tub in half using a sander. Cast iron is a brittle material (and this is perhaps one of its few disadvantages), therefore, when cutting, you need to be careful to avoid chipping the material. It is necessary to ensure that the grinder does not heat up too much, for which technological breaks are arranged.

Step # 2

Cut off a 6 mm thick metal sheet. or more by the size of the part of the bath prepared by the first step, which in the final design will be located at the bottom. Having previously outlined, cut a hole on the sheet according to the size of the existing pipe. Then weld it in place. Thus, a chimney is gradually formed.

Step # 3

Make a hole in the upper part of the tub, then place both halves on top of each other with a sheet of metal. The pipe must be secured either by welding or using a heat resistant oven sealant. With the same sealant, it is necessary to treat the places where the metal sheet adjoins the halves of the bath, which will avoid possible smoke. The edges of the bath must be securely connected with fasteners.

Step # 4

The base of the future oven is almost ready. Now it must be installed on brickwork to give the structure stability and ease of use. The ends of the future stove, primarily for decorative purposes, are recommended to be sheathed either with ordinary iron sheet or corrugated, which will look even more attractive.

Step # 5

Make metal doors for the firebox and stone chamber. In order to improve the air supply and, as a result, better combustion of firewood, it is necessary to make a certain number of holes in the firebox.

Step 6

The resulting universal oven can be used for a variety of purposes. In order to install it in the bath, it is necessary to make the smallest additions, namely, to place stones in the upper part; connect to the existing chimney or lead the existing pipe outside the steam room.

Option number 2, specialized for a bath

When using a stove only for a bath, a simpler design solution is possible, including virtually eliminating the use of the second part of the bath. In fact, the first half of the bath is used, which is lined with ceramic oven bricks.

Inside the bath, either gas bottle, or a metal drum with a diameter of about 40 cm. A chimney is connected to it, welding it.

Stones (7-15 cm in diameter) are poured into the free space of the bath half, left over from the firebox. As a rule, rose quartzite or granite is used for this.

Video review :

The masonry is carried out at the height of the bath using clay mortar. The main feature is the joining of two very different materials in terms of thermal expansion - brick and cast iron. To do this, it is imperative to provide expansion joints, in which, as a rule, basalt cardboard or asbestos is used.

After completing the masonry work for decorative purposes, the surface can be tiled.

After repairing and replacing an old bathtub with a new one, it often happens that the hand does not rise to throw out a still solid cast-iron product. But what to do with it next? People who have a dacha usually take out items that have become unnecessary to their suburban area, doing so with the expectation, it is imperative to find them in the future any application. We will tell you how to make a stove for a bath from an old cast-iron bath.

Cast iron bathtub, which had to be replaced with more modern versionmay no longer look too fresh in appearance. But it still remains a strong and durable container of a fairly large volume that you want to somehow adapt for your household needs.

There are many uses for a cast iron bathtub.

Most often in the country, a bathtub is used as a reservoir for water used for irrigation, or a container for composting. But there are other ideas as well. For example, you can make an original bathtub garden furniture or build a small artificial pond, which will become a real decoration of the site. And here a lot depends on the imagination of the owner of the cottage. And viewing photos of options already implemented will help you navigate the situation and find something extraordinary for yourself. But you can also make a stove from a cast-iron bath, because they are quite expensive in the store. Cast iron is a material perfectly suitable for this purpose, which differs in:

• high strength;
• good thermal conductivity;
• resistance to high temperatures;
• unpretentious operation.

Decorated cast iron bathtub for collecting water in the country

Of course, all cast iron products, despite their strength, are quite fragile. Therefore, they need to be handled carefully and to avoid the use of unnecessary efforts of a mechanical nature. But still, a good stove structure will turn out from the old bath. One of several options for giving stoves can be made from it:

• outdoor garden;
• fireplace for a country house;
• for a bath.

All these options are quite feasible with your own hands, and watching a video on this topic will help you better understand the process of actions that will be required for the independent construction of the furnace. The bath itself will have to be cut into pieces. But cutting cast iron is not an easy task, requiring certain skills, effort and time.

How to cut a cast iron bath correctly?

This operation must be approached with full responsibility. You need to act very carefully so as not to damage the cast iron product. For cutting, you will need a grinder and several discs for metal. If possible, it is better to work not indoors, but outdoors, doing it in a respirator, goggles and construction gloves. The following sequence of actions must be followed:

• first of all, they mark the future section;

Saw the tub carefully to avoid chipping

• then, along the entire marked line, a layer of enamel is first incised, covering the cast-iron base of the bath, in order to avoid the formation of chips at the edges;
• after that, they begin to saw the cast iron itself with cuts of 10-12 cm, taking breaks when the tool overheats;
• having cut about half of the bathtub, props must be placed under each of the parts, otherwise at the end of the work they may close together and damage the tool.

Council. It is advisable to cut the cast iron base at an angle. In this case, as a result of the reverse movement of the disc, the enamel will not flake off, and the cut itself will turn out to be even. FROM good tool on hands, the work of cutting a cast iron bath into pieces can be done in about an hour.

A stove for a bath from a cast iron bath: how to make it yourself?

It is much more difficult to build a sauna stove than to install an ordinary garden stove on the site. After all, it must be not only effective but also safe. Therefore, you need to take a responsible approach to installing the stove in the room. And in order to quickly navigate in the process of necessary actions, you can see a photo or familiarize yourself with the corresponding video material.

Attention! The construction of a bathhouse and any other stove requires compliance with fire safety rules. For its correct equipment, you need to have at least minimal knowledge and experience. It is better, even before starting work, to pre-consult on this issue with a specialist, having clarified all the subtleties and nuances.

The stove structure in the bathhouse must comply with the following parameters:

• sufficient thermal power with the possibility of changing it;
• ability to store heat and produce steam;
• the ability to regulate convection flows.

A cast iron bath is suitable for building a furnace. standard sizes

After cutting the bath, you can start building the furnace structure. In this case, you can use only one half of the cast-iron container for the equipment of the combustion compartment. But they make bath stoves from two parts of the bath. The second half can go to the construction of a heater or to add a compartment for heating water.

Those who love tinkering with their own hands can build such an unusual sauna stove on their own. This requires:

1. Pour the foundation for the furnace structure from concrete mortar with or without filler. As a filler, you can use, for example, broken brick.
2. Lay half of the cut tub on the foundation with the curved part up. With a cut, the cast-iron container must be built into the wall with removal to another room, from where the furnace will be fired. On this side, the hole is closed brick wall and install a furnace and blower door in it.
3. Around the installed half of the bath, at a distance of about 10 cm, walls of red brick are also erected, equal in height to a cast-iron container. The resulting space is filled with stones, which, when heated, will heat up, then giving off heat to the steam room.

Furnace construction

A fairly simple sauna stove can be built in two tiers. Heat will accumulate in the upper chamber. The principle of operation is as follows: gas, passing through the bath, heats the stones, goes to the opposite side, then goes down, and then up, after which it exits the pipe.

Such non-standard solution, like a stove for a bath from an old bath, is not only original, but also quite simple. Its construction does not require the use of any special materials. A self-made stove structure will last as long as a purchased product. In addition, this option requires significantly less investment than purchasing a finished oven.

Stove from the bath: video

Do-it-yourself stove for a bath from a cast-iron bath

Old cast-iron bathtubs are made of durable material that can withstand any stress and temperature, so do not use it a second time for the benefit of your health - this is big mistake... In addition to its strength, cast iron is also an environmentally friendly material, therefore, during heating, you can rest assured that no harmful substances are released in the bath.

How to make a stove with your own hands?

Of course, after using the bathroom, it may not be in the best condition, but all of its qualities remain the same, for example, it still remains strong and durable, so it is quite possible to give it a second life. Naturally, many who have summer cottages use baths such as a water tank, and those who are great at fantasizing can come up with many other interesting things. If you have a bathhouse at your summer cottage, then you can make a stove from the bath with your own hands, which will be very expensive in the store. A material such as cast iron is excellent for creating a furnace, because it has such advantages as:

Great durability.

Excellent thermal conductivity.

Withstands even the highest indoor temperatures and humidity.

Easy to operate and does not require special maintenance.

Use old bath it is possible for the construction of such types of cast-iron stoves, such as: street, which will be in the garden, as a fireplace for country house, and, of course, for the bath. Such options can well be realized with the help of own hands.

Making a stove, how to properly prepare a bath?

You will not be able to fully use the container, so you will need to saw it. To make the cut correctly, you need to approach this issue with great responsibility. You will have to work with a grinder; you will also need to prepare several discs for metal in advance. It is imperative to take care of safety precautions, therefore, wear special glasses, a respirator and gloves. All actions must be performed correctly according to the recommendations given below:

1. Before you start sawing, you will need to make calculations and markup for the future cut.

2. The first step is to cut the enamel layer, this is done in order to prevent chips at the edges.

3. Directly the cast iron itself is cut in small pieces, while it is worth taking breaks.

4. When half of the bath is cut, it is required to substitute supports under both parts, which will not allow further damage to the tool, and the material itself.

Experts say that cutting is best done at an angle, then the enamel will not exfoliate much.

Rules for making a stove for a bath from an old bath

The process of making a stove for a bath is very complicated, because you have to take care not only of quality, but also of safety. The fact is that the stove will be located in the bathhouse, so there are parameters for the installation, for example, it is worth taking into account the thermal power and its change, the ability to produce steam, as well as the ability to regulate convection flows. As soon as the bath is sawn, you can begin to build a stove in the bath. You will need one half of your cut, but sometimes two parts of the tub can be used.

To properly build such a furnace, you must be guided by the following expert advice:

To make a stove on your own, you initially need to prepare a foundation, it is made from concrete mortar, sometimes a filler is used, broken brick is perfect for this, which is able to withstand even a large load.

One part of the bath is laid on the foundation, while it is important to make sure that it looks with the curved part up. The cut should be built into the wall with access to another room, where the heating of the bath will take place directly. For security purposes and for the purpose of implementation design idea, the hole closes brickwork, then the furnace and blower door is installed.

When half of the bath is installed properly, then at a distance of 10 centimeters, walls of refractory bricks are also erected, which will be equal to the height of the cast iron container. The space that forms around must be filled with stones, it is they who will warm the room to the desired temperature.

Alternatively, you can build an ordinary sauna stove, which will consist of two tiers, with all the heat going to the upper tier. The principle of operation of such a furnace is based on the passage of gas through the bath, due to which the stones are heated, and then the heat already flows down and returns up again, after which it is released from the pipe.

One cannot but agree that the decision to create a stove for a bath in this way at your dacha from a bath is creative, but it is also considered rational in terms of unnecessary costs. For construction, it is absolutely not required to use any material, except for an old cast iron bath, you can also make a stove yourself without involving outside specialists, of course, this option should be considered if you have at least some experience in building baths. It is important to note that another advantage is the durability of this equipment, because cast iron is a durable material that can withstand high temperatures and moisture, which means that you can enjoy a hot bath for a long time. In addition to saving money, you also get a durable oven in addition, which is difficult to find in the construction markets, because most materials today do not match the quality.

The cast iron bathtub made in Soviet times is durable, solid and very heavy. However, the once white enamel loses its former luster, and it is unlikely that it will be possible to restore it. It’s a pity to hand over the bathtub by the weight of scrap metal or drag it to a landfill. What else can you do with it? Some owners of country cottages and summer cottages suggest using this cast iron product with more benefit: DIY a stove from an old bathtub. Agree, this is original and rational. Such a stove will be able to decorate the estate and make it possible to prepare delicious dishes.

Required materials and tools

To independently build a stove from a cast iron bath, you will need to stock up on the necessary tools.

Here is an exhaustive list of them:

• grinder (angle grinder), as well as discs for it (stripping and cutting);
• electric drill and set of drills;
• equipment that allows gas cutting of metal elements (if any);
• spanners different sizes, hammer and pliers;
• crowbar and shovel;
• container where the solution will be mixed;
• spatula and trowel;
• instrument for taking measurements: building level, plumb line, tape measure, metal corner;
• welding machine (will be needed to mount the chimney), as well as electrodes to it and a protective mask;
• hacksaw for woodworking.

The main element of the furnace is a cast iron bath. However, the stove is heavy, so it must have a foundation. A certain amount of sand is required for its construction, cement mortar, bricks, as well as clay and water.

Making a stove from a cast iron bathtub is much cheaper and more profitable than buying a new one.

In addition, you will need:

• corner (metal);
• metal sheet (4 millimeters);
• lattice of a certain size;
• pipe required for the manufacture of a chimney (length - from 2 to 3 m, diameter - from 10 to 12.5 cm, wall thickness - from 3 mm);
• hinges for doors;
• rabitz;
• polyethylene film (necessary to waterproof the foundation);
• board (thickness - from 2 to 2.5 cm);
• slats (2 by 2 cm);
• nails.

Making a stove from an old bath with your own hands: step by step instructions

So let's look at how you can make your own stove from a cast iron bath.

For a country house, you can make a stove from an old cast-iron bath, which, in terms of its strength and service life, will not be inferior to models from the factory

First, we build the foundation.

1. Using a cord and stakes, we mark the foundation.
2. We dig a trench, the depth of which should not be less than 50 cm. We put layers of sand and gravel on the bottom, after which we carefully tamp them.
3. On top of the sand and gravel cushion, we put a waterproofing layer, as a rule, which is polyethylene.
4. To raise the base of the foundation, we construct a formwork in the center. Usually, a general formwork is built, and the pouring is done to a height of at least 30 cm.
5. The free volume is reinforced and filled with a solution of cement and sand (1 part of cement to 3 parts of sand). You can also fill the volume with brickwork.
6. After pouring the foundation, it must definitely solidify.

Now it's time to design the stove itself.

For this purpose, we perform the following actions:

1. We cut the cast iron bath across. This must be done carefully, since cast iron is very fragile. If the movements are inaccurate, sharp, you can damage the bath so that it becomes unusable for subsequent work.
2. We take half of the cut tub, after which we install it on top, and so that we get a structure that looks like a capsule with a cut.
3. Further, for work, you will need a sheet of metal with a thickness of more than 5 mm. For the construction, you will need two halves of the bath and a metal sheet, which is necessary to separate the lower part from the upper (the fuel zone from the place where food is prepared).

A chimney hole must be provided in the metal sheet, located close to the back wall. The chimney begins from the lower chamber, and then goes through the entire stove.

In order to securely fix the two halves of the bath and a metal sheet, it is advisable to use fasteners. To prevent smoke from the chamber located on top, a special sealant should be used, which is called an oven.

The chimney is attached to a metal sheet using welding.

1. We install the stove blank on the bricks. It is very important to align it to prevent the structure from falling. Before starting to weld, it is recommended to heat the cast iron a little (for example, the material will become much more pliable if the wood is heated in the chamber).
2. In the lower chamber, we close the front part with a metal sheet, making a large-diameter hole in it before that (firewood will be thrown into the chamber through this hole).
3. We make chamber doors for the firebox and for cooking.

Well, a simple and rather functional stove is ready. There is only one little thing left: to decorate the structure, making it a decoration of the yard. The stove can be painted, for example, in a folk style. No one would even think that a cast-iron bath was used to make the product.

Sauna stove from an old bath

A cast iron bath can be the basis of a good kitchen stove. However, it is quite possible to make an excellent sauna stove from it, and with your own hands.

Cast iron is an environmentally friendly material, so no harmful substances are emitted when heated

Building a bath and equipping a stove in it will require certain skills, so it makes sense to consult a professional before building.

TO sauna stoves certain requirements are imposed:

• All such ovens must have enough power (heat), and they must also have a wide range of its adjustment.
• To change the mode of heat and moisture, the device is equipped with a heat accumulator and a steam generator.
• The stoves should have the ability to adjust the convention.

So, from a cast-iron bath that has seen the views, you can make a simple two-tier bath stove that meets all the requirements listed above. The lower tier of the stove is one half of the bathtub, which is facing the wall with a cut and a convex part upward. The entire structure from the outside must be bricked. The required steam generation is provided by the stones that cover part of the "bath-furnace". Heat is accumulated in the upper chamber.

The principle of operation of the stove is quite simple. When passing through the cast-iron bath, the gas heats up the stones, then reaches the so-called bread chamber on the opposite side. Then the gas flow makes a "dive" (goes down and immediately up), after which it leaves the pipe. A damper is located at the bottom of the stove to prevent the emission of smoke.

Cast iron stoves: evaluate the benefits

Why is a homemade cast iron stove (in our case, a cast iron bath stove) so beneficial? Cast iron is among the best materials for this purpose, however, prefabricated cast iron furnaces are quite expensive. This material gained popularity due to its strength, although it is fragile. In addition, it is resistant to critically high temperatures and is unpretentious in operation.

Modern cast iron stoves are especially popular

Comparing cast iron and brick oven, let's say that the thermal conductivity is much better in the former. And since in the bath high temperature not constantly maintained, the material should not be sensitive to temperature extremes.

IN winter time the bathhouse at the summer cottage is usually not heated, which is why the brick sometimes begins to crumble, while cast iron is not aware of such problems. As for fire safety, only a new brick oven is absolutely not dangerous. With an old product, sparks may burst through cracks.

In order to increase the aesthetics, a do-it-yourself cast-iron bath stove is best lined with brick. If some units are damaged, they can be easily replaced.

Steel competes with cast iron. In terms of heating rate and strength, steel furnaces are not inferior to cast iron ones, however, the service life of the former is significantly shorter. Perhaps the main weak point steel furnaces are susceptible to corrosion. In cast iron, this problem is not so pronounced.

By making a stove from a cast iron bath, you will become the owner of a comfortable and reliable devicethat functions perfectly in all conditions. From such a bath, you can also make a very original fireplace for a summer residence. It is especially suitable for those who are now laying out the laying of a country house, since the fireplace, as it were, is "recessed" in brick wall, and this makes it possible to use the space with maximum benefit.

Video: Universal miracle stove from a cast iron bath

Having evaluated all the advantages of cast iron (for example, compared to steel) and the relative ease of making a bath from a cast iron bath, we note that it is very profitable to make a bath from this material on your own. So, if you want to make a stove from an old bathtub with your own hands, buy the missing material, pick up the tools and start!