Construction of a wooden slide. How to make a children's slide with your own hands - instructions for DIYers. Material for children's slide made of wood

Parents who have small children often have to visit playgrounds for the child to swing on a swing, play in a sandbox, or ride a slide. But adults do not always have enough time for such events, especially if the site is far away. Having your own plot, you can make such entertainment for your child at home. This will solve many problems of the parents, and the child will always play under supervision. Today we will talk about how a children's slide is made with our own hands from scrap materials.

A metal slide is a common structure from Soviet times. It was installed on the playground along with a sandbox. Metal is the strongest and most durable material. But under the influence of external negative factors, it corrodes, therefore, it is better to use stainless steel or galvanized metal to make a slide. When making a slide at home, you must have a drawing at hand.

From materials and tools you will need:

• metal pipes with a diameter of 15-25 mm, rods;
• corners with a section of 50x50 mm, 20x20 mm;
• galvanized sheet metal;
• multi-colored paints, cement, crushed stone;
• welding machine, grinder, scrap, hammer.

Having prepared necessary materials, at the site of the future installation, proceed to the manufacture of the structure according to the drawing:

1. Start manufacturing with the frame. For the upper platform from the corner, weld a 1.5 x 1.5 m square.Place stiffeners crosswise inside it. Weld a metal sheet with a thickness of at least 1 mm of the same size on top of the square to the corners. If possible, use corrugated iron, it will give stability, and the child will not slip on the platform.
2. Weld the finished platform to the racks. To make them, you will need a pipe with a diameter of 25 mm and a length of 3 m. Weld the heels from any metal scraps to the ends of the racks, the lower part of which will be concreted.
3. Under the welded frame, mark and dig 4 holes about 1 m deep with a drill. Tamp the bottom with small stones or gravel. Lower the frame racks into the pits, aligning the structure with a plumb line. Stir cement mortar with rubble and fill the holes. After about a week, the solution will completely harden and you can continue building.
4. For stability, weld the frame strapping between the posts from a 20 mm pipe for stability. From the edge of the platform down to the ground at an angle of 45 °, weld parallel to each other a descent from 2 corners with a section of 50x50 mm. Across the corners, weld at a distance of 20 cm from each other strips for steps from the corners with a section of 20x20 mm. Sew up the plane of the steps with wooden boards or corrugated iron.
5. On both sides of the stepped descent, weld on the handrails of 15 mm pipe. Sew up the openings between the handrails and the descent metal mesh or thin rods.
6. The chute is made of 2 pipes with a diameter of 20 mm. Bend the lower part of the pipes with a pipe bender or by heating with a cutter. You should have a construction of a steep descent, smoothly turning into a horizontal plane. Weld the upper part of the gutter to the other edge of the platform. Fix stiffeners between the pipes of the gutter. From above, weld on galvanized sheet metal with a thickness of at least 1 mm. If you cannot make a descent from solid galvanized steel, then weld on smaller sheets with an overlap along the descent.
7. Bend the sides of the gutter guardrail out of the 15 mm pipe. They need to be welded parallel to the bottom at a height of 30 cm, and the sides must be sewn up with galvanized sheet metal. Weld gutter supports from any remaining pipes in several places.
8. The metal structure is ready. It remains to process it with a grinder to remove all sharp protrusions. The design can be painted with multi-colored paints to make it attractive to the child. The bottom of the descent does not need to be painted, otherwise the coating will reduce slip.

Wooden slide

It is easier to make wooden slides at home yourself, no welding is required here. Wooden structures are less durable than metal ones, but wood can be used to make a beautiful playground with a sandbox, a house, rope ladders and other equipment. For DIY construction, it is better to use coniferous wood. From materials and tools you will need:

• 4 beams with a section of 100 x 100 mm, a bar with a section of 50 x 50 mm, an edged board with a section of 25 x 150 mm;
• galvanized iron 1 mm thick or linoleum;
• screws, nails, antiseptic, varnish or multi-colored paints;
• cement, crushed stone;
• electric planer, grinder, screwdriver, hammer, sandpaper.

Work, as always, start with drawing up a design drawing. Decide whether there will be a slide with or without a house, and draw a diagram of it. This will make it possible to calculate the consumption of material, as well as facilitate further construction.

Everything is ready, you can start carpentry work:

From the remnants of the material, make wooden benches or a sandbox near the slide. They will decorate the playground, bringing joy to children.

Plastic slides

It will not be possible to make a plastic structure on your own, they only buy it in a store. Such slides are produced in one piece and collapsible. The owner only has to install the slide on the site. Collapsible models are better suited for giving. It is convenient to disassemble them for storage in winter period... This will prevent theft and vandalism while the villas are left unattended by the owners.

In plastic models, different gutters are used, which children really like. They are screw, tubular, straight and other shapes. If the child still wants an unusual descent, and the parents do not have enough money to buy, it can be done for a summer residence or at home combined option slides. The point is that the gutters are sold separately. They are also made in any shape to order. You just have to make metal or wooden frame and attach a plastic escapement to it.

A playground built independently for a summer residence or a house will decorate the yard, provide children with entertainment in the summer.

In contact with

Slides, like swings, are one of the most popular outdoor activities for children. Any playground is equipped with a slide.

Recently, some parents are afraid to send their children to the site themselves, especially during rush hour. The slide itself is almost not dangerous and is equipped with a number safety devices... But the public slide itself is dangerous in the form of other children.

Imagine what would happen if several children climb a sufficiently high hill and decide to fly off the hill like a caterpillar? Often such experiments end in failure. Therefore, now some parents, whenever possible, restrict their children from such dangers and build similar slides in their yard, in the garden and even in the garden.

The only thing left to do is to design and build such a slide.

Types of slides and the age of the child

First you need to decide on slide view... There are a huge number of them: small, medium, very large, plastic, metal, double, with a whole range of additional features.

On playgrounds you can often find slides made of metal... This design is easy to mass produce and durable. Convenient when used by a large number of children.

But regarding security such a slide has several disadvantages:

• The height and the sharp angle of the slope make the metal slide dangerous for very young children.
• In the sun, the metal slope can reach very high temperatures.

In a relationship perfect combination slide size, relative safety and convenience the best option considered wooden slide... It can be like standard view, and with various additions in its design.

There are double-sided slides with space for rope and rope ladders. Such slides attract the attention of children much more.

And in the hot summer time, children will not mind playing on inflatable slide... The slope of such a slide ends directly in the pool with water. This slide can be used by children from three years old under the supervision of adults. It is not recommended to fill the pool deeply, especially if your child cannot swim.

Which material should you choose?

For the smallest children, slides are made of plastic... This design is a low ladder (usually no higher than a meter) and a plastic slope with the lowest possible angle of inclination for safe use by children.

But making such a slide on your own is impractical. Better buy finished product, given that the market can be found as the most budget optionsand more expensive ones.

The best material for self-made roller coaster is wood... The tree is flexible in terms of creating a wide variety of structures, not expensive and environmentally friendly.

Create a metal carcass roller coaster is a tricky business. Additional equipment, materials, skills are required. Therefore, those parents who want to pamper their children opt for a tree.

Some craftsmen successfully combine a slide from a wooden base and a metal or plastic slope of a suitable size.

It can be purchased from a hardware store, or ordered from the factory.

Making a slide out of wood?

Consider a wooden model slides for children 3-8 years old with a metal slope.

We will need:

• 12 base beams;
• several boards for the upper part of the slide;
• flat board for the ramp pallet;
• metal or plastic slope;
• 2 boards for the railing of the ramp;
• ladder boards;
• nails;
• plywood.

1. First you need to build base for the slide... The construction of our base will be the simplest, but at the same time it will be quite stable. It will be a rectangle one and a half meters high and a meter wide. To build such a rectangle, we need 4 one and a half meter beams and 8 meters.
2. We will find a free space in the garden or on any other site where we plan to install a slide. Let's get down to assembling the base... Assemble a square from four meter bars, firmly hammer it together with nails.
3. Now take one and a half meter bars and fix them perpendicular to the resulting square in the corners. Finish off the base using the last four squares for the roof of the rectangle. Base top cover with planks for added stability and safety.
4. Cut out squares of plywood to the appropriate size and nail them to the sides and top of the base. If desired, the resulting walls can be painted.
5. The next step is attaching the ramp to the base... To begin with, set the railing of the ramp at the appropriate angle so that the child does not fly to the ground during the game. The resulting sides must be at least 15 centimeters. Attach the base - a flat board under the railing.
6. Now install directly by yourself slope... The anchoring process is quite simple. Using a special stapler for metal, attach the ramp to a wooden pallet, pressing it tightly and evenly straightening it.
7. Then you can proceed to building stairs... Decide on the height of the child who will use this slide. Based on this, you can determine the most suitable distance between the steps of the stairs and the height of the railing.
8. Choose a convenient ladder angle... The smaller the angle of inclination, the easier it will be for the child to climb the hill.

The last part of building a children's slide is installation of handrails on the stairs and the top... They should be high enough so that the child feels safe and does not panic at the top of the slide. The wood intended for the railings must be sanded beforehand so that there are no knots and hints.

Simple wooden slide drawing

When building, keep in mind that it is better to make the slide "for growth" so that it lasts a long time.

On video detailed master class:

Do not hesitate to build a slide. This is a feasible task for most parents. This slide can be many times safer for your child. You will take into account all the nuances, combine safety aspects and find a compromise so that in the future you will not worry about how your child spends his leisure time.

Came out. What else to keep your children busy with on a walk in excellent winter weather? Offer to go for a ride on the hill and, taking with you a couple of ice floes, rather run into the fresh air!

Is there no ice slide nearby? What's the matter! Let's do it ourselves. It seems difficult the first time, but in fact those who have been riding for a long time have a lot of practical advice on how to make a slide out of snow.

Lesson plan:

The main thing is to prepare correctly!

Where do we start? No, not with the search for shovels and buckets! We will start with a friendly team, call the neighbors at the door and invite the kids, their daddies and mummies to a responsible task. The whole team, taking with us enthusiasm and excellent mood, we go out to survey the area. An important stage, by the way!

Choosing a place

We carefully examine the trees and pillars growing nearby, so as not to rest our forehead against them and not become the bearer of a huge cone.

Walking paths will also become a sports obstacle, you will have to carry pedestrians on your own. Better to choose another track.

Illumination is also important, as it gets dark early in winter, and it is completely inconvenient to ride with flashlights.

Have chosen a place - do not waste time, it was not in vain that we met. Clear the platform for the future slide from debris.

We select the size

The chosen location determines the height. The higher you conceive the slide, the more space it will require. Therefore, you have to proceed from the existing one.

Experienced parents advise to sculpt a slide according to age. If only for kids, then a height of about a meter is enough.

If you are going to ride with families, then you need to make it a little higher - about two meters. You need to calculate the length so that the angle of descent is no more than 30-40 degrees, otherwise it will look like a descent with a bungee - from a height with your head down. Traumatic, you know!

Well, the width can be any - for tubing, ice, experience smaller and larger, riding in a crowd or one by one.

The place was chosen, the height was determined. Now the question is: when?

We set the day

We pick up super trendy phones and open the weather. What is right for us?

An ideal option for construction is a thaw during the day and frost at night. So you can build a slide from easily succumbing sticky snow, and leave the ice beauty to freeze overnight with a calm mind.

You can be sure that there will be no surprise in the morning - the slide will not turn into a pile of melted snow.

If there is no suitable weather in the near future, then we proceed from the fact that the heavenly office will read us. There are two options:

1. or postpone until better times;
2. or start at zero temperature.

In order not to waste time, in this weather, you can create a base, sticky snow will settle and make the structure durable, and we will fill it according to the weather. Night frost for pouring - required condition... During a thaw, pouring water onto a hill is Sisyphean labor.

It seems that we have decided, now we are distributing among the friendly participants of the construction team who takes what out of the house.

Collecting tools

We are looking for houses that are, as we may find useful:

• wide shovels and large spatulas;
• insulated gloves with a rubberized top, if there are none, we do it simply: first, warm woolen gloves, large rubber gloves up;
• country watering cans, hoses, buckets, sprayers;
• everything wooden, flat and wide, that will serve for formwork and descent - panels, plywood, old countertops;
• mops and rags.

What exactly will be needed, you decide for yourself when you discuss the technology of construction and pouring. And how all of the above can come in handy, I will tell you in the options offered by the past practical course "Snow architects" parents.

Assembling in parts

A friendly team assembled, the weather is right, the mood is fighting. Let's get started. We will make the base. These are standard architectural approaches.

Little building tricks

Those that are more cunning are advised to turn on the fantasy!

Oh yes, I forgot! And what kind of slide do you mold? After all, you can be creative, with a twist. Well, for example, with turns in different directions, then you will ride like bobsledders.

It is possible with fairy-tale characters at the entrance in the form of an arch. And also with two separate descents - for those that are smaller and for those that are older.

Don't forget about beauty! Give the children paints and paint brushes, and you will see how your slide will bloom with snowflakes and patterns.

A responsible stage

Are you standing near your work of art and the eye is happy?

Now this snow mound needs to be filled with water in order to preserve and use it for its intended purpose. Here, too, there are some tricks, you need to approach the process deliberately, otherwise, with one movement of your hand, the slide turns ... And you have to do it again and in an amicable way!

Just take a bucket and pour out the water or pour it under pressure with a hose, especially if you use hot, - the first step is to ruin everything. There will be numerous pits and hills.

So which will fit?

If pits suddenly appear, do not despair. We fall asleep with snow and grind the defect. We knock down the hills and level them.

Place plywood or cardboard on the area in front of the ice path. And so that this material is not blown away by the wind and carried away after the skaters, coat the perimeter with a mixture of water and snow, it will fix your site overnight. Likewise with steps. Wooden slats or planks are suitable for them.

This concludes our main mission. We leave our slide alone for the whole night. Let her get bored, she has everything ahead!

A few touches to the portrait

In the morning we go outside and evaluate the result. We bring the descent to a perfectly flat surface using the same spatulas and a mixture of water and snow. We fill the slide again. This time you can do it in a big way - from a bucket or a hose. After one more night, your slide will be ready to receive guests.

I propose to take a picture of your ice miracle so that the children brag at school among their classmates. Yes Yes! Let the guys drag their parents out into the yard, and they will also have their own slide.

And you friends, when was the last time you built a slide of snow?

Or, when was the last time you went downhill?

Don't remember already? It happens that she herself is.

I propose to add an item to our diaries for the near future: "Ride down a slide with children"! And be sure to do it. Well, in order to motivate both you and myself, I propose to watch this video and remember how it happens when you fly from the mountain ... and inside everything freezes with happiness ...

That's all for me! And you? Are there additions on the topic of the article? Then share them in the comments. And also share the link to the article with your friends using the buttons of social networks.

Happy and interesting winter for you!

Always yours, Evgenia Klimkovich.

An obligatory element of any personal plot, if you have children, is a playground. Any number of structures can be installed on it. different types: sandpit, pool, swing - the choice depends on your desire and financial capabilities. Most of the items for the playground can be made by yourself. For example, a do-it-yourself children's slide is built quite simply, serving as a source of children's joy for many years.

Requirements for a children's slide

The children's slide can be installed both indoors and outdoors. It should be understood that a slide for a child (it is built for the house or for the street in this case does not matter) must meet certain requirements:

• for construction, only materials that are environmentally friendly and safe for the health of the child must be used. It doesn't matter if you are building a slide made of wood, metal or plastic, the material should not contain harmful elements. The same goes for paints and varnisheswith which you will open the structure. Another important point both for a children's plastic slide for the house and for wooden structure - it is resistance to fire;

• be sure to use structural elements such as railings and railings. They will not only help the child to maintain balance while climbing the hill, but also protect him from falling during games. Railings on a slide for a child in the country should be installed regardless of the age of your child;
• it is best to use wood for building a structure. Children's wooden slides for the home are more pleasant to use due to the natural origin of the material. In outdoor conditions, slides made of wood do not heat up as quickly as metal ones, so they can be installed in any place convenient for you, and not only on the shaded part of the site. On hot metal, a child can easily burn itself, but a tree does not heat up to a dangerous temperature;

• a plastic outdoor slide for children is lighter than a wooden or metal one. It can be easily moved from place to place, transported if necessary, but the material itself is less durable - it can easily crack;
• the slide should be located away from trees, lights, outbuildings and other structures. This is done so that the baby does not get hurt when going down the hill. The area around the slide can be sown lawn grass or use a special rubber coating. Remember that the main thing is the health of the child, therefore, any outdoor children's slide for a summer residence should, first of all, be safe;

• the base should be reinforced with a metal support or concreted. Do not rely on the fact that the child will not move the structure anyway - even the most durable slide can tip over as a result of children's games;
• an important point is the height of the children's slide being built for giving with your own hands. It should be appropriate for the age of the child, for example, the height of a slide intended for younger children school age, should not exceed 3.5 m.

Do-it-yourself slide construction: the necessary materials and tools

How to make a slide in the country with your own hands without much difficulty? If we are talking about a wooden structure, you will need several wooden beams, planed boards, battens, lining and fiberboard. You can connect the elements with each other using nails, anchor bolts and screws.

The list of tools required for construction is very simple:

• saw for wood, hand or electric;
• hammer;
• hand or electric drill;
• plane;
• tape measure and level;
• drill.

By the way, it is not necessary to use a wooden ramp - cracks or chips may come off on it, which can injure the child. You can buy plastic slides and mount them on a wooden structure.

In the case of metal construction, things are a little more complicated. Here you will already need a welding machine and a grinder for metal. All seams and joints in wooden and metal structures should be carefully sanded so that the child does not accidentally injure himself while playing. Metal slopes for a children's slide should be painted with a special paint that will absorb sun rays and do not allow the metal to heat up to high temperatures.

How to make a children's slide with your own hands: installation sequence

If you decide to create a slide for a child on your own, you should follow a certain sequence of actions:

• first of all, you need to prepare a construction plan. You can take a ready-made layout from the Internet or draw your own. Ready-made drawings of a children's slide made of wood with your own hands are good because they indicate the exact proportions of the elements and the sizes of individual parts;
• referring to the diagram, it is necessary to saw boards, slats and beams. In addition, they must be sanded so that splinters cannot get under the child's skin. With the help of a plane, the beveled edges of the corners of the parts are removed, which will further increase the safety of the structure;

• markup is carried out on the allocated area. It is worth allocating a plot with a margin if you are going to build a children's sports complex for a summer residence along with a slide. Optimal size for a structure without additional extensions - 2 by 2 m;
• grooves of about 60 cm are dug under the supports. wooden beams, the ends of which should be covered with a special waterproofing mastic. This is done in order to extend the life of the supports. In the racks, grooves are cut into which the connecting wooden planks... The elements of the resulting frame are connected to each other using bolts or self-tapping screws;

• then the floor is mounted. When building a slide with your own hands for children, remember: it is important that the floor is as strong as possible, therefore thick boards are selected for it, which are connected with self-tapping screws and screwed to the frame using metal corners. If you do not want water to accumulate on the floor of the slide, small gaps should be left between the boards, but not enough for a child to stick a finger in them;

• a ramp for children's slides is made. Its width should not exceed 80 cm. The surface of the slope is covered with linoleum, galvanized sheet or plastic. Linoleum is the cheapest option, but it deforms and comes off easily. The metal coating heats up significantly in the sun and can also bend. The most reliable option is plastic slides for children's slides. Plastic does not overheat, does not rust or bend, but it is more expensive than linoleum or metal;

• the staircase is mounted. The optimal size of the boards for making it is 20 mm. After mounting the main part, the side part is installed. For this, the board sawn at an angle of 45 ° is attached to the racks using screws. Then the bars are screwed to the board, on which the steps are mounted. Photos of children's slides with their own hands made of wood on the Internet clearly show how exactly you need to fasten the elements of the stairs. After the installation of the steps, balusters are installed on which the railings are attached;

• grooves are cut in the side of the racks, into which the side walls of plywood or fiberboard are installed. The walls can also be made of small boards or have some original look;
• all protruding corners, heads of nails and screws are removed, all surfaces are carefully sanded and covered with paint or a special protective varnish.

Drawing of a children's slide for a summer residence. dimensions: length - 3020 mm; width - 890 mm; height - 1800 mm. Maximum user weight - 100 kg, minimum child age - 3 years

An interesting design modification can be a slide - a sandbox for children. In this case, the sandbox is organized either at the base of the slide, or you can build a tank with sand at the end of the descent.

Features of using different materials to build a slide

If you are in doubt of what material to build a house with a slide for children or another similar structure on personal plot, you should familiarize yourself in detail with the features of buildings made of the two most popular materials - wood and metal.

Pros and cons of wood slides

Wooden structures for playgrounds have proven themselves well several centuries ago. All children's slides with their own hands made of wood are built according to the classic layout, which includes a ladder and a ramp, a base, an upper platform and a protective part. In addition, additional elements are often added to a typical project, for example, an internal labyrinth, a sandbox, additional slopes and much more. Since such a structure can be made quite simply, it all depends solely on your imagination.

One of the significant advantages of creating a wooden slide for children in the country with your own hands is the low cost of manufacturing. The material itself is relatively inexpensive, and specialized tools are not needed to process it. In addition, the construction of a structure from planks and beams does not require special building skills and abilities from you - sometimes it is enough just to strictly adhere to the scheme found on the Internet.

Another plus of this design is its environmental safety. The tree does not cause allergies, does not emit harmful substances when heated. The only controversial point here is the paintwork of the building, so be sure to read the instructions when buying varnish or paint to cover the slide.

An element that should be given special attention when installing a wooden structure is the descent. It is best not to risk using your own planed boards, but to purchase material for a factory-made ramp. It can be linoleum, stainless steel sheet or plastic. The latter option is the most expensive, but also the most reliable and durable.

Advantages and disadvantages of metal construction

Metal slides for children used to be in every yard and, with proper care, could last for more than a dozen years. Photos of children's slides made of metal with their own hands show that in appearance they differ little from their wooden counterpart.

A significant advantage of a metal structure is its strength. The iron structure does not require special processing and maintenance, it can withstand temperature extremes, high humidity, and large mechanical loads. The only thing that needs to be done periodically with the metal slide is to renew the paint and make sure that the paintwork does not peel off as a result of corrosion.

How to make a slide for children with your own hands from metal? To do this, you need ready-made elements, a grinder and a welding machine. Particular attention should be paid to the seams, as they are potentially dangerous for the child. Welding quality is also of fundamental importance: the higher it is, the stronger the structure will be.

The disadvantage of an iron slide is that it warms up quickly in the sun. If you install such a structure where the sun's rays constantly fall on it, your child can easily burn himself. Therefore, if you nevertheless decide to build a building from metal elements, you should choose a place for it in the shade or make a special canopy.

When building a slide with their own hands for children, it is not necessary to use only wooden or metal elements. These materials can be combined in different proportions, thus obtaining an original, reliable and durable design.

Of course, you can always ask yourself about where to buy a children's slide for the country. This can be done in any specialized store or via the Internet. But remember that only a self-made design will satisfy all your requirements and allow you to realize your design fantasies.

There are a number of points that should be considered in order for the design to be reliable and safe:

• for additional stability of the balusters, the staircase of the wooden structure should be additionally reinforced with slats;
• do-it-yourself drawings, videos, photos of children's slides in the country house show that the grooves and the slats inserted into them, when bolted with bolts, form a light, but strong and stable structure;

• an excellent option for painting buildings is acrylic paint. It is safe for the child's health, protects the tree well from all kinds of negative influences and looks attractive. Also, acrylic is famous for its durability and does not lose color saturation even with prolonged exposure to direct sunlight;
• a convenient type of covering for use under the hill is artificial grass or rubber. Such a coating does not require special care, does not change its properties depending on the season or the weather, creates a safe surface under the hill that will protect the child from injury in the event of a fall from the hill.

A plastic slide for children purchased in a store or in the construction market is not always the best option. Yes, you save time and effort by building, but a wooden or metal structure can not only cost less money, but also allow you to create a full-fledged sports complex for a child, consisting of a large number of elements. By the way, even a plastic slide for children for a summer residence can be supplemented with homemade elements and turned into a complex and exciting structure for games.

A high-quality and reliable slide is not only good way keep your child busy while in country house, but also the ability to develop it physically. As the child grows up, the slide can be completed, improved and more and more stimulated the child to a healthy lifestyle.

For full physical development, children need sports equipment and facilities. The simplest is the children's slide. Many parents can build it with their own hands, both in the yard and in the apartment. This article will be a good help for novice masters.

Hill on the site

Downhill skiing has always been a favorite children's entertainment. Many people build it from snow in winter. But with the onset of heat, it becomes unusable. And the very transitional period of melting can sometimes lead to injury.

Therefore, it is best if a children's slide is built for giving with your own hands entirely of wood. You can build it using a boardwalk laid on metal structure... It should be noted that such a children's slide can last longer. With your own hands, drawings of such a design can be made based on this figure.

Slide as part of a children's house

Very often, on the sites, children are equipped with a real town. The playhouse, equipped for the entertainment activities of kids, can have an additional slide in the form of a slide. Such a structure is especially interesting if the building is installed on piles.

To build a slide from the house, you will need a flooring and two sides. Optionally, you can use a small platform before the descent. But it is successfully replaced by the veranda of the house or its threshold in the case when the slide is attached directly to the entrance to it.

You can also make a slide in a house set on the ground. True, then the solution will be quite original, extraordinary. In this case, the upper part of the descent should be fixed to the "attic" window or even to the roof. The kids will like the option of rolling directly from the windows of the house or from its balcony.

It's very important to take care of your child's safety! Therefore, it is worth carefully considering the ascent to the attic or the roof of the house. It is imperative to make a railing on the roof so that the kid cannot fall off during the game. The roof should also be flat, without any slope.

Do not pave the area around the hill and playhouse... It is best to shield it with a low side and cover it with sand. This will help to avoid a lot of troubles and make the place less traumatic. Of course, with this option, cleaning in the home will be significantly added, because children will constantly carry sand to rooms on their toes and feet.

Actually, if you wish, you can adapt the slide-descent and on the usual country housedesigned not for games, but for the whole family. It is convenient to do this when the house is on stilts and has a high porch. Then the slide is made by covering part of the stairs with boards. It is necessary to install a small side on the side of the slope, protecting it from the steps.

Stairs in the house and children's slide

It is not difficult to build an original descent from one floor to another with your own hands. Moreover, such a design move will be a creative solution to the problem of children rolling on the stair rail. Such a children's slide, attached to the stairs with their own hands, is both original, interesting and beautiful.

This is done in this way.

Two identical boards will serve as the side parts of the slide. The third board will be its base. Having knocked off a structure resembling a gutter, the edge should be cut off at the desired angle. The sharper the angle, the flatter the children's slide will become. With his own hands, the master himself will be able to adjust the slope.

One of the side parts of the slide should act as a bearing rack to which the steps are attached. The other end of the steps can also be supported on another supporting wooden post. But there is an option to mount them directly to the wall.

The slide is like a descent from the second tier of the bed

An interesting design version of the children's corner, which includes a sleeping place on the second tier. It can be a children's slide made of wood with your own hands and attached to sleeping place... Of course, the usual staircase must also be left.

To build an additional slide, you will need three boards: directly the lower part for rolling and two side boards that will play the role supporting structure... They are hammered together in the form of an incomplete parallelepiped from three sides. The lower edge of the bearing sidewalls is cut at an angle. They are subsequently placed on the floor. The upper edge of the sidewalls is also cut off, but the cut should be perpendicular to the base. This slice is attached to the side of the bed.

Details of the simplest toddler slide

Such a structure is suitable for kids to play both in the fresh air and in the house. Such a children's slide is made with your own hands from wood. Part drawings are not dimensioned. They can be selected arbitrarily.

But one rule should be strictly observed: equality of sides of some details.

The width of the upper platform (2) before descending must match the width of the side posts (1). The same size should be at the very descent, as well as at the lower struts between the posts, which give the structure its rigidity. Most likely, the length of the steps will correspond to it.

The bevel lines at the sides of the stairs (top and bottom) must be parallel. The same is the case with the slope lines at the side edges of the descent.

Fastening the simplest slide

The installation of the structure should be considered. If you make a do-it-yourself outdoor children's slide made of wood, the drawings of which are presented here, then metal pins should be attached to the side lower cut of the racks, which are best dug into the ground or even cemented from below by making a foundation. The structure used in the apartment can be rigidly attached to the wall with one side post.

Instructions for assembling a slide from finished parts

Before making a children's slide with your own hands, you should choose quality material manufacturing. Boards should not have cracks, knots, irregularities, they should be of sufficient thickness.

The connection of parts can be done using metal corners and bolts.

• First, the upper platform is attached to the racks at the required height before the descent.
• Then the bottom of the racks should be fixed with spacers. They are nailed to the lower parts of the racks parallel to each other.
• Separately assemble a staircase from steps and sidewalls. It is worth considering the fact that the sharper the cut angle of the sidewalls, the flatter the staircase will be.
• The upper part of the ascent is attached to the platform before the descent.
• Also, a slide is collected separately. To do this, the sides of the descent are fastened with a groove to the descent part. And here it is worth remembering that the duller the cut angle of the sides, the steeper the slide will be.
• The upper part of the descent must be fixed end-to-end to the upper platform.
• The entire structure should be treated with an anti-corrosion agent, painted, varnished.

The construction of the slide will take very little time, but it will bring great joy to the kids! And if adults manage to attract a baby to work, then the educational effect will not be long in coming.