Do-it-yourself upholstery of a wooden door with dermantine. How to sheathe a door with dermantine with your own hands? Video: Upholstery of a metal door with its insulation

Additional advantages of leatherette-covered doors are improved sound and heat insulation.

The appearance of entrance and interior doors, even with good care deteriorates markedly during use. If the product is still durable and able to last for a long time, then upholstery of doors with dermantine will help to correct its aesthetic properties. This well-known finish door leaf has additional advantages in the form of increased sound and heat insulation.

Dermantin has a rich color range

What special qualities does the material have that allow the door to be covered with leatherette for both street and interior structures? In fact, the list of positive qualities of leatherette looks impressive:

Humidity resistance. A street door upholstered in leatherette will not have to suffer from rain: water drops easily roll off the surface of the material. With the same success, its waterproofing properties keep the insulation layer intact.
Immunity to ultraviolet radiation. While most paints and varnishes fade mercilessly under the sun, leatherette retains its decorative qualities unchanged.
Frost-resistant properties protect door upholstery from deformation.
Resistance to harmful microflora. Sheathing dermantin is not subject to rot, mold, or mites.
Neutral attitude towards chemical cleaners. If upholstery front door leatherette is very dirty, it can be cleaned with any means.
Large variety of colors. The material is presented in such a wide range of shades that it will not be difficult not to choose an option that is in harmony with the interior.
Durability. Leatherette retains its performance properties for 7-10 years.
Affordable price is not the most important, but still a pleasant fact that only increases the popularity of the material.

When all are listed positive properties upholstery material, it would be dishonest to remain silent about its shortcomings. Although they are few, they are still there:

Relatively low strength. It cannot be said that leatherette needs very careful handling, but, by and large, it is a fabric, albeit a very dense one. You can cut it without much effort, and with very rough handling there is a chance to tear the upholstery.
Problematic repair. Cuts or tears on such a surface cannot be fixed, therefore, if the material is damaged, there is nothing left but to sheathe the door with leatherette again.
Fire susceptibility. In case of fire, it ignites easily, and since the door is upholstered with leatherette, this can lead to blocking the exit from the burning room.

What to look for when choosing a door upholstery kit

For the upholstery of the door, you need to prepare tools.

The standard set for upholstery of doors consists of leatherette, insulation and decorative nails. How to choose right stuff to make sure it lasts for a long time?

Leatherette must have high density and have elastic properties. Be sure to pay attention to its smell - if it is sharp, gross violations of technology are not excluded. Such material may evaporate harmful substances, which means that it is not suitable for interior decoration.

Heaters - isolon, batting, foam rubber. If you choose based on the lowest cost, this is foam rubber. It has a low density, so when finishing decorative trim forms a beautiful pronounced relief. If the insulation must provide heat and sound insulation, isolon is best suited for this task.

Upholstery of an external or interior door with leatherette

Sheathing a door with dermantine with your own hands is not a very difficult task. To begin with, prepare necessary material and tool. This list is compiled depending on how the door will be upholstered. But the required components of the list will be:

leatherette;
insulation;
scissors, sharp construction knife;
hammer;
construction stapler;
roulette;
decorative nails.

Traditional door trim

The door leaf is laid on a flat horizontal surface.

First you need to prepare the door leaf. It is removed from the hinges, the fittings are unscrewed, dust is swept away, dirt and grease are cleaned. Before starting the main work, you can immediately prepare the rollers, which will further ensure the insulation of the doorway. For a door that opens into the room, 3 rollers are required, and if outside, then 4. The length of the roller must correspond to the parameters of the part of the door where it will be located, and the width is such that it is possible to lay the insulation roller inside and fold the tape in half lengthwise. For attaching the roller to wooden door It will be convenient to use a construction stapler. On iron door the roller will have to be glued. Insulation is laid in the same way: the canvas cut to size is glued or shot with staples.

Then comes the turn of leatherette. The method of its installation depends on the door.

Metal doors need glue. First, it is evenly distributed with a brush along the perimeter of the door leaf and a lining is glued to this line, on top of which leatherette is laid on a new layer of glue.
Leatherette is attached to a wooden door with a decorative nail.

The final stage of work includes the installation of fittings.

A special way for the lazy

Covering the door with leatherette, without removing the door from the hinges.

This method is called so because the upholstery of the door with dermantine is carried out without removing the door from the hinges. This is especially convenient if the weight of the door is large, which makes it difficult to remove. At the same time, sheathing the door with leatherette on weight is a very inconvenient task.

The beginning of work looks the same as in the previous case: the fittings are removed from the door and cleaned. Then the roller is mounted: the prepared leatherette tape is laid along the edge of the door leaf and fixed with a construction stapler or nails every 15 cm. At the next stage, a sheet of foam rubber is shot with a stapler. The leatherette sheet should have reserves of 3 cm on all sides. They begin to fasten it from the center line of the top of the door. Carefully stretching, it is nailed around the entire perimeter. Now it's the turn to return to the formation of rollers, the blanks for which we had nailed at the very beginning. To do this, roll up a long roller, lay it along the edge of the door leaf, wrap a strip of leatherette and, twisting the edge inward, nail it with decorative nails every 10 cm. After the fittings are installed, the work is over.

Door upholstery with dermantine using a frame profile

Door trim materials

This method allows you to create almost any, even the most intricate pattern on the upholstery, since the markings for placing decorative nails are made directly on the surface of the door.

Additional details should be included in the door upholstery kit: a one-sided frame profile, which will ensure uniform tension of the fabric, and decorative furniture buttons with a top trimmed with leatherette. These buttons are unscrewed into two separate parts, one of which will be on the door leaf, and the second on top of the leatherette.

After dismantling the fittings and cleaning the door leaf, it is necessary to start marking the lines on which the lower elements of the furniture buttons will be located. With the help of a ruler and a square, we determine the necessary points and generously drip assembly glue on them. Glue the threaded button elements to the surface. We measure the sides of the door and cut the profile according to the measurements obtained. We put it on construction glue around the perimeter of the door leaf. Now you have to wait until the glue dries - it will take about a day. In order not to waste time, we are preparing the insulation: we need to prepare the holes for the buttons.

After a day, we continue the upholstery of the door: we lay the insulation in such a way as to align the holes with the threads of the buttons. If there is excess material that protrudes beyond the edges, they must be cut off. Now it's dermantin's turn. We carry out exactly the same procedure. Now, when all the threaded pins are located in their sockets, you can screw on the decorative hats, after which the leatherette, evenly pulling, is tucked into the profile.

This completes the door trim. After installing the fittings, the canvas is hung in a permanent place.

Tiled upholstery method

Door upholstery with chopped leatherette

Fine painstaking work, but the result looks amazing. It is made from dermantin cut into rhombuses. As a rule, the door is sheathed in a single color scheme, however, this method is good because creative people can experiment and create interesting ornaments on the surface of the door.

For this option, on the surface of the door, you will have to perform more complex markings: draw them into diamonds of the same size. In the corner of each rhombus, we put the lower element of the furniture button on the glue and set the door leaf aside for a day. Like last time, we make cuts on the insulation, cut the leatherette into rhombuses a little bigger size than markup. A day later we return to the door. We lay the foam rubber in accordance with the prepared cuts, perform additional fastening with a stapler along the edge and door leaf (3-4 brackets around each pin). We start laying out rhombuses around the perimeter. We bend the edges of the blanks and shoot them with a stapler. It is necessary to ensure that in the process of upholstery on the dermantine there are no distortions.

How to sheathe a door with dermantine so that it is not only durable, but also beautiful? We have offered several options, choose your own, which you can implement, and the result will be stunning.

03.09.2016 39871

The front door not only protects the house from burglary, but also keeps it cozy and warm. Upholstery of the front door will help increase its functionality, and in some cases even avoid replacement (if there are only cosmetic defects).

The modern construction market offers a lot of variations of upholstery materials of different prices: leatherette, vinyl leather, genuine leather, special fabric. The choice depends not only on the budget, but also on the type of door leaf, its quality, and the preferences of the owner.

Benefits of front door upholstery

Increasing the level of sound insulation, moisture resistance.
Improves an esthetic look, does imperceptible defects.
Keeps the heat in the room.
Protects steel sheet from corrosion, and wood from the effects of temperature changes.

But it is also important to take into account that the upholstery is sensitive to sudden changes in temperature and is practically unsuitable for restoration after mechanical damage.

How to upholster a wooden door

The upholstery of the entrance wooden doors will extend the life of the wood, prevent it from drying out. In the process of work, materials such as:

dermantin;
vinyl leather ( , beautiful appearance);
felt;
plastic-foam;
bologna fabric

When choosing a material, take into account which way the door opens. The way of working with sealing rollers and fixing the upholstery boards depends on this:

opens outward (the rollers are fixed to the ends of the door frame);
opens inwards (rollers are attached to the door frame).

To: material, insulation (batting, synthetic winterizer, isolon, foam rubber with a thickness of at least 2 cm), repair tools (special nails, tape measure, scissors, hammer, screwdriver, stapler). For 1 m² of area, you will need 50 g of construction nails and 75 g of decorative ones.

Upholstery kit, but also additionally warm the room.

Entrance door upholstery: operation algorithm

Measuring the door leaf, preparing it and segments to mask the edges. Measurements are taken with a tape measure. To create blanks from the material, two strips are cut equal to the width of the door and one equal to the length. The width in both versions is 14 cm. Then the canvas is cut along the perimeter 10 cm larger than the measurements of the door. It must be removed from the hinges and the fittings dismantled.
Removal of old material, surface cleaning (with special washes, spatula).
A heater is placed on the door leaf, the upholstery material is fixed with decorative nails, a special band for the edges. First, the side segments are fixed with nails with an edge (wrong side out). The lower part is nailed no less than 2 cm from the edge so that the material does not rub off too quickly. Each step of the sheathing of the canvas is 10 cm.
To provide additional noise and heat insulation, in addition to standard upholstery, it is recommended to install a sealing roller around the perimeter of the box, an additional layer of foam rubber, padding polyester on both sides. Sealing rollers are placed on the side segments of the material, the edges are tightly wrapped inside. On the edge of the fold they come with decorative nails. If the product opens inward, the rollers are attached to the ends of the door frame.
They make holes for locks, eyes, bend the edges and fasten them with nails.
The product is hung on loops.

The upholstery is stretched so that there are no folds or wrinkles. To do this, the material is fixed with a nail, first from above, then from below, carefully straightening, and only then the side part is fixed.

For decorative design use a silk cord, wire, stuff special nails in the form of a pattern.

If plastic (fabric) is used, then another technology is used. The main tool in the process of upholstery with this material is rectangular profile strips with a special slot. A decorative baguette frame is inserted into it and its coals are sawn off at 45 °. The frame is fixed with nails (indentation 7-10 cm), insulation is placed and covered with plastic, which is fixed with nails at a step of 4 mm.

Metal front door upholstery: process specifics

Entrance metal doors are upholstered using laminated fiberboard (for interior decoration), vinyl leather, leatherette.

For work you will need:

upholstery;
plywood;
stapler, scissors;
insulation (the thickness should be 10 cm more than that of the door leaf);
plywood;
liquid Nails.

Sequence of steps

First you need to remove the fittings, for convenience, the door leaf is placed horizontally on a hard, flat surface.
Plywood blanks are attached to the surface using epoxy glue. Complete drying is expected for at least a day.
To prepare the fasteners for the sealing rollers, first cut blanks (10 cm wide and length according to the door parameters) from the selected material. They are folded in half, fixed with nails or a stapler at a step of 10-15 cm.
To upholster the door and prevent heat loss, foam rubber is placed on the canvas, 2 layers of batting (attached with liquid nails).
The upholstery material is cut with a margin of 3 cm on each side, fixed above the insulation, first from above, and then from below with furniture nails.
Fix the edges of the sealing roller filled with batting.

Upholstery without interior trim requires additional manipulation. The workpiece is cut out from a solid fiberboard, holes are made for the peephole, a lock and placed on the insulation blocks. The panel is attached to the frame with self-tapping screws.

The upholstery is economically beneficial and in terms of the functionality of the door (the material will last a long period of time, save the room from noise and cold, beautifully decorate the canvas).

If the product is one-piece, and the sheets of the inner and outer skin are welded to the frame, then the foam rubber is fixed on the sheet of the inner skin. A frame of slats is attached to it with screws, between which foam rubber or batting is placed, covered with a fiberboard panel. It should be borne in mind that with this upholstery method, the thickness of the fabric will increase significantly.

First of all, they are recommended to those who want to increase the level of heat in the house, to ensure good sound insulation. It is better to use its modern analogue - vinyl leather. It has properties that are useful in terms of functionality and care: it is not afraid of frost, practically does not fade, it has an elastic and at the same time strong texture, and high wear resistance. There are many models on the market and color solutions this upholstery material. But the owner must also remember about the shortcomings: sensitivity to mechanical damage, temperature changes.

Door upholstery cost

Upholstery replacement metal door costs about 1500 r. for one side, wooden - about the same. The material is paid and purchased separately. The cost of working with doors of a non-standard size (not in the format of 200 by 80 cm) must be specified individually. Finishing with laminated panels is estimated at an order of magnitude more expensive - 4500 rubles.

The price largely depends on the materials used, the range additional work, adjustment of locks, ). For example, the average cost of a standard set: dark-colored leatherette, synthetic winterizer or foam rubber, decorative nails, glue is 1000 rubles, and the departure of the master is 500-800 rubles. On average, he spends 2-4 hours at work. But on sale there are ready-made kits for upholstery of entrance doors with your own hands from 200 rubles. Upholstery of doors with leather will not only decorate them, but also allow you to keep the room warm and quiet.

It is important to remember that upholstery of entrance doors with leatherette, for example, in most firms, provides only for fixing the material itself. And the installation of a sealing decorative roller, insulation with an additional layer of foam rubber, batting, isolon, vibration isolation must be paid separately (from 200 to 1500 rubles, depending on the type of work, materials used).

In addition, they require a fee for the preliminary departure of the master to measure and select the material, dismantle the old coating, install and remove locks. It is much more profitable to change the upholstery of the front door on your own, especially since this process is not very complicated.

Underwater rocks

When pulling the material, you need to carefully monitor that it is fixed correctly, without wrinkles and folds. If there is no experience in this kind of work, you can spoil the material or carry out this stage of poor quality.
It is not necessary to insulate with materials popular among the people (paper, felt). They do not retain heat well and contribute to the appearance of pests.
Cutouts under the eye, the lock should be smaller than the fittings.
When working with the upholstery of a metal product, it is important to ensure that the material of the inner and outer upholstery does not overlap at the gluing points. Otherwise, the fastener will be of poor quality.
It is better not to use rubber gaskets for sealing joints, this will interfere with the quality closing of the door.

Upholstering the front door is much cheaper and easier than replacing, and the alternative in the form of installation decorative panels from the MFD is not cheap (about 3500 without the departure of a specialist for measurement). Another plus of this design is warming and positive changes in the interior.

Do-it-yourself upholstery of doors will save money and be sure of the quality of the work performed.

Sooner or later there comes a moment when the front door loses its presentable appearance during operation. Of course, you can replace it with a new one, but if the structure itself is still strong and reliable, it is better to get by with cosmetic repairs, especially since covering the door with a finishing material will cost much less.

If you follow the technology, it will not be difficult to sheathe the doors yourself. Consider the features of finishing wooden and metal doors, as well as the nuances of choosing materials for them.

Choosing a material

The range of finishing materials for doors is large and they all have their pros and cons. In order not to get confused and choose the right one, we suggest that you familiarize yourself with brief characteristics the most popular ones.

Vinyl leather

Vinyl leather is an economical alternative to natural leather

This material is one of the varieties of artificial leather. It is a film applied on top of a fibrous web. The basis for vinyl artificial leather can be paper, knitwear or other fabric, which is usually impregnated with special polymer compounds to increase strength.

The material can have different colors and textures, in addition, it has an affordable price and is practical to use. Therefore, vinyl leather sheathing is a good replacement for natural, very expensive material.

clapboard

Lining - these are slats made of wood, MDF or plastic, equipped with special grooves that make it easy to assemble them into a single canvas. It is suitable for finishing both wooden and metal structures, however, it is much more difficult to mount it on the latter.

For the outer part of the door, it is preferable to use a material resistant to external influences, for example, larch. A more budget option is plastic, which also endures moisture and is not subject to corrosion and decay. But keep in mind that such panels can fade in the sun, so upholstery of doors with plastic clapboard will be unprofitable if they are often exposed to direct sunlight.

Lining from wooden slats

Faux leather

Leatherette is an artificial material that mimics the structure of natural leather. In addition to its attractive appearance, it has other advantages:

strength;
profitability;
simple care.

The disadvantage is sensitivity to temperature extremes and high humidity, which leads to cracking and thus reduces the life of the coating.

Leatherette

The name of this material comes from the Greek word "derma", which means skin. In construction terminology, dermatin is usually called leather imitation. Surely many have heard of him. But why is this material so popular?

The prevalence of leatherette for various finishing works explains it positive qualities, such as:

Also, leatherette is easy to process and stack, which allows you to work even without special skills. An additional plus of this coating is vapor permeability, which means that the door under the skin will be able to "breathe", which means that the wood under it will not become damp and moldy.

Genuine Leather

The door, upholstered in genuine leather, looks luxurious and emphasizes the viability of the owners, which is appreciated in some circles of society. In favor of the leather coating is also evidenced by:

material durability;
good sound insulation;
additional protection against heat leakage.

Leather is the epitome of luxury

But the price of such upholstery will be several times higher than that of various substitutes. Another nuance that should be taken into account is the need for careful skin care using special products to maintain its elasticity.

PVC film

Polyvinyl chloride film, which usually has a self-adhesive backing, is very practical and inexpensive material. The top layer of this coating can imitate various textures: stone, wood, velor, metal, etc. Such a film is sold in rolls and is a good way to update the surface of a metal or plastic door. Its main advantages:

undemanding to care;
small price;
simple installation;
moisture resistance;
no damage during installation on the glued surface.

True, there are several disadvantages - the inability to hide serious defects in the door leaf and a relatively short service life.

PVC film allows you to imitate any material

The listed materials are the most commonly used for upholstery and among them there is sure to be a solution suitable for your home. Of course, the final choice depends on your preferences, financial capabilities, the condition of the door and the material from which it is made. Given that correct installation coatings are no less important than the right material, below we will consider several ways of sheathing metal and wooden doors using the example of lining and leatherette.

Leather upholstery

So, how to sheathe the door with leatherette with your own hands? The process has some differences for wooden and metal structures, however, the preparation and necessary tools in both cases are almost identical.

Upholstery preparation

Dismantling the door

To independently carry out the installation of the coating, you will need the following tools:

sharp stationery knife and large scissors;
industrial stapler;
hammer;
pliers;
screwdriver;
brush.

Before starting work, you will need to dismantle all fittings from the door (peephole, handles, lock). Then the structure is removed from the hinges and inspected for any defects, if any, they must be eliminated.

Next, the leatherette should be cut to the size of the door, making an allowance of 10-15 cm on all sides. In addition, you can not do without cushioning material, which will give the upholstery the desired volume. If the door is not located inside the dressing room, but goes outside, then it is advisable to take care of its insulation. This function can be performed by the following materials:

isolon tape - has a long service life (about 70 years), is effective, but quite expensive;
foam rubber - can last about 15 years and has average heat retention;
batting - the service life is 30 years, it has good performance, but somewhat makes the door structure heavier.

Wooden door upholstery

Fixing the material around the perimeter

The upholstery process begins with laying a heater cut to the size of the structure on the prepared door leaf. The material must be fixed with a construction stapler or nails; before that, it is worth lubricating the surface of the door with glue for a stronger fixation.

Next, comes the crucial stage of fixing the upholstery. To do this, it is better to use special decorative nails, matched to the color of leatherette or the rest of the door hardware. The upholstery fabric is laid in such a way that the overlap on all sides is the same. Then the edges are folded inward, monitoring the uniformity of the fold of the fabric and its tension. Now it remains only to fix the leatherette with nails at regular intervals along the perimeter of the door leaf.

After the fabric is securely fastened, you can give the coating a pattern using decorative tape and upholstery nails. Ready-made patterns of the pattern are shown below, but you can also invent something new, focusing on your taste and imagination.

Schemes for decorative fastening leatherette

Upholstery of a metal door

The upholstery of a metal door is made a little differently, but this process is even simpler than in the case of a tree. After all, you don’t have to nail leatherette to the metal, and it is this part of the work that is the most time-consuming.
After preparing the canvas, which is identical to that described above, the door is removed from the hinges and placed in a horizontal position. The insulation is attached to the metal with glue, trying to lay it correctly the first time in order to avoid further displacements.

Then, leatherette itself (part of the material with an overlap) is attached to the ends of the door, smeared with glue. It is better to start from the top, then fix the material from the side of the hinges and the lock, and complete the installation with the bottom end. In this case, it is important to avoid the occurrence of folds and distortions.

After the glue dries, use a sharp clerical knife to remove excess material and install the fittings back. Cutting holes for door handles, lock and so on, do not forget that the slots must be smaller than the dimensions of the fittings. Otherwise, the holes may become noticeable and spoil the appearance of the structure. This completes the work, and your front door not only looks updated, but also provides additional heat retention in the house.

Finished construction

Clapboard door lining

Another way to inexpensively and tastefully update the door structure is to make doors from lining with your own hands. Where to start? For wooden panels, the following advice is relevant: if the finishing material you have stored outside the house, but will be used for interior cladding, then a few hours before the start of work, it is worth bringing it inside the room in which the decoration is planned. This will allow the wood to adapt to the humidity and temperature.

Wooden door

For sheathing a wooden door, you will need the following materials and tools:

panels of the selected material;
measuring instruments (tape measure, level);
pencil;
suitable cutting tool;
screwdriver;
planer and sandpaper;
screws or nails;
varnish and brushes.

Standard lining

Preparatory work is similar to that performed when sheathing leatherette. The door leaf will also need to be dismantled, cleaned and removed fittings. Then you need to decide on the direction of the skin - it will be horizontal or vertical.

The lining begins to be mounted from the lower edge of the door, checking the accuracy of its location with a level. It is better to fasten the material with special finishing nails, which will stand out less against the background of the coating, but self-tapping screws can also be used.

Panels can be fixed in different ways

During installation, the panels are fixed closely, inserting each subsequent one into the connector of the previous one, and the sides are closed with special corners. After the completion of the main work, the lining can be varnished. Then, after waiting for it to dry completely, fittings are installed on the door, and the structure itself is returned to its place.

Metal door with clapboard trim

Metal doors sheathed with clapboard, in view of the strength of the metal, will be a little more difficult to make. To fix the panels, you will have to build wooden frame attached to door structure, and already mount the finishing material on it.

To make a frame you need:

bars or slats made of wood;
drill and screwdriver;
self-tapping screws;
saw;
pencil and tape measure.

Frame installation

The slats need to be adjusted to the dimensions of the door (length and width). Then drill holes in them for the diameter of the self-tapping screws, attach the components of the frame to the surface of the door and through these holes put marks on the metal. In the intended places, the metal structure will also need to be drilled.

Further, the frame elements are attached to the door leaf with self-tapping screws. The resulting design can perform another function - to serve as the basis for laying insulation. If you want to reduce heat loss, the selected heat-insulating material is placed between the frame rails.

The next stage of work is finishing. The panels are mounted in the same way as described for a wooden door and using similar materials.

Clapboard panels are a good solution for finishing and simultaneously insulating the door

Decorating a door is a fascinating and creative process, but a responsible one. However, if you have a desire to try yourself in this business - do not hesitate. A serious approach and a little training before finishing work will allow you to turn your ideas into reality, and the result will be a reason for pride.

The entrance door group is now mostly made of metal, so they primarily perform a security function. But budget options have some drawbacks. These include poor heat and noise insulation. The simplest and affordable way to compensate for these shortcomings, upholster metal doors with dermantine. Before ready-made entrance groups appeared on the market, they were often ordered individually and made from sheet steel.

An example of upholstery of metal doors with leatherette

They were distinguished by a sufficient degree of reliability, but did not have a very presentable appearance, and therefore required additional finishing with different materials.
Finishing options were:

The most common is the upholstery of a metal door with dermantine.
Wooden overlays.
We also used MDF panels and laminated canvas.

Finishing the front door with leatherette, as a more expensive option with natural leather, was the most popular.

Existing leatherette colors

This is due not only to the aesthetic appeal that the door acquired after finishing the entrance group, but also to practicality. Increased sound absorption, thermal insulation. The most used material to this day is vinyl leather (leatherette). If earlier its range was not too wide, now you can choose a finish that will satisfy every taste. They will fit into diverse interiors.

An example of leatherette door trim

From the side of the street it is finished, for example, with wooden slips, MDF slips, and the inner side of the canvas is upholstered and insulated with leatherette. This type of design is more suitable for private houses. IN apartment buildings more often they are covered with leatherette on both sides of the canvas. Exterior trim can be made in one color, vinyl leather texture, interior decorated with a different type of material, more suitable for this interior.

The upholstery of metal doors is somewhat different from the upholstery of a wooden box, but in general the same technique is used.

How to sheathe a door with dermantine with your own hands

Do not rush to purchase a kit for sheathing fabrics in a building supermarket. Ready-made kits may have different configurations. It is necessary to decide not only on the type of vinyl leather, but also on the purpose of finishing. Usually, in addition to the decorative effect, the door is additionally insulated and soundproofed.

Options for sheathing metal doors with leatherette

What materials and what are they used for?

Stages of upholstery of steel doors with dermantine with your own hands

First of all, you need to buy material to fit the metal. It is purchased at the rate of 10-15% of the stock.
Then prepare the tool:

Do not forget to purchase a universal adhesive for joining surfaces from various materials.
If you decide to upholster or replace the upholstery of a metal door, then it is better to dismantle it, remove it from the hinges. But you can do it on a hung canvas.

First stage, dismantling

Remove all fittings: handle, lock, peephole. Next, if there is, remove the old upholstery.

In the event that an internal insulation will be installed, it is necessary to separate the sheets.

The second stage, installation of insulation inside the door

For this, extract old stuff, cut the insulation to size and insert a new one. It can be mineral slabs made of fiberglass, basalt. It is important to remember that it is necessary to cut holes in all layers of insulation for the reverse installation of fittings.

The scheme of installation of insulation on the door

The third stage, lining with noise and heat insulation

It is better to start installation from the outside of the canvas. Cut out and glue the vibration filter. Then you need to glue the isolon (noise insulator). To do this, an adhesive composition is applied to the surface of the canvas with a brush on the canvas and the material is attached, especially carefully attached around the perimeter.
On top of it, in the same way, foam rubber is glued. Sometimes batting is used (fluffy material on a stitched mesh base).

After installing the lining material, you can additionally staple all layers using a stapler. It is better to do this around the perimeter of the door leaf, stepping back a few centimeters from the edge, and in the middle of the leaf. Attach with staples only at certain points so that the surface remains flat. Such upholstery with insulating materials will significantly increase the quality characteristics of the doors.

No matter how expensive and high-quality the door is, after some time it will lose its original appearance and require restoration. The easiest way to give a door a second life is to upholster it. A variety of materials can be used for door trim. The technology of work from the upholstery material practically does not change. Read the suggested instructions, and you can easily do the repair yourself.

What you need for door upholstery: preparation for work

Many different materials are suitable for self-upholstery of doors, namely:

PVC film;
leather;
dermantin;
vinyl skin.

The last option on the list is the most preferred. Viniliskin is superior to leatherette and artificial leather in terms of basic quality characteristics and is cheaper than genuine leather.

Upholstery material can be purchased at a specialized store for a cut. In general, the size of the cut should be approximately 15 cm larger than the dimensions of the door on each side.

Upholstery will require you to make special rollers from upholstery material. In total, you need to prepare three strips with a width of about 100-150 mm. Choose the height individually according to the height of your door structure.

Choose your lining material. A budget option- foam. A lining 1-2 cm thick is enough.

If you want to improve the sound and heat insulation characteristics of the door, use isolon instead of foam rubber. This is very practical material with excellent performance properties. It costs a little more than simple foam rubber and significantly surpasses it in all characteristics.

Additionally, you will need to buy various small accessories, the same decorative nails. A huge selection of such products is available for sale in a wide variety of color variations. Choose to your taste.

If you wish, you can buy upholstery nails, originally upholstered in leather or leatherette. They will be invisible on the main door leaf, which in many situations is the right decision.

In general, try to choose nails whose color will be as close as possible to the color of the upholstery. After restoration, the door should have a harmonious appearance, unless otherwise provided by your design project.

Work on self-upholstery of the door is carried out using glue. You can buy the most ordinary Moment type glue, etc. About 100 ml of glue will go to one side of the door leaf.

In the process of self-upholstery of a wooden door, there should not be any difficulties. Understand the proposed instructions, understand the difference between the sheathing of the outer and inner planes of the canvas and get to work.

Finishing the inside of a wooden door

This method is suitable for finishing those models that open inward, i.e. into the space of the room.

First step. Make a special roller. With this element you will hide the gap between door frame and directly to the canvas. Also, in some situations, the roller will contribute to a tighter fit of the canvas to the frame.

Second step. Attach a strip of upholstery to the front of the door so that it rests on the base by about 35-40 mm. Fix with a special stapler.

If overhead locks are installed on the door, start fastening the material from it. If your locks are mortise, fastening should start slightly below the central part of the long side of the door. Cover the entire perimeter of the canvas with similar strips.

Third step. Lay foam rubber or other selected filler. Pre-cut the material into strips about 100 mm wide. To attach the lining, use the same stapler. The resulting roller should protrude by approximately 10-40 mm, depending on the characteristics of the ratio of the door itself and decorative trim. On this roller is ready.

Fourth stage. Measure the space between the inner edges of the roller you created and cut out a strip of thick foam rubber. To determine the appropriate strip width, subtract 10 mm on each side from the previous bead measurement. Attach the finished foam strip.

Fifth stage. Proceed directly to the upholstery of the door. Take a piece of the selected upholstery material around the corner, carefully fold its edges about 6 cm and lay it in the corner of the door leaf so that the upholstery comes a little on the surface of the previously prepared roller.

Hammer a decorative nail at a distance of about 0.5 cm from the edge.

Take the upholstery material by the second upper corner, tuck it in the same way, and drive in the second decorative nail, pulling the upholstery a little.

Make sure the piece of upholstery is laid evenly. To do this, run your hand along the center line of the door with a small clip, reach the bottom and, holding the upholstery tightly with your hand, attach its lower corners to the edges of the door. If the distance is the same on both edges, you can continue to work. If there are discrepancies, the fastening of the upholstery will have to start over, otherwise it will be uneven and ugly at the end.

Nail the upper edge of the canvas with decorative nails in 1 cm increments. Then, follow the same pattern, finish any side part, carefully tucking the upholstery material at an equal distance and slightly pulling it back.

Get to the bottom edge and move on to finishing the second side. At the end, fix the lower free edge with a stapler. On this self-plating completed. Proceed to install the peephole and old or new locks.

If the door structure consists of two wings, the restoration is carried out in the same order. An important nuance is only that the vertical roller needs to be equipped on a sash with a handle.

Video - Do-it-yourself door upholstery

Finishing the outside of a wooden door

This is an instruction for structures tearing outward.

First step. Close the door and transfer the projection of its box directly onto the canvas. This will give you the outline of the new upholstery. Indentation around the edges is necessary for the "quarter".

Second step. Fasten the lining material with about a centimeter indent from the intended line.

Third step. Just as in the previous instructions, nail the main piece of upholstery, leaving its bottom edge not fixed.

Fourth step. Make an insulating roller. With external upholstery, it is attached to the box, and not to the canvas. It is made in almost the same way as when making internal upholstery, only the volume of internal foam rubber needs to be slightly increased.

Place the roller on the hinge side so that it is flush with the door jamb. In relation to the lock side and the upper part, the roller must be extended by 0.5 cm. Attach the underside of the finished roller to the door leaf so that when closing it is tightly pressed against the door sill.

If you attach the roller directly to the threshold, it will wear out very quickly due to rubbing with your feet.

Fifth step. Fix the bottom edge of the upholstery with a construction stapler, and then install the locks, new or old handles, a peephole and, if necessary, decorative elements.

There are two main options for sheathing a metal door structure: a budget one using materials like vinyl leather, leatherette and the like, and a more expensive one using decorative panels. Read the instructions for each of them and choose the option that suits you.

Video - Upholstery and insulation of metal doors

Budget way

Restoration of metal doors can be performed using the same materials as wooden canvases. However, in this case, there is no need to use decorative carnations - everything is done with glue.

First step. Carefully grease the edges of the door leaf with high-quality glue and fix the foam strips on it. Cut off the excess lining along the door profile.

Second step. Apply adhesive to the end of the top of the door and proceed with gluing the selected upholstery material. Glue the top first, then door hinges, after them glue the locks, and finally the bottom of the door. Smooth out creases and get rid of material distortions directly in the process.

Third step. After the glue has completely dried (drying time is indicated in the instructions for a specific tool), cut off excess material, if any, with a sharp clerical knife. Be careful not to damage the main upholstery.

Fourth step. Install the peephole, handles and return the locks to their place.

expensive way

This method involves padding metal structure special panels. For outdoor upholstery, linings made of MDF are optimally suited. They are made in several standard sizes. After such upholstery, the door will look no worse than expensive factory-made counterparts.

Perform interior decoration with wall panels. Choose the upholstery material in accordance with the interior of the room and the features of the operation of the door. MDF has a more attractive appearance, often imitating the texture of exclusive and expensive wood, but this material needs to be treated with care. Plastic panels are much easier to maintain, but not as beautiful.

First step. Measure your metal drill. You need to know the width and exact height of the canvas. On the inside of the door you will find corners designed to increase the rigidity of the door structure. The width of such corners corresponds to the depth of the door leaf. You also need to fix this parameter in the measurements. You will need it when buying sheet foam and wooden beams.

Define the inner height of the canvas as the distance from the bottom to the top corner. Width inner surface, respectively, will be equal to the distance between the side metal corners. Record the measurement results.

Second step. Go to the construction store along with the results of previous measurements. Buy there polystyrene, panels of the selected material, wooden beam And decorative corner with a 10-15% margin.

Third step. Return home, and proceed to finish the door. First, cut the block into 4 pieces. The length of these segments must correspond to the width of the door leaf.

Take a bar, attach it to the upper edge of the canvas and, using a marker or pencil, draw a line along this bar on the base. Do the same at the bottom of the canvas. Place the remaining blocks on the door so that all 4 bars as a result are installed at approximately the same distance. Leave appropriate labels.

Fourth step. Armed with an electric drill, make 16 mounting holes in your door. There should be 4 holes for each bar. The diameter of these holes should be equal to the diameter of the screws.

Fifth step. Fix the bars on the canvas with self-tapping screws. This will give you a frame.

Sixth step. Drill mounting holes to secure the upholstery panel. The optimal number of holes for mounting each such panel, as a rule, is given by the manufacturer in the attached instructions.

Seventh step. Prepare peepholes, locks and handles in the facing panel.

Eighth stage. Fix the panel. For greater convenience, you can remove the door leaf from the hinges.

Move on to upholstery on the inside of the door leaf.

First step. Fasten the frame bars to the canvas as you did with the outer upholstery.

Second step. Cut the foam into pieces, focusing on the distance between the frame bars. In the appropriate parts of the foam, make holes for the peephole, handles and door locks.

Third step. Lay the foam sheets in the spaces between all the bars. Additionally, you can fix the foam with high-quality glue.

Fourth step. Attach the inner panels to the frame. Plastic panels fastened with a stapler, while fixing the MDF panels is carried out with clamps.

Fifth step. Attach the decorative corner suitable material along the perimeter of the door leaf. It will hide the edges of the upholstery elements and give the door a more attractive appearance.

Sixth step. Put a peephole, handles, locks, if necessary, replace the trim.

These simple instructions will allow you to update the look of your door with minimal financial and time costs.

Successful work!