The door handle doesn't stay on. Door handle repair: do-it-yourself step-by-step instructions. Handle Dropout Repair

Breakage of the door handle, including on the entrance structure, is a common problem that can be easily dealt with on your own. There are several ways to fix a broken handle on the front door with your own hands, but first you need to establish the cause of the breakdown.

Such handle options are installed on the input structures, such as stationary (they simply serve as a handle), pressure (they are a lever that opens the lock when pressed) and rotary.

Stationary ones break due to weak fastenings or too much load, as well as due to mechanical damage.

If the handle on the front door, related to the push or turn model, is broken, then the cause of the breakdown is most often a malfunction of the mechanism. Since the causes and remedies for breakdowns are directly related, it is necessary to deal with the types of breakdowns. There are several options here:

1. When pressed (turned), resistance is felt, the handle is hardly set in motion. The cause of the malfunction in this case is most often a lack of lubrication in the lock or looseness of the mounting bolts.
2. After pressing (turning) the handle does not return to its original position. Such a breakdown occurs due to a malfunction of the return spring (it can fly off or burst).
3. The mount remains in the canvas, and the handle breaks off. This is due to deformation or displacement of the retaining ring.
4. The tongue jams, stays in place when pressed (turned). This phenomenon is associated with a malfunction of the tetrahedral pin (square).

The last problem can also be caused by several reasons.

Jammed tongue

If the tongue does not move, then the problem may be in a too short square. Due to the wrong length, the pin moves freely in the mechanism and presses the latch, preventing it from working properly.

Also the square can be broken. This phenomenon is not too frequent, and it is associated with the poor quality of the material from which the door handle is made. In such a situation, most likely it will be necessary to change the mechanism completely.

How to disassemble the handle

Before you start repairing the front door handle, you must remove its mechanism. However, if the handle breaks off, then you don’t have to remove it, it will only be enough to disassemble it.

Push construction

To change push model, no special tools are needed - just one screwdriver is enough. First you need to remove the decorative rosette, which can be screwed on from below with a small screw. The socket is removed through the handle. Then you need to unscrew all the other screws and screw ties on which the mechanism is attached. Now it remains just to remove the handle and remove the mechanism.

If a design is installed, which is one large overlay (such products are often found on Chinese models), then it is removed differently. On the inside of the canvas under the overlay, you need to unscrew the fixing screws (there are 2 of them), after which the handle is completely removed along with the overlay, sometimes from both sides at once.

rotary model

If the rotary model is broken, then in addition to a screwdriver, you will need a thin metal object (awl, knitting needle, etc.) to dismantle such a product. First you need to remove the decorative sockets. A technological hole will open on the side. Insert the sharp end of a thin metal object into it and move the pin away. After that, you can remove the handle and the entire broken mechanism.

How to withdraw

Repair of the door handle of the front door is carried out only after its removal. Depending on their shape (round or standard fixed bracket), such products are removed in different ways. The methods for each product are described in detail below.

Round

Often round models are equipped with a turnkey locking mechanism on one side. Included with such a handle is always a special key with an emphasis for disassembling the mechanism.

You need to remove the round model from the side of the door where there is no hole for the key that closes the lock. Take a flat screwdriver and pry off the decorative trim that covers the fasteners, then remove the trim from the latches. Press a special key on the opened stopper, at the same time pull the handle, and it will be removed. Unscrew the 2 screws on the side of the removed handle with a suitable screwdriver (flat or Phillips depending on the mounting) and remove the remaining halves of the handles on both sides of the door. Then remove the latch by unscrewing the screws securing it.

Stationary

Removing the stationary model is easy. To do this, unscrew the fasteners on which the handle is attached with a screwdriver and remove it from the door. Moreover, the shape of the product does not have here special significance: decorative round and “staple” handles are removed in the same way.

Repair

Repairing a door handle is primarily about eliminating the causes of a breakdown, so you must first determine the problem. The list of major breakdowns boils down to two: the entire mechanism does not function fully or the door does not open, although the handle is working. If the handle is working, how to repair door handle do-it-yourself front door, described in detail below.

If the stationary model is loosened, then the problem is solved simply: you need to tighten the fasteners (bolts or screws) that fix the handle, or simply change it.

If the handle is working, but the door does not open, then this problem can be solved by removing the retaining ring and putting another one. To do this, you need to remove the handle elements from the door according to the instructions above and simply replace this part with another one.

If the handle is hardly pressed or turned, an attempt to open the door is accompanied by a creak of parts, then you need to disassemble the handle and oil its elements.

If the latch breaks, you will have to purchase another square. First you need to completely disassemble the device, remove it from the door and replace the pin (square) with another one that is suitable in length.

When the handle does not fit, the spring needs to be replaced. To do this, you will need to remove the mechanism from the front door, remove the old spring and replace it with another one.

Replacement

If the repair of the mechanism is not possible, then it is necessary to replace the front door handle with another one. To begin with, a latch is inserted into the end hole, which is screwed with self-tapping screws on both sides. After installing the latch, it is required to clean the hole from construction debris. This can be done with a jet of air, such as a hair dryer.

After that, a pin (square) is inserted into the corresponding square hole of the latch. A handle is attached to the pin on both sides. It is important not to confuse which side should be on the left side of the handle, and which side should be on the right. The correct opening of the door will depend on this. Then the handle is screwed to the door with self-tapping screws. Now it remains only to mask the fasteners. This can be done with decorative overlays.

How to open the door if the handle is broken

If the tongue is jammed, you just need to move it away. In this case, it will be possible to open the door quickly enough. To do this, you need to insert some thin, durable object between the door and the latch, such as a screwdriver, and then try to press on the tongue, sliding it inside the lock. This is not always easy to do, so if this is not possible, you can use another method: disassemble the handle on one side. Most often, this is enough to remove the mechanism completely and open the door.

In order to establish the causes of the breakdown of door handles, it is necessary to understand their basic fundamental mechanisms. There are the following types of device:

Also, door handles can be classified according to the material of manufacture:

The main causes of breakdowns

Breakdowns occur even in door handles with the most durable and reliable mechanisms. In order to understand how to fix the handle, you need to find out the reason: why did it break?

Rules for repairing major breakdowns

In general, the repair of door handles comes down to eliminating the causes of their breakdowns. Let's take a look at some of them.

1. If the handle is broken while the mount remains in place, in order to repair the handle, it is necessary to remove the remaining part of the handle from the door and replace the retaining ring with a new one.
2. In the event of a square breakage, it will be difficult to open the door, and, unfortunately, it is impossible to repair such a breakdown. Required here complete replacement devices.
3. To repair a broken latch, you must completely disassemble the device. The short square is replaced by a longer one, which can be purchased at any specialized store. Further, the structure is installed in place, if everything is done correctly, you can open the door without effort. A durable square will serve you for a long time and regularly.
4. If the handle does not fall into place, it is necessary to disassemble the device and correct or replace the spring.
5. If pressing the handle is difficult and a creak occurs, it is necessary to lubricate the metal parts by dropping oil. This failure is associated with clogging of the lock during its operation.

Door handle removal steps

In almost any breakdown, it is necessary to remove the door handle. Moreover, if it is not possible to open the door, dismantling is carried out only on one side.

This algorithm applies to door handles of interior and entrance doors. Sometimes the design may be slightly different. The screw is not located at the bottom of the handle, but on the inside of the door at the top or bottom of the lining. Moreover, the screw may not be one. With this design, by unscrewing both screws, you can remove the handle from both sides at the same time.

If you are repairing the door handle yourself, you need to carefully examine the condition of the mechanism and the handle itself. In some cases, it is required to repair not only one breakdown, but several at once. If the handle is worn out, it should be replaced with a new one. Moreover, the design of the new one should be identical. If it is not possible to open the front door on your own when the handle is pinched, you should contact the experts.

The key on the front door is the lock. If the installation of the entrance metal door is done correctly and during operation it was not subjected to abnormal loads, then the canvas itself will work for many years. But a lock with a handle is designed for a certain number of closing-opening cycles, and over time this bunch of mechanisms fails. Most often, the cause of the malfunction lies in the fact that the handle has broken. If you deal with its device, then repairing the door handles of the entrance doors will seem like a trifle.

Of all types of door handles, push and stationary models are installed on the entrance doors. Swivel mechanisms are installed only on interior doors.

With the help of a push handle, a person controls the opening of the canvas and at the same time acts on the lock tongue, and with the help of a stationary one, only opens and closes.

What usually breaks?

The stationary handle breaks from mechanical damage (from impact) or a loose fastener. If the stationary handle is broken, it can be seen with the naked eye. In this case, it will have to be replaced. If the fasteners are loose, then they need to be tightened.

The push handle, like any mechanism with moving parts, has weak spots, the breakdown of which leads to characteristic problems:

• The handle is connected to the mounting plate by a movable mechanism. Poor quality steel, poor riveting, or excessive mechanical stress cause the handle to fall out of its seat in the mounting plate. In such cases, it will not be possible to repair the mechanism, and you will have to buy a new one.
• A square rod is inserted into the socket on the base of the handle hidden under the mounting plate, which transmits rotation to the lock and shifts the tongue. If, when the lever is pressed, the mechanism works normally, but the lock tongue does not hide, then there are problems with the metal rod. There can be two reasons: during installation, the rod was cut incorrectly and it became short (in a one-sided design). Over time, he could jump out of the hole in the lock case. The second reason is the fragment of the rod due to low-quality steel from which it is made.

Important! It is extremely rare that the seat at the end of the handle can wear out, and the rod can turn.

• Return to its original position after pressing occurs due to the spiral spring, which is fixed at one end on the mounting plate, the other - at the end of the handle. If the spring breaks off or pops out of the mounts, then the spring effect will disappear. Repair of the door handle of the entrance metal or wooden door in this case is possible if the spring remains intact.

As you can see, there is nothing special to break in such a design, and any master himself will be able to establish the cause of the breakdown and determine the way how to fix the mechanism. To do this, it is removed and looked under the mounting plate.

How to remove the push type mechanism from the front door

Consider how the double-sided door handle with a long mounting plate is removed:

• There are two mounting screws at the top and bottom of each mounting plate. Each screw on one side is connected to the screw on the opposite side of the door through a threaded socket (screed). To unscrew the fixing screws, it is necessary to fix the screw on one side of the door with one screwdriver, and turn the screw on the other side with the second screwdriver. door leaf. So unscrew all four screws.
• We remove the handles with fastening straps from the square pin and inspect the turn-and-turn mechanism. We will repair the flown spring, check the mechanism for operability and fix it in place in the reverse order.

In this case, you will have to tinker to get the screws into the coupling.

The order of twisting the mechanism with a decorative strip:

• In this system, the handle is additionally fixed to the square rod with a small screw screwed flush in its lower part at the very decorative strip. Use a thin hex wrench to loosen this screw. It is enough to make a few turns for the screw to come out of the hook with the pin. It is not necessary to unscrew it completely.

Important! This screw is the reason why it is not possible to remove the handle with the decorative strip.

• We twist the decorative overlay counterclockwise with our hands.
• Now the fixing screws will open, with which the bar is attached to the door leaf (or the screws for the screed connecting the two bars on opposite sides of the door leaf). We unscrew these screws and remove the handle from the square rod.

After that, we inspect the rotary mechanism and determine whether it is possible to fix the breakdown or whether the door handle needs to be replaced.

Replacing the handle on the entrance metal and wooden doors is the same. The only difference is that when buying a new mechanism for a metal door leaf, its dimensions must exactly repeat the parameters of the old one. Its mounting holes, the location on the keyhole mounting plate must completely coincide with the holes in the metal sheet.

What can you fix yourself?

On your own, you can perform the following repair of the handle:

• The handle falls out of the socket of the mounting plate if the retaining ring, which sits in the groove on its end, has flown off. The ring flies off for two reasons: it unclenched or burst. To determine whether the ring is whole or not, it is necessary to remove the mounting plate from the door leaf. In this case, the ring (or its fragments) will fall out. If the ring is intact, you can try bending it to increase the clamping force. After that, the handle is inserted into the hole of the mounting plate and the ring is put on. After checking the reliability of fastening, the mechanism is installed in place. If the ring burst, then it is unlikely to be replaced. In this case, the entire front door handle will need to be replaced.
• If, after dismantling the mounting plate, it turned out that the square had burst, you can breathe: this breakdown must be repaired. Buying a new square is not a problem, only this time make sure that it is not silumin, but steel. Before installation, the square is cut with a grinder or a hacksaw to the desired length, the ends are rolled with a file.
• If the latch does not work, find out if the reason lies in the length of the pin, or if the return spring of the tongue inside the lock itself has flown off. To do this, remove the mounting plate and check the operation of the tongue with a screwdriver, turning the square socket in the lock body. If the tongue works, then the pin needs to be lengthened. It is better to buy a new one and cut off a piece of the correct length. It is possible to put linings (cardboard, wood chips) into the socket at the end of the handle, so as not to allow the pin to go deep into it too much and not fall out of the socket in the lock body.

• If the spring has flown off and the mechanism does not return to its original position after pressing the lever, it is also necessary to first remove the mounting plate. The spring is attached under the retaining ring that holds all the mechanisms together. Therefore, you will have to remove the retaining ring and fix the spring. If it burst, then you can search and buy a new one. But usually in this case you will have to go shopping for a new front door handle.

Video on how to remove and repair the push handle:

To remove the handle, check the integrity of its parts and determine the possibility of repair, you will need a screwdriver and no more than five minutes of time.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your own ...

New Articles

New comments

Artem

Grade

Elena

Grade

nezabudka-1

Grade

Catherine

Grade

Vladimir

Grade

Latest reviews

adminadmin

We will send the material to you by e-mail

In the life of any person, a situation can happen when, through the negligence of the user or from old age, the latch fails. Therefore, the question of how to fix the door handle remains very relevant. This is exactly what the HomeMyHome editors will tell you in detail today. In today's post, you'll learn about possible breakdowns and ways to eliminate them.

If the lock inside the door is broken, do not rush to break it out, there are ways to fix the breakdown
PHOTO: ps-resource.ru

It happens that the locks stop working at or at the most unexpected moment. Finding a way to repair it is possible only by determining the type of malfunction.

If the mechanism is stuck

This problem occurs more often not because the core of the lock has failed, but the door itself has been incorrectly configured or not inserted into the box according to the level. To determine what prevents the mechanism from closing properly, you can open door by pressing the handle. If in this position the handle with the bolt works normally, then the cause is a malfunction of the striker plate. The solution to the problem looks like this:

• tighten all the screws on the slats and the lock itself. Be sure to lubricate them with machine oil;
• if necessary, we adjust the door in the doorway.

If it's not the striker plate, then you need to do the following:

• grease the latch with WD-40;
• work with the mechanism;
• if it does not help, disassemble the door handle;
• slightly loosen the locking screw and reinstall the lock.

It happens that the lack of lubricant affects the performance of the door handle. A simple spritz of machine oil or other industrial grease will help correct the seizing.

PHOTO: psk-remont.ru

Handle falling out of the door socket

The retaining ring, which is a mandatory part of the door lock, tends to pop out. You can observe this situation after hitting the door or a strong slamming.

PHOTO: leroymerlin-catalog.biz

Such a ring can be inserted into place if it is intact. In case there are cracks or other defects, it is changed. It can be purchased at a hardware store or simply replaced with a washer. If it does not fit a little, it is bent with pliers so that it presses the core well.

Broken door handle spring

As a rule, so small detail need a replacement. Its breakdown can be caused by careless handling of the door handle. To repair it, you should disassemble the hardware to the core, remove the top washer and look at the condition of the spring.

PHOTO: remont-moroz.ru

It happens that it just jumps off and has no special defects. She is returned to her place. If there is any damage to the structure, it must be replaced. If the spring is difficult to remove from the grooves, then it is intact, and the breakdown is different.

Lever does not return after pressing

If the handle refuses to return, the problem may be due to a dysfunction of the return spring for the door handle. To check this, you need to dismantle the fittings. To do this, remove the core from the socket and remove the spring from the inside.

PHOTO: 1obl.ru

After that, put the new one in place and fix the limiter so that the spring stays inside.

Missing turn of the rod in the door handle

The problem of the lock can be associated with two factors: a licked milled square or a rod simply popped out of the core. To eliminate the cause, it is necessary to disassemble the structure. If a core defect is observed, then it is better to immediately replace it with a new one.

PHOTO: youla.ru

As for the licked square, you can temporarily wrap electrical tape around the axis. This creates a more efficient engagement between the two parts.

What to do if the front door handle is broken: how to fix the problem

In fact, there is nothing difficult in repairing a doorknob. iron door No. If you use the right approach, you can fix the device in 10 minutes. It all depends on what type of handle needs adjustment.

PHOTO: remontidei.ru

We repair the door handle of the entrance metal door

To start dismantling, you need to have a hammer, a Phillips and flat screwdriver, as well as some hex keys on hand. You will also need a drill and sandpaper. The features of this type of repair are as follows:

• you need to act carefully so as not to damage the whole mechanisms;
• all parts must be put in a deep box, preferably with a light bottom;
• in no case do not use a crowbar to remove the lock from the doors;
• it is also undesirable to use a screwdriver, since when unscrewing it, it can lick off the screws.

On a note! If the handle dangles, this is one of the signs of an imminent breakdown. Therefore, it is necessary to tighten all existing bolts. To get to them, you should remove the end ring on the round door handle.

PHOTO: zamokmaster24.ru

How to change the handle on a metal front door step by step

After breaking the handle on the euro doors, you should carefully work with tools. After all, one careless movement can damage not only the core, but it will be impossible to open the door if the handle is broken.

How to remove an old door handle

As they say, breaking is not building, so the process of dismantling the handle can be considered elementary.

1. Remove the protective metal panel on the lock.
2. We unscrew the screws from the washer and remove it.
3. We take out the core and square rod.

Often in designs metal doors there is a factory marriage - the rod is too short. Repair of the handles of the "Chinese" door in such cases is done using a more durable mechanism than before.

PHOTO: ivanovo.itwood.ru

Replacing the front door handle

If the rod becomes the cause of the malfunction, then new handles must also be purchased. It is important to choose them by the selection method, since the sections of the handle hole and the rod itself may not match.

Interior doors and breakage of handles: features of solving problems with a locking mechanism

Intense impact on the mechanism of interior doors often disables the handles. The causes of failures are usually the same as for input structures. Only installation and dismantling can differ, since the device of the door handle interior door with a latch and without it is not the same.

How to remove interior door handle

Replacing the handle of an interior door is carried out in a few elementary steps.

Illustration	Action Description
	We start by looking at the handle. We find on it a small recessed button. To press it, you must use any thin object. In the pressed position, gently try to pull the handle. We pry off the handle cover, if it doesn’t work, unscrew it and remove it from the rod.
	We unscrew the bolts from the interior door that hold the round handle. We use a Phillips screwdriver for this. Only in extreme cases turn to a screwdriver for help. Now we remove the entire core from one side and the other.
	We unscrew the larva, for this we remove the two bolts on the lock itself. We take out the mechanism.

How to disassemble the handle of an interior door, depending on the type of mechanism

Handles for interior doors also differ in a wide range. Often the whole thing is not so much in the form, but in the working mechanism. Therefore, the analysis of the design may have discrepancies.

PHOTO: domaster.ru

We dismantle the stationary and push handle

The stationary handle is installed for many years. It does not have any working mechanism, but only serves to open and close the door leaf. Usually it is connected by a common axis. The door handle can be mounted on screws from different sides. Dismantling such a device is simple.

Important! It is possible to remove screws with a screwdriver only if the threads are coked and cannot be unscrewed with a screwdriver.

The push handle is popular among others. It is shaped like the letter "G". When pressed, the latch tongue enters the lock hole, after which the door opens. Such a mechanism closes without pressure. A similar design is disassembled by unscrewing all the screws and removing the inside. Dismantling is similar to dismantling the front door handle.

PHOTO: zamok-service31.ru

How to disassemble a round interior door handle

Round door handles of the interior door are fixed with special bolts or. It is enough just to unscrew them, and then remove the structure.

1. We open the door and turn the handle so that the internal button on the handle body is visible through a small hole.
2. We press on it with an awl, needle or hairpin.
3. Further, the handle body is removed without difficulty.

In case the handle does not turn, you can drill a hole with your own hands to press the button on the core.

PHOTO: www.aliexpress.com

How to disassemble the handle in an interior door with a lock

In a house where a large family lives, from time to time you have to lock yourself, so knobs are often installed. They are dismantled in almost the same way as a round one without a retainer. To fix the door handle of an interior door, you need to do everything in stages.

1. We remove the protective ring or bar that hides the entire mechanism.
2. Next, you need to deactivate the stopper. It is located inside the protective element. To do this, use a special key or millimeter hexagon.
3. While pressing the stopper, gently pull the handle towards you so that it pops out of the mechanism.
4. If screws are provided in the design, they are unscrewed.
5. On the opposite side, we also remove the structure along with self-tapping screws.
6. After the fixing screws are loosened, the handle, together with the core, can be easily removed.

On a note! Ordinary knobs that have a thru-axle have a threaded mechanism. Therefore, in order to remove them, it is necessary to hold the handle on one side, and on the other to perform turns.

PHOTO: yandex.uz

The specifics of repairing the door handle of an interior door

All door components require replacement over time. The repair operations are exactly the same as for the front doors: lubrication, tightening the bolts, changing the handle itself.

The whole process of troubleshooting is best done in stages. It is important to install all the details in the right place.

Basic interior door handle replacement

After dismantling the old non-working structure, inserting a new handle is simple. To do this, follow the step-by-step photo instructions.

Illustration	Action Description
	We insert the larva of the handle in the same place, if it matches in size. Using a screwdriver, we screw in the screws that will hold the latch.
	We unscrew the bolts that are shown in the photo. They will be needed to fasten the handles together after installation. We disassemble the opposite side of the handle, then remove the protective washer using the key that comes with the kit.
	Insert the disassembled, then insert the bolts. We screw them into the holes of the opposite handle. We combine the holes on the handle and insert the handle until it clicks.

We check the performance of the design. If everything is done correctly, not only the rotary mechanism for opening will work, but also the latch-limiter.

How to fix the interior door lock if a foreign object got inside

It happens that the door lock in the house jams precisely because of the ingress of debris, dust or other small objects. To fix this problem, you will need a carpentry skill and some equipment: a screwdriver, pliers, a screwdriver, grease, old Toothbrush, tweezers.

1. We disassemble the lock body and remove the cylinder from the door leaf.
2. We lay the design on light matter so as not to lose details.
3. We check how the mechanism works outside the door.
4. If something sticks, we lubricate and clean all contact parts.
5. We examine whether a foreign object has fallen into the lock.
6. If there is something, take it out with tweezers.

Further, if the design has worked, we insert it into the door leaf, following the steps in reverse order, starting from the third paragraph. For a more detailed acquaintance with the process, we recommend watching the video.

Lock.It is built into the door leaf, has a tongue and crossbars that are locked with a key. Now we are only interested in the tongue (dog), as the part that is directly affected by the handle;

Lever.By pressing it, the whole mechanism is activated (there are handles with a keyhole, the so-called knobs);

Square pin (square). Connects two handles to each other and transfers the rotary movement from them to the lock;

decorative overlay. Hides the mounting part and screws, performs an aesthetic function. It is square and rounded. The handles on the bar do not have a decorative overlay, since the bar itself is one;

Reply part. Installed on door frame wooden doors, in metal is extremely rare. The reciprocal part includes a tongue.

Problems and breakage of door handles.

The door handle is stuck.When you press the lever or rotate the round handle, you have to make additional efforts, press harder, pull the door towards you or vice versa, press on it with your knee or shoulder.

The door handle is loose or sagging.- By pulling the handle, you can watch how it moves away from the door, the fastening screws become visible. There is a feeling that the lever is about to come off and remain in the hands.

The door handle does not return to its original position.- After pressing the handle, instead of returning back, it remains at the bottom point. Such a picture can be observed, both in old pens and newly installed ones. The reason may lie not only in the handle, perhaps the lock drive is broken.

The lock tongue does not respond to pressing the handle.- The tongue goes inside the castle, or vice versa, went inside and does not go out.

The door does not latch onto the latch.- You have to slam the door hard or press on it, or pull it towards you.