How to straighten a door. The interior door sank - what to do and how to fix it? Door handle height from floor

The question about adjusting doors is relevant at any time and absolutely for all people. No one is immune from minor breakdowns in the house, especially when it comes to such frequently used structures. How to deal with the problem should be considered in relation to specific elements of filling the doorway.

Sometimes interior doors need adjustment.

Possible problems

Adjustment interior doors absolutely always required, regardless of whether problems have already arisen or while the design is functioning without failures. If you maintain the normal condition of the door and its elements, you can significantly extend the life of the door. If the moment has been missed and you have to carry out emergency targeted adjustment of interior doors with your own hands, then it is important to know what problems occur most often and where to look for their cause, ways to eliminate and options for preventing recurring situations in the future.

Door doesn't close well. If there are areas of chafing on the floor, it needs to be repaired. door hinges and adjust the position of the canvas. If there is contact with the box, set the position relative to the frame. When there are problems with fixing the closed position of the structure, you need to pay attention to the lock.
sagging doors. Most often, this leads to sagging of the canvas under its own weight, up to the curvature of the frame.
Creak while driving. Most likely, the grease just dried up in the hinges and needs to be updated. Also, the cause may be a skew in the door frame.
Door won't open. A box may also be involved here, especially if there has been a sudden increase in humidity levels. Another option is to break the lock. Loops in this case rarely break.

Most often, the reason lies precisely in the loops. It is very easy to fix most of these problems with your own hands.

The most common door problem is sagging.

Since a specific situation may be associated with several factors, you should consider all the options separately and figure out how to do the repair of various parts of the door block with your own hands.

door frame

The most difficult situation is the adjustment of the doors associated with the deformation of the box. In this case, the design lends itself to the greatest destruction and sometimes fix the problem with your own hands without complete overhaul box is impossible. If the situation is ignored, the canvas shifts in relation to the diagonal, begins to rub and can even pull the racks off the wall.

How to adjust the interior door if the frame is skewed? First of all, you need to remove the canvas from the hinges. Next, you need to take measurements and identify exactly where the displacement occurred. Be sure to check the diagonal, so finding the problem area where the door structure sagged will be much easier.

To further adjust the door, you need to remove all decorative elements and screw additional bolts into the structure to fix the correct position. After that you need to remove the old mounting foam and, having set the spacers, re-foam the seams.

Adjusting the door frame is considered the most difficult malfunction associated with its deformation.

loops

Most of the problems associated with adjusting the door hinges. There are several situations here:

Hinges too deep. Adjustment of interior doors with such a problem is carried out in two ways. If the difference with the norm is insignificant, you need to loosen the screws that fix the hardware plates. With a recess of more than 0.5 mm, a substrate, for example, made of cardboard, will help to lift the hinges.
The loops protrude above the loot or canvas. In this case, the canvas will not fit snugly against the box. In order to correct the situation, you just need to remove an additional layer of material from problem area. It is convenient to do this with a miniature grinding attachment.
Creak. The problem may be related to the ingress of dirt into the hinge. In this case, it is necessary to clean the parts and lubricate them with oil or silicone. If at the same time the door sagged slightly, you need to adjust the hinges. Sometimes the problem lies in the swivel mechanism itself, in which case it will be necessary to repair the door hinges or complete replacement details.
The door sagged. If the door sagged, the reason may be that the hinges are loose. In order to lift the sagging door, it is necessary to tighten the screws more tightly. If this is not the reason, you can put a rubber gasket under the canopy. In some models, you need to knock out the axle. In plastic blocks, adjustment is made by tightening the loops with a hex wrench.

When the door sags the best option- is to tighten the screws on the hinges

Handles and locks

If the leaf does not lock into the opening when closing, check that the position of the tongue in the lock matches the hole in the striker plate. If not, the plate must be moved to the correct level. The second option is to correct the position of the crossbar.

To troubleshoot lock fittings, you need to identify the exact problem.

How to adjust the door lock if, on the contrary, it sticks? If the reason is not that the door sagged under its own weight, then you need to do the following: first, look at how the latch tongue moves, it may be enough just to lift it with a screwdriver. If the problem persists, disassemble the handle structure and check the condition of the internal mechanism. Its parts may move or break, in which case replacement is required. If the handle turns hard, a simple lubrication of the mechanism may be necessary.

In order for the doors not to break, it is necessary to do a preventive inspection of the structure and correct the breakdowns before they appear directly.

With proper care door structure you shouldn't have these problems. If a breakdown cannot be avoided, now you know how to fix it yourself.

If the doors in your house begin to randomly open accompanied by a creak, or vice versa, it takes a lot of effort to close them, it is time to think about what to do if the door is warped and how to repair it.

Getting rid of the squeak

In order to remove unpleasant squeaks, try treating the door hinges with machine oil. This is done as follows: put a wedge on the bottom of the door, then lift it up a little. Gaps will appear on the hinges into which you need to drip a little oil. You can use a pipette for this. To prevent the trouble from happening again, do not forget to periodically repeat the procedure.

Machine oil can be replaced with a piece of lead from a soft simple pencil, which perfectly performs the function of a lubricating material. Under pressure door leaf the stylus will loosen up, and the door will stop squeaking.

Arbitrary opening (closing)

If you notice that your door began to open or close from the slightest draft, this indicates that the hinges are fixed incorrectly. They must be fixed strictly in a vertical line. And if there is an arbitrary opening of the doors, you need to rearrange the hinge from above closer to the inside of the jamb, and when it is closed, the same must be done with the lower hinge, or something should be placed under it.

Also, skewed hinges can become the cause of warping or jamming of the door. To solve the problem, you will have to remove the old screws from the hinges and put longer ones in their place. If you decide to leave the old screws, you will need additional strengthening of the sockets. This is quite simple to do: you need to fill the loops with pieces of wire wool, or drive in a wooden cork, previously lubricated with glue. Also, the door will stop jamming if the hinges are recessed into the sockets.

To prevent the door leaf from skewing, it is necessary to drown the hinge located opposite the skewing. If the above measures did not bring the desired results, you will need to remove a small layer of wood from above. In the same way it is worth doing with a door swollen with moisture.

In some cases, the problem can be solved by walking along the end of the door with coarse sandpaper. To do this, you do not even have to remove the canvas from the hinges. However, if it is necessary to remove a large layer, the door will still have to be removed.

The door is removed from the hinges in the following order: put some solid object under it, lift it, holding it by the middle. Slightly swing the canvas on the hinges, lift with a lever and remove.

It may well be that the door periodically shrinks and swells depending on the time of year. Then you need to remove the extra layer of wood during swelling, and during drying, nail the gasket, the thickness of which you can adjust. The gasket is made in the following way: take a rectangular piece of sheet copper or brass. Its length should be equal to twice the thickness of the door leaf, and its width should be about 4-5 cm.

This rectangle is fixed with screws or nails on a vertical end in the center of the door, and its other half is bent outward and its end is rolled up. Cardboard or several layers of paper are placed between the plates. With these simple steps, you will ensure the smooth closing of the doors. Based on its condition, you can increase or decrease the lining.

Difficulty closing (opening) doors

However, there are often situations in which, on the contrary, closing and opening doors is somewhat difficult. Initially, you need to find out the location of the tongue. If such a defect is present, then scratches will be present on the striker plate. If there are no scratches, rub the tongue with chalk and see the place that it touches. If the damage occurs under the bar, then the cause is the subsidence of the door and it can be solved by fixing the hinges.

If the hole shifts to the side, it is worth unscrewing the striker plate, and then enlarge the hole with a file. Also, the closing of the door can be prevented by a large gap between the door and the vertical bar. To solve the problem, remove the striker plate, lay the gasket under it. Choose the thickness of the gasket according to the situation.

Rotting door frame

If the door frame rots or loosens, you need to change the damaged element, then securely fix the box to the wall and make sure that there are no gaps between the wall surface and the frame. If there are still gaps, they need to be caulked, and then covered with plaster over a fine-mesh metal mesh.

That's all the main troubles that can lie in wait for you when using interior doors. Now you know how to eliminate them, and, accordingly, you will no longer have any special problems.

It is difficult to imagine any dwelling, no matter how many rooms it has, without interior doors. First of all, this enclosing structure is necessary for bathrooms and toilet rooms. Therefore, it is important that interior doors work properly for a long time. To this end, at the final stage of installing the door, it is adjusted.

In addition, old doors often need to be adjusted. It is with this process that we will try to understand in our article. But let's start with a general description of the structural elements of the interior door.

Often, homeowners who are not deprived by nature of the ability to manual labor, decide on self installation and adjusting the doors of the rooms of your house. In principle, such work can be done by hand. But for beginners, it is important to know what the interior door consists of.

The main structural element of any door is the canvas, it is on it that they first of all pay attention when buying a door. Another name for a canvas is a sash.

Installation of the door and its operation is impossible without a box, which is installed in the doorway, and the canvas itself is already attached to it. The box is an original structural element of each specific door, matching it in terms of color solution . This means that the installation of a new sash in old box is not possible.
Often the box comes with the finished canvas. It consists of three or four elements. If the door is planned without a threshold, then the box has a U-shape, it includes 2 long vertical beams (hinged and feigned) and one short horizontal one (lintel). If necessary, the design of the box includes a threshold, in which case it will look like a closed loop.

The decorative function is performed by the platband. It is he who closes the seam at the place of installation of the door frame in the wall opening.

If the thickness of the wall is greater than the thickness of the door frame, then additional plank. It is also a decorative element, the color of which matches the canvas.

An important detail of the doors is fittings, which includes two hinges on which the canvas is attached to the box, a latch and a set of handles. For doors installed, for example, in a bathroom or toilet, a locking device is also provided, which allows you to close the door from the inside.

These are the main structural elements interior doors.

Adjustment of interior doors as the final stage of installation

So, the process of installing an interior door is coming to an end. The box is installed in the opening, and the sash is suspended from it. At this stage, before foaming the gap between the opening in the wall and the frame bars, it is necessary to adjust the door. First, an initial inspection is carried out for the opening and closing of the door, the uniformity of the distance between the sash and the box. There may be several reasons why the gap size is not the same.

The gap can be so uneven that the door hits the jamb from above or below.

If during the inspection no violations were detected, then they proceed to a more thorough check, during which several major malfunctions can be detected. Consider each of them, the causes and ways to eliminate them separately.

Can't close the door

This is the most common problem. There are several reasons that prevent the normal closing of the interior door.

This mainly happens due to skewed door frame, which is associated with its incorrect installation, during which the bars were insufficiently fastened together or the correct proportions were not observed when connecting the horizontal and vertical bars.

You can identify the presence of a skewed box using a level or plumb line. If the case is really in the box, then it will need to be removed. It is necessary to check whether the cut of the joints of the beams is even, connect them to each other again, strictly observing the angle of 90 degrees. Fix all joints with at least two screws. As a result, you should get an even letter P with firmly connected corners.

They may either not be sufficiently recessed in comparison with the surface of the box or canvas.

In some cases, you can deepen the loop by tightening the screws in it, but this does not always work. If it doesn’t help, then you will have to unscrew the hinges and deepen the attachment point with a chisel or grinding.

Deepening hinge grooves by grinding

The hinges can also be incorrectly installed in the horizontal plane: they are deeply removed from the front of the canvas. Then they will need to be removed and moved closer to the facade of the sash.

Door stuck in opening

This means that the door closes without problems, but it is not easy to open it. This problem has two main causes.

Firstly, the fasteners of the box bars are not tightened enough. Everything is simple here: you need to tighten the screws that secure the feigned beam in the opening.

Secondly, excessively deep grooves can be prepared for the hinges.. To cope with this problem, it is necessary to remove the door, remove the hinges and place cardboard under their doors.

A door that is not tightly closed opens or closes on its own

This happens when the door frame is not installed strictly vertically. If its top is littered to the side where the sash swings open, then the door opens. When the top of the box is reversed, the door closes. You can fix this by leveling the box, especially the hinged timber. You can use a plumb line as a guide, but a long level is preferable. It is also possible to use a short level, for this it is worth binding it, for example, to a rule. After leveling the box, secure it to the opening.

In addition to problems with the frame, hinges or door leaf, inaccuracies in the installation of locking mechanisms can be identified.

Adjustment of locks and door handles

A common problem that occurs when installing a door lock is not deep enough. As a result, the side plate of the lock or the door handle touches the door jamb. The way out of this situation is to deepen the hole for the latch or lock mechanism.

Sometimes the lock screws or latches are not screwed in enough, so the mechanism hangs in the groove. The solution is simple - tighten the fasteners.

Adjustment of old doors

Even though adjustment is the final step in installing a door, it often needs to be done on older doors as well.

One of the main and common problems of non-new interior door structures is the squeak of the hinges. Sometimes this is observed with new doors. To eliminate this problem, it is necessary to lubricate the hinges with machine oil. In order to put a wedge under the door, the door is lifted to partially remove it from the hinges. Oil is dripped into the gap that appears in the loop with a pipette, which can be replaced with a piece of graphite lead of a simple pencil.

Another common problem with old doors is skew. He has several reasons.

For wooden doors, skew may be due to swelling of the leaf. In this case, it is necessary to determine the place of protrusion. To do this, paper is applied to the alleged distorted area and the door is closed. The place where the trace of the carbon paper will remain is the segment of the bulging of the canvas. It is it that needs to be cut off, and the door itself must be painted over, as was described in the case of new door with broken geometry.

For heavy doors, for example, made of solid wood, skew may be due to deformation of the hinges. This is usually caused by the loops being chosen incorrectly.

Note! Heavy wooden doors should be installed not on two, but on three hinges.

There are several ways to fix skewed loops:

replace with new stronger ones;
install additional loops;
unscrew the screws from the hinges and replace them with longer ones;
strengthen the sockets for the screws with a cork smeared with glue;
install washers in the hinges, due to which the door will rise a couple of millimeters in the center of the hinge.

Washer installation

The skew of the door leaf can also be caused by a change in the geometry of the opening in the wall. Without replacing the door elements, this defect can be eliminated as follows:

sharpen the door in the place of skew;
remove and rearrange door frame, adjusting the joints of the bars in compliance with the angle of 90 degrees.

In the latter case, you need to focus on the building level, and firmly fix the box to the doorway. To do this, two holes are made through the box in the wall on the side of each beam. The depth of the holes in the wall must be at least 50 mm. Pins made of metal or wood are driven into the holes. Wooden fasteners are pre-lubricated with glue.

Final word

The installation of the door and its adjustment can be done independently, but at the same time it is necessary to observe maximum accuracy so as not to spoil the canvas or the box as a result.

Note! If a wooden door is planned or already installed in your house, then remember that its prevention must be carried out annually.

If you have doubts about your own abilities, then it is better not to take risks and entrust the entire process of installation and adjustment of the door installation to professionals.

Video - Door Adjustment

A skewed entrance or interior door does not fulfill its functional properties, poorly closing, not isolating individual rooms or the general space of the apartment. Knowing what to do if the door is skewed, you can independently eliminate the design or operational problems that have appeared in a short period of time, give the door leaf a second life, saving your finances and time. Most of the defects are successfully corrected at home, without the use of expensive equipment and tools and without the involvement of expensive services of professional craftsmen.

Skewed doors is a consequence of a number of operational or technical properties of the product. Therefore, it is necessary to immediately determine the cause of the appearance of such a deficiency and, first of all, try to eliminate it. There is a difference in the features of the operation of doors made of wood, metal and combined materials.

Over time, even the most high-tech and reliable door samples need inspection and preventive maintenance: lubrication and adjustment of hinges, surface cleaning, coating of functional elements with special compounds.

Note! The cause of malfunctions or damage to the door structure is not always improper operation or mechanical failure. Often the problem lies in the quality characteristics of the product, violation of its manufacturing technology, installation or storage conditions. Therefore, door sets should be purchased only from reliable and trusted manufacturers that guarantee a certain service life and provide certificates of compliance with Russian standards.

Removing the warp of a wooden door

The main reasons for warping doors made of natural wood are high humidity, constant dampness and significant temperature fluctuations. This is usually the most common problem for owners of summer cottages, rural houses or country cottages for seasonal use. Due to the lack of heating in the winter season, the internal elements of buildings become damp and freeze, and when heat sets in, condensation appears in them. Summer heat leads to evaporation of moisture from the wood and its warping. For wooden structures, such conditions become a real test of strength.

Note! Even in apartments and houses with a permanent mode of residence, wooden doors require special protection against distortion, the use of penetrating impregnations and effective coatings.

already skewed wooden door can only be corrected by first removing it from the hinges. You should prepare a planer in advance and remove extra millimeters of wood from the ends of the canvas, including paint or varnish. If the door is severely warped, you can repair it with felt or rubber gaskets. The width and dimensions of the gasket are selected individually, taking into account the actual state of the structure and pre-made measurements. Fix the tapes of the cushioning material with small nails, special glue, furniture or construction stapler. The fastening technology depends on the characteristics of the door leaf and the level of its operational load.

Removing the warp of a metal door

Any designs of metal doors are more resistant to negative climatic phenomena and difficult operating conditions. But there are situations when even the most reliable metal constructions. The most common reason for changing the properties of the web can be the use of too heavy multi-layer steel in the production or a technological violation of the thickness of the product. First of all, they can't stand it. door hinges. They change their technical properties, sag or break. It is practically impossible to eliminate such a disadvantage as an incorrect and incorrectly calculated door design on your own.

Over time, hinges can simply loosen and wear out. It is enough to change them and the door will serve its owners for many years to come. The main thing is to pick up in a hardware store right size loops and make sure of their quality.

The most difficult and serious situation is the skew of the door as a result of significant shrinkage of the house, its individual structures. As a rule, such a problem is associated with non-compliance with construction technology or premature commissioning of the house. In such a situation, change metal door on wooden canvas, which is easier to adjust and fix when changing openings.

Annoying door sagging problem

The annoying problem of sagging doors, especially wooden ones, can happen for a number of reasons.

The root causes may be different, but each of them leads to the fact that the door may not close at all over time, scratch the floor and completely cease to serve. It is permissible to correct the situation with your own hands.
The interior door sagged, what to do? Video

Replacing or adjusting doors if interior doors have sagged

Replacement and adjustment of doors
Repair of doors is required over time for any overlap of the opening of neighboring premises.
The door structure is not only a decorative element of the interior design of the home, but also the main functional detail, without which you simply cannot do without a comfortable stay at home. After all, the door is so necessary in buildings of any type of purpose of use:
Protects the room from drafts;
Separates adjacent rooms relatively functional purpose;
Creates a cozy atmosphere, and play a decorative role in the stylistic design.

Not only a used door can fail, but also a completely new product due to correct installation, shrinkage of the structure as a whole, and so on.
In many cases, households begin to think about replacing the door as soon as possible, which has ceased to be visually attractive and has lost a number of functionality. If the question arises as to whether it is necessary to replace the block with something new, or start repairing doors, then know that even an inanimate interior detail requires attention and care.
The product may cease to please for a number of reasons that can be corrected with your own hands:
The door leaf made of natural solid wood is cracked.

Such a visual misunderstanding is corrected by restoration work or decoration, the list of which is simply unthinkable for choice. The whole process, both restoration and decorative trim canvases of the door structure, reproduced by one's own hands in everyday life with little financial cost.
If the restoration implies a thorough list of works, then it is permissible to reproduce the sash decoration with your own hands without even removing it from the hinges: decoupage, painting, and so on.
The structure of the roof was shattered.

You can also strengthen the door frame with your own hands at home. Why just disassemble the block with a simple tool that everyone has home master or borrow for a short period of time from a neighbor. In this case, it may only be necessary to strengthen the door frame at the installation site, tighten the hinges, or pull the canvas itself, that is, strengthen the loose or cracked panels wooden structure.
Nasty, cutting hearing and nerves, creaking.

Lubricate the door

The creak of an opening or closing sash is often caused by the friction process of the pins, which are elements of the door hinges. The reason for the squeak may also relate to poor fastening of the loops themselves to the loop bar or the end of the canvas.
To eliminate a sharp sound, it is recommended to look at the fastening of the hinges and lubricate them with machine oil, or use graphite, pieces of which are inserted into the hinge gaps.
Doors don't close well.

The door made of wood does not open or does not close, then its problem is hidden in the conditions of internal operation. Over time, any product made from natural solid wood can swell, that is, significantly increase in size around the perimeter. The door does not close yet due to a violation of its geometry: the door swelled, it led, the door sagged, the hinges loosened, the box led, and so on.
There can be a lot of reasons that the sash does not coincide in geometry with the box. If the door has sagged thoroughly, then it is recommended to take the issue seriously, which we will talk about below.
Possible reasons malfunctions

If the design sank slightly or fairly, then this is indicated by the following visual circumstances of the functional activity of the unit:

The first slight abrasions of the door sill, due to the fact that the doors do not close well;
Damage to the flooring when the door does not close at all, that is, it does not fit snugly around the perimeter of the box;
There were clear gaps around the perimeter.

When confirming at least one of the above violations in the quality service of the floor block, there is only one conclusion - the door has sat down with a violation of the fit geometry. Before any adjustment of the doors is made, it is worth examining the unit for a malfunction, and only then get to work.
The main reasons why an interior door made of natural solid wood or other material for internal use does not open include such misunderstandings:

Hinges moved away from the installation site;
Deformation of the door frame;
Violation of the geometry of the sash itself;
Swelling canvas made of natural solid wood.

It is permissible to correct many shortcomings with your own hands, and for work it will be required in all of the following cases:

PVA glue or other adhesive for working with wood;
Screwdriver or screwdriver;
self-tapping screws;
Planer, chisel;
Hammer.

You may also need another simple home tool, which, if you do not have it in the pantry, it is permissible to ask for a loan from a neighbor.
Inspection and repair of hinges

First of all, if the door has sagged, it is recommended to inspect the hinged canopies, since the reason is most often hidden in them. To adjust and return the functionality of the sash, door repair is not required, you just need to remove the canvas from the hinges, inspect them and correct them. The answer to the question of how to remove the door from the hinges is simple:

Open the sash;
Substitute a crowbar or other convenient object under it;
Using a crowbar (or with your hands), lift the canvas from the bottom up.

Thus, the sash will be freed from the hinges, but now it must be safely held so as not to be damaged. For these purposes, if such works are reproduced for the first time, invite a household member to help, who will at least support the canvas so that it does not collapse.
Usually, the hinges are fastened to the hinge beam (door frame rack) using wood screws. If the door sags strongly, then:
Under the unscrewed self-tapping screws, it is recommended to drive wood wedges into the holes, then mount the hinges on the self-tapping screws in place.

Pre-dip the wedges in PVA glue (or carpentry). To fix the hinges, use longer fasteners, and hang the door itself 24 hours after the adhesive has dried.
If the situation has not been corrected with the sagging of the ceiling after strengthening the hinges with wedges and new self-tapping screws, then it is recommended to change the previous place of installation of the hinges.

In this case, you can use the old hinges, but place them on the hinge bar in other places, as well as on the end of the sash itself.
Inserting hinges in new mounting locations is carried out in the same way. The main thing is to correctly calculate the vertical axis of the location of the hinged canopies, and the distance between each other. Grooves in wood are made with a chisel and hammer impact. A chisel is best used with a straight blade.
If the door sagged in a short period after installation, then the problem lies in the large weight of the sash itself, which the hinges cannot withstand.

You can correct the situation just by adding additional loops. You can insert a third loop, placing it at a distance of about 10-20 cm under the upper canopy. Or install an additional loop, shifting the top one a little higher.
If the door has sat down after a long service life, then this may indicate wear on the hinges.

With a long period of service, the core wears out in the loops, which can be simply replaced. But this may not increase the functionality of old hinges, as they also wear out over time. Better to buy new hinges.
With a slight sagging of the door leaf, the hinges can not be replaced, but slightly corrected.

In this case, the doors are adjusted using a steel ring, which must be laid under the metal core of the element. bearing ball right size about the diameter can also help.
If this is not enough to correct the situation, then a backing can be made under the hinges, which will lift them a little from the hinge beam.
Do not forget that after manipulations with hinged canopies, it is recommended to lubricate them with engine oil for prevention.

We reveal the deformation of the door frame

After you have managed to adjust the hinged door, it may happen that it does not open or does not close well. So the hinges here were not entirely to blame.
The problem, most likely, is the lack of the necessary functional gap between the structure box and the sash.
To identify such a problem, you need a building level, which checks the vertical and horizontal of the structure. The door in the course of closing can cling to the box in any part. If a clear violation in the installation or a slight deformation of the box is determined, which is possible after a long period of operation of the unit, then the problem is solved by lightly trimming the fabric of the structure exactly at the site of the problem.
It is worth noting that before taking on the hewing of the door leaf, you need to thoroughly make sure that it was the box that did not succumb to severe deformation. Otherwise, efforts will be reproduced in vain, and the canvas will be damaged.
The fundamental deformation of the box is the most difficult problem associated with the door structure of the ceiling. Adjusting the doors in this case will not help if you do not completely redo the box. After all, how to adjust the door if the base of the floor succumbed to movement. If we ignore the deformation of the box, then in addition to the displacement of the canvas diagonally, over time, the racks will come out of the plane of the opening.

The skew of the frame is corrected by the following manipulations:

The ceiling canvas itself is removed from the hinged canopies;
Measurements are taken of the vertical and horizontal mounting of racks;
The diagonal of the opening is checked;
The place of displacement is found;
All decorative elements are removed from the ceiling: extensions, platbands;
Fixing bolts are screwed into the frame structure, which will correct the situation;
Removed from gaps Construction Materials: plaster, polyurethane foam;
In the necessary places, spacers for the frame are installed, which in the future will hold it in the correct position;
Finally, the gaps are re-foamed and plastered;
Platbands and dobors are installed in place.

Violation of the geometry of the door leaf

Natural solid wood is a very valuable product, especially at home.
Materials of natural origin have always been valued. If a table from an array or other object decorative design the dwelling does not require a certain degree of attention and constant care, then if the door is made of wood, it may be you who are to blame.
Doors made of wood do not close well due to their swelling or, conversely, drying out. This may happen because:

That the norm of humidity in the room is not maintained;
The block may not be treated with protective agents or special impregnations;
The installation itself could take place, for example, in winter time the year when the unit did not have time to acclimatize in the internal heated room;
The installation of a solid wood structure is not recommended in the openings of rooms with a constant temperature difference and humidity fluctuations: bathrooms, showers, and so on.

If the door has already sagged, then you should not immediately run to the construction center for a new replacement from the combined material. Solid wood door repair natural wood made by hand very simply using a conventional planer or more modern instrument.
You can adjust the sash to the parameters of the box by trimming problem areas on the canvas. Before starting work, you need to do at least visual measurements:

Close the door;
Assess the dimension of existing gaps;
Remove the door from the canopies;
Plane the strapping in certain places.

Any design flaws in the overlapping of the openings of neighboring rooms can be corrected with your own hands. If the methods of adjustment do not lend themselves, then it is better to invite a specialist to the house. After all, it is cheaper to eradicate malfunctions immediately, since over time they turn into major breakdowns.

1 /5 (2 )