How to finish the walls of aerated concrete inside the kitchen. How to make interior decoration with drywall at home from aerated concrete? Insulation of aerated concrete walls

Interior decoration aerated concrete houses serve not only for decoration, but also perform a number of functions for warming and protecting walls. Since aerated concrete is a porous material, its condition is strongly affected by temperature and air humidity, therefore, the external and internal finishing of aerated concrete walls acts as a natural protective barrier. This means that it is important for the owners to know what materials to choose for lining and how to apply their properties in practice.

The "bare" walls of aerated concrete are not presentable enough to leave them unfinished. Source tolkobeton.ru

Features of interior decoration of walls made of aerated concrete blocks

Aerated concrete due to the porous structure has a high air permeability. If the wall does not have an interior finish, warm water easily seeps through it. room air. In the cavity of the wall, it is cooled to the temperature of the outside air, forming condensate, which accumulates in the pores of the material. Thus, walls made of aerated concrete without finishing create large heat losses and become damp due to the formation of condensate.

The main task of the interior decoration of a house made of gas silicate blocks is to reduce the permeability of the walls, that is, to "seal" the material from the side of the room. For this, special plaster, plasterboard or wooden sheets are used. Decorative wall decoration on such a basis can be of any kind.

Gas blocks are quite democratic in terms of material compatibility - they can be paired with both plaster and wood Source asm.ru

Types of materials and methods of interior decoration

In modern construction, there is a large selection of finishing materials for aerated concrete. Thanks to this, it is not difficult to choose a lining to your taste and wallet.

For rough finishing of aerated concrete use:

plaster;

plasterboard sheets with insulation.

For decorative finishes aerated concrete can be used:

paint and varnish compositions;

textured plaster;

wooden or plastic lining.

For right choice it is necessary to imagine the properties and advantages of each of these materials.

When installing a rough finish, if necessary, the walls can be additionally insulated Source board.bau.com.ua

Wall plaster

With the help of plaster, you can level the surface of the walls for painting or wallpapering. However, an ordinary cement-sand mortar is not suitable for finishing walls made of aerated concrete indoors. In construction, special plaster mixtures are used, which have the following parameters:

They retain moisture, therefore, when applied, it does not penetrate into aerated concrete;

Improve the adhesion of plaster with aerated concrete;

Make the solution more plastic and comfortable to apply;

Accelerate the process of solidification of the mixture on the wall;

Increase the strength of the coating;

Eliminate cracks during application.

It is better to entrust the work of applying plaster on aerated concrete walls to professional craftsmen. The surface is quite difficult to level due to the texture of the blocks and the unevenness of the seams. It's also important to note that the plaster takes some time to dry, so it can take days or weeks to finish the entire house.

Plaster is one of optimal materials for rough finish Source ukrsmeta.ua

Drywall

An alternative to plaster is the installation of drywall sheets. The method of laying the material depends on the evenness of the wall. If the blocks are laid evenly, the drywall is simply glued to the wall. This method If the wall requires alignment, you will have to install sheets on metal carcass with a layer of insulation.

Drywall is the ideal base for any decorative finish. It can be covered with decorative plaster, painted and wallpapered. Sheets of drywall can be lined with all rooms in the house.

Source feea.org

On our website you can get acquainted with the most popular projects of aerated concrete houses from construction companies presented at the exhibition of houses "Low-Rise Country".

Wood

Wood is an environmentally friendly material and has a beneficial effect on the microclimate of the house. This decoration of the house looks very comfortable. If done wooden cladding throughout the house, it will completely look like a real log house.

Wooden cladding goes well with aerated concrete walls due to the technical similarities of the materials. Both wood and gas silicate have a porous structure and good thermal conductivity. However, the lining is subject to mandatory treatment with water-repellent and anti-fungal varnishes.

The most popular types of wood for home decoration are pine and spruce. They are characterized by high strength, aesthetic appearance and pleasant coniferous aroma.

Wall cladding with clapboard will make the room indistinguishable from the room in log house Source legko.com

Laying ceramic tiles on aerated concrete is recommended in rooms with high humidity - a bathroom or kitchen. The tile will create a protective barrier that will not allow the walls to become damp from steam and condensate.

For laying tiles, you need to use a special adhesive that will create good adhesion to the aerated concrete wall. Ordinary cement mortar for these purposes is not suitable, you need a sealed composition with antifungal additives.

When facing walls made of aerated concrete with tiles, you must additionally take care of a powerful ventilation system so that moisture does not linger in the room. This is the only way to avoid the appearance of fungus and mold in the bathroom.

Ceramic tiles - excellent protection against moisture Source zavoddelta.ru

Wall papering

After puttying or plasterboard sheathing, the walls can be covered with any wallpaper. In this case, it is worth considering their breathability. Eg, vinyl wallpapers create additional protection of aerated concrete from moisture and temperature changes. The paper canvas is more "breathable", it is recommended to combine it with a dense layer of plaster.

The technology for gluing wallpaper on an aerated concrete wall differs little from the standard one. Before starting work, the wall must be primed. Otherwise, the recommendations related to the type of wallpaper and the basis for gluing are observed.

When choosing wallpaper, the main thing is to choose not only the material, but also the pattern. Source qes.ru.net

On our site you can find contacts of construction companies that offer the service of reconstruction and restructuring of houses. You can directly communicate with representatives by visiting the exhibition of houses "Low-Rise Country".

wall painting

Painting walls in a house made of aerated concrete is done on top of plaster or plasterboard sheathing. For finishing, water-based paint of one of four types is most often used:

acrylic;

silicone;

silicate;

mineral.

In order to further protect the aerated concrete from water, acrylic paint is used, which has water-repellent properties. Silicone and silicate paint are vapor permeable, so they require reliable plastering.

Before painting, a rough wall finish is required - a primer, plaster or drywall Source reference.com

PVC panels

Installing plastic panels on an aerated concrete wall is a budgetary and easy-to-perform finishing option. PVC panels can be different colors, as well as imitate the texture of wood or stone. The main condition for their installation on aerated concrete is the presence of a waterproofing layer. This is especially important when decorating a bathroom or kitchen. Also, PVC panels suffer from temperature changes, so they should not be used in the decoration of balconies and hallways.

PVC panels are quite nice and budget solution Source 1zoom.ru

Finishing mixtures must be selected based on their compatibility with aerated concrete. Any company has building materials with such a mark.

Instead of the usual leveling plaster, you can use a decorative textured mixture. It will not work to stick wallpaper on it, but the paint will look very impressive.

In order for the cladding to serve for a long time and perform the functions assigned to it, a forced ventilation system must be organized in the house. This is especially true for bathrooms and kitchens.

Examples of interior decoration of a house made of gas blocks

In this small gallery you can see examples of finishing houses from gas silicate blocks.

Source fr.access.ly

Source techwood-house.com

A very practical application of the space under the stairs. Source yandex.ru

In the attic it is desirable to install large windows Source pinterest.com

Video description

And a slightly non-standard look at the finishing of aerated concrete in the following video:

Conclusion

Since indoor aerated concrete wall decoration plays an important role in maintaining a home microclimate, you need to know and understand the difference between popular room cladding options. Only after selecting the material that is necessary for the characteristics, you can proceed to the choice of the most beautiful and suitable look finishes.

Aerated concrete - popular now construction material, which is used in the construction of multi-storey buildings for various purposes and small cottages. By themselves, autoclaved blocks can stand for a long time without external cladding - the concrete will not be destroyed. However, the interior decoration of the aerated concrete house is carried out almost immediately after the main construction, since appearance products are not the most attractive.

Basic finishing rules

Gas blocks are different from monolithic concrete vapor permeability, that is, the ability to carry out moisture exchange, "breathe". With the right finish, the walls do not get wet when the humidity changes, microflora does not settle on them, and a comfortable climate is maintained in the room. In order not to lose this property when finishing a wall of aerated concrete, several rules should be followed:

• it is recommended to choose "breathable" materials that do not block the movement of moisture;
• the exterior finish must also be chosen wisely - it should not impede the passage of steam to avoid the accumulation of water in the body of the block;
• if the choice is made in favor of dense finishing materials, it is necessary to provide a ventilation layer to remove moisture, or a well-designed general ventilation system.

Warming from the inside

Sometimes the interior decoration of aerated concrete is combined with insulation. Is not The best way make the room warm, because the dew point and the amount of freezing of the wall are shifted inward, which means that the measure is not entirely appropriate, especially when building a private house. In addition, the usable area of ​​​​the rooms is significantly hidden.

Nevertheless, it is possible to finish external walls and partitions with an insulating layer - this compensates for the insufficient level of heat retention in the room, and also improves sound insulation between rooms.

For thermal insulation of walls made of aerated concrete blocks, only breathable materials can be used:

• mineral wool;
• ecowool.

Expanded polystyrene and polystyrene boards will not fit due to absolute vapor tightness, which will disrupt the air exchange of the structure.

What manufacturers offer

For interior decoration of country or apartment building(if you bought an apartment without cladding from the developer) you can choose several solutions:

• wood paneling;
• tiling;
• use of systems from hl;
• artificial stones;
• traditional plastering.

Interior finishing options

Each finishing method internal walls has its advantages and disadvantages. Consider them and the main installation technologies.

Wood

Interior decoration of aerated concrete walls is best done with natural material - wood. It passes air better than others, participates in the regulation of humidity and microclimate in the room.

Sheathing materials include:

• lining;
• board;
• wood panels (plywood, smallpox);
• block house.

Installation of wood paneling is simple:

1. Guide bars are attached to the wall of blocks (rails of any thickness from 2 cm). Their fixation was carried out on special dowels. However, under significant loads, the fasteners can be torn out. To prevent this, it is necessary to fix the dowels to the reinforcement strapping provided in the concrete masonry. The direction of the crate is determined by the desired sheathing method. The step between the slats is determined by the size of the boards or lining. It is optimal to install the lower and upper rows at a distance of 10-20 cm from the floor and ceiling, as well as between them in the middle.
2. Sheathing is attached to the crate - boards, plywood, lining.

This finish does not require waterproofing. At right decision external thermal insulation internal is also not required.

To give the desired shade, the wood is painted with any paints and varnishes, preference should be given to compositions that do not form an impermeable film to preserve the “breathing” of the coating.

To the virtues wood paneling relate:

• low cost of materials;
• very easy installation;
• exceptional environmental friendliness of the material;
• there is no need for additional finishing (wallpapering, plastering, etc.).

Plasterboard technology

Plasterboard sheathing is the second most practical way of environmentally friendly and uncomplicated finishing of internal walls from gas blocks. Gypsum is a natural mineral that absorbs moisture well and gives it back, thus regulating the optimal indoor climate.

Drywall for finishing country house- a real find. He acts as and finishing material, and a building component for creating partitions and interior walls.

The technology for creating structures and cladding is fundamentally simple, but requires compliance with completeness, compliance with many subtleties. However, for simple sheathing, it is enough to adhere to the general principle:

1. Vertical guides are fixed to the wall at a distance of 600 mm. The calculation is simple: a drywall sheet 1.2 meters wide. It must be attached at the edges and exactly in the middle. Guides can be special metal and even simple wooden ones.
2. On the attached crate, the sheathing is fixed with special self-tapping screws for HL, you can use fasteners for wood. Products for metal will not work - they have a very fine thread.
3. Next you need gypsum plaster(putty). She closes the joints between the sheets using perforated tape.

According to this algorithm, partitions are also equipped. Mineral wool insulation can be placed inside the frame - it will act as sound insulation.

Advantages of plasterboard interior decoration of aerated concrete houses:

• absolute environmental friendliness;
• fast work speed;
• no additional leveling of the sheet surface is required;
• the finished surface is suitable for tiling, wallpapering, decorative plastering.

The disadvantages include low load bearing capacity- in order to hang a TV or a kitchen cabinet on such a wall, it is necessary to drill into the guides, and even better - make a special anchor fastener.

Plastering

This is the traditional way of leveling and preparing walls for fine finish. However, the classic concrete mortar not suitable for these purposes: firstly, it has a large weight, and secondly, low vapor permeability. Gypsum plaster mixtures have been developed for interior decoration. They are based on a natural mineral, which, like gypsum sheets, perfectly regulates the level of humidity, passes steam.

Plastering is carried out in 1 or 2 stages:

1. For basic leveling, a plaster mixture is used. As a rule, aerated concrete walls are uneven, the solution is applied and, if possible, immediately leveled. The work will go quickly if you use machine application and a building rule to level the surface. Then immediately smooth the surface with spatulas.
2. If the first stage is done with high quality, then after the surface has dried, it is sanded to remove minor irregularities. If the hand is not stuffed and the wall requires additional adjustment, plaster defects are eliminated by puttying.

After hardening of all layers, produce finishing tiles, wallpapering or decorative plastering.

tiling

Facing ceramic tiles allowed for wet rooms where there is high humidity - bathrooms, showers, saunas, kitchens. The only caveat is that in rooms finished in this way, it is necessary to equip high-quality forced ventilation, because the surface of the tiles does not let moisture in at all.

Installation of ceramic and tiled cladding on walls can be carried out both on gypsum plaster (see the plastering method), and directly on aerated concrete blocks. For these purposes, a special glue is used.

How to tile walls:

1. Aerated concrete must be treated with a deep penetration primer, it is optimal to use a waterproofing solution. Application in 2-3 layers.
2. On a dried base, tile adhesive is applied in stacked fragments, for example, EK3000, Plitonit, Osnovit T-11 or T-12 or any other.
3. The tile is mounted according to all the rules: it is pressed against the mortar, leveled by a level, delimited by crosses for seams.

For damp rooms, a hydrophobic grout is needed to complete the appearance of the surface.

Fake diamond

This method of wall cladding is similar to ceramic coating. The algorithm of the work remains the same, however, the method can be used in any premises.

Artificial stone is made mainly of cement, so its vapor permeability is very low, the installation of the stone is carried out directly on the wall and high-quality ventilation is performed.

Artificial stone used for lining wet rooms must be coated with water repellents to prevent surface damage and fading.

Summary

Most suitable for aerated concrete surfaces modern materials for facing. The most important thing in the selection process is not to overlap useful qualities concrete blocks and use breathable components. If this is not possible for some reason, good ventilation will be the best compromise.

You will have to plaster with cement or gypsum with a thickness of 10-50 mm (depending on the size of the masonry flaws) and only then putty. With a layer thickness of more than 20 mm, it is required to reinforce the plaster with a polymer mesh, which is fixed with galvanized self-tapping screws or nails with large washers; at the same time, the vertical and horizontal fastening spacing should not exceed 50 cm. Preliminary priming will greatly increase the adhesive strength of cellular concrete with a layer of plaster and reduce the risk of cracking.

2 Drywall

Sheathing saves time and allows you to perfectly level the surface of the walls. In addition, it is easy to lay cables and other communications in the space under the skin - there is no need to make fines. But it is important not to make mistakes.

Popular mistakes in plasterboard wall cladding

• Tightening the surface of the blocks with a vapor barrier material is unlikely to significantly extend the life of the building, but in the house it will worsen, decrease and Fire safety. AND
• Use sheets of 9.5 mm (thin plasterboards are not strong enough - they are designed for ceilings and radius structures), it is important to choose a thickness of 12 mm.
• Make a crate from wooden slats, it is less reliable, especially if low-grade material is used (under-dried, with knots and sawing defects). The frame must be made of galvanized metal profiles.
• Do not observe the pitch of the uprights (600 mm) and fastening screws (250 mm).
• Sheathe walls without a frame. This cannot be done with high quality even with very even masonry, since the slightest protrusion or adhering mortar crumb (which, when puttying, is easy to notice and clean off with a spatula) will lead to the formation of a bump on the plasterboard sheathing.

IN country house humidity drops are always greater than in an apartment, and drywall, even moisture resistant, reacts to them: sheets increase and decrease in size. To reduce the likelihood of cracks at the joints, the latter must be reinforced with elastic paper tape (not sickle) and puttied with weber.vetonit JS.

Plastered or sheathed with drywall, apply decorative plaster on them or paste over with wallpaper. In a house where interruptions in heating are possible (dacha, occasionally visited cottage), it is better to choose the first or second option.

3 Lining and panels

The main thing here is to collect an even wooden frame and choose the right fixture. The step of the bars (rails) of the frame for cladding with wood panels should be no more than 70 cm, with MDF panels - 50 cm. The use of hidden fasteners during installation will provide a modern look to the interior. Show the texture of wood

Comments:

There are a lot of methods by which interior decoration of a house made of aerated concrete can be carried out. But in any case, one should take into account the specific properties of cellular concrete, the main enemy of which is moisture. Due to the hygroscopic nature of the material, water entering the aerated concrete wall from the atmosphere penetrates into the pores, worsening its thermal insulation characteristics and limiting natural ventilation.

Despite the many options already mentioned, finishing houses made of aerated concrete should provide two absolutely mutually exclusive conditions:

1. Housing cannot be comfortable if a high degree of vapor permeability of the walls is not ensured. Only in this case, its microclimate will have a beneficial effect on the human body.
2. The high hygroscopicity of aerated concrete leads to its rapid wear with a significant penetration of moisture into the blocks. A vapor barrier is required, that is, a vapor-tight finish.

To ensure their simultaneous provision, the following rule must be strictly observed: it is impossible to finish the outer walls with vapor-tight materials, and the inner ones with vapor-permeable materials.

Aerated concrete interior walls

It is believed that the creation of a vapor-tight coating on a wall is a relatively simple task. For example, vinyl wallpaper will reduce this figure many times over. A similar effect is obtained by laying a conventional polyethylene film on the wall. But in this case, one should take into account the likelihood that condensation may form under the film, which adversely affects aerated concrete.

Traditional sand-cement plaster also improves vapor barrier tenfold. However, there is an unpleasant nuance here - due to the high hygroscopicity of the wall material, such plaster often peels off over time.

Gypsum plaster adheres well to cellular concrete. It consists of the following components:

• special (perlite) sand obtained from volcanic rocks;
• slaked lime;
• alabaster (building plaster).

Since this is a vapor-permeable coating, the problem is solved by combining materials. First, the wall is primed several times, and the previous layer of soil must dry completely. This treatment greatly reduces the vapor permeability of the surface. Gypsum-based plaster is applied over the primer, after which it is possible to finish with any suitable materials.

Back to index

Interior decoration of the house with frame materials

This finishing method is considered to be one of the simplest. Indeed, preparing walls for painting or wallpapering is a costly, lengthy and messy process, since a whole series of tedious operations cannot be dispensed with:

• surface leveling;
• their careful and high-quality smoothing;
• hardening of these surfaces.

All these operations require many different building materials, time and qualified performers. With drywall, decorative and plastic panels, which are frame materials, things are much simpler.

First of all, you need to worry about the hydro and vapor barrier of aerated concrete walls. The easiest way is to make a wooden frame from slats or bars with a thickness of 25 mm. Initially, the slats are attached to the wall near the floor and ceiling. Finding them in one vertical plane controlled very strictly and carefully.

Between these bars, several strings are pulled, showing the plane of the finish. They control the fastening of intermediate bars to the wall. The distance between the rows of bars is 50-60 cm. The frame bars are attached to the wall with self-tapping screws.

Each sheet of frame material should have three frame rails: two at the edges and one in the middle. Sheets are screwed to the frame with special self-tapping screws with countersunk heads. The distance from the screws to the ends of the sheet must be at least 1.5, and to the longitudinal edges - 1 cm. They must enter the facing material at a right angle.

Since wood, due to its sensitivity to humidity and temperature, is not suitable for every room, often not a wooden frame, but a metal frame made of galvanized steel is used.

Sometimes such facing materials are attached to the walls in a frameless way using special glue. If the wall is sufficiently even (differences in irregularities are not more than 5-6 mm), then the adhesive is applied to the sheets in a continuous layer, otherwise it is applied in the form of heaps along the perimeter and middle part of the sheets.

Back to index

Interior decoration of the house by painting the walls

It is widely believed that painting is a very simple way of finishing that anyone can handle. This simplicity is apparent, especially if the house is new. There are several reasons for this:

1. The wall must be well prepared for the upcoming painting - level its plane and achieve a high degree of smoothness. Without tedious processing of the wall with a fine sandpaper and its subsequent priming, this cannot be achieved.
2. Obtaining the desired color shade by adding color is a rather difficult task for a non-specialist.

There are a lot of building paints, they differ in composition, properties and their purpose. Before purchasing paint, it is highly advisable to consult with a specialist about the degree of its applicability for wall decoration inside the house.

When applied oil paint the degree of vapor permeability will still be significantly reduced. Recently, this finishing material has practically not been used to finish the house from the inside, and the most common option for walls is water-based paint - high-quality, inexpensive and available material for interior decoration.

A few tips for its use:

• the wall should be covered with paint in 2-3 layers;
• with a two-layer coating, the first layer is applied with horizontal strokes, and the second with vertical strokes;
• with a three-layer coating, the first and third layers are applied with vertical strokes, and the second with horizontal strokes;
• it is not necessary to wait for the previous layer to dry, the water-based emulsion is applied wet.

Recently, the use of water-based acrylic paints has been expanding. They are easy to apply, do not change color over time, and are not a source of toxic substances. Great option for those who doubt their artistic taste and design abilities.

Back to index

Interior decoration of the house: other types

The modern building materials market is distinguished by enviable diversity. For interior decoration, you can find many suitable options. Here are just a few of them:

1. Wood is the most warming material not only for the body, but also for the soul. It is used for interior decoration in the form of panels, lining, semi-logs. And if it is coniferous wood, then it will serve longer, and the house will be filled with useful phytoncides.
2. Natural and artificial stone has recently become a very popular finishing material. Used to decorate kitchens, hallways, living rooms and even bedrooms. Preliminary preparation of the walls is optional, no special laying skills are needed, beautiful, durable and strong, what else do you need?
3. ceramic tiles as facing material should be used in rooms with a high level of relative humidity. This choice implies the organization of effective forced ventilation.
4. Wallpaper is one of the most common ways to decorate walls. During recent years many new solutions have appeared, and an infinite number of colors allows you to dress the house in a truly beautiful, comfortable and environmentally friendly wallpaper.

One of the main problems after building a house of aerated concrete is to determine the optimal finishing material for interior decoration. So that the walls are not exposed to adverse influences, it is worth knowing in advance about the types of interior decoration of such material.

Features of finishing walls made of aerated concrete

Aerated concrete has a high vapor permeability. This suggests that when the air temperature drops in the thickness of the wall of aerated concrete blocks, moisture accumulates in it. To ensure the safety of the material, the vapor permeability of the wall must be reduced.

The best way to reduce vapor permeability is to impregnate the walls of aerated concrete blocks with a primer, apply a layer of cement plaster. This happens in several stages:

1. Impregnation of the surface of aerated concrete blocks with a deep penetration primer. In this case, it is worth applying these compositions in several layers.
2. Application of cement plaster.
3. Primer plaster.

Finishes

by the most in a simple way finishing is the use of frame materials. An example is plastic or drywall panels. The simplicity lies in the fact that for finishing it is not necessary to align the walls of aerated concrete blocks, it is enough just to fix the panels on the frame.

Finishing materials such as wallpaper are also often used. Before their gluing, the walls are leveled and the base for the wallpaper is applied. All these processes will require a large amount of materials, and after the repair, you will have to remove the dirt left after the surface is plastered. That is why many owners of aerated concrete houses choose frame materials.

Finishing with plastic panels

In a house with walls made of aerated concrete blocks, the frame for finishing materials is created in two layers. The first is for waterproofing, and the second for panels. For the frame, bars with a section of 25x25 mm are required. Installation begins with fixing the bars to the floor and ceiling.

Important ! All bars must be installed in the same plane so that the wall of aerated concrete blocks is even.

After installing the upper and lower bars, the threads are pulled, which serve as a guide for installing additional elements. Intermediate bars are installed along the stretched threads, the distance between which should be about 50 cm. Each element is fixed using self-tapping screws.

If you have no experience in decorating rooms with plastic panels, you should purchase start and finish profiles. They are made of plastic and contribute to a more accurate installation of the panels. They are fixed with a stapler or small nails.

Important ! After installing each panel, it is necessary to check whether they are installed evenly on the frame.

wall painting

Before you buy paint for interior decoration, you should carefully consider all the compositions presented, as they are designed for different conditions. The most common are water-based formulations. This is due to the fact that such material is not expensive and can be applied to the walls by an inexperienced person. But at the same time, it is worth remembering important points:

Water-based compositions are applied to the wall of aerated concrete blocks in several layers. In this case, the first layer must be applied not in a horizontal plane, but from top to bottom. Peculiarity water-based paint lies in the fact that when applying the second and subsequent layers, you do not need to wait until the previous one dries. Such compositions can be used in rooms with high humidity, as they withstand exposure to water.

Using wallpaper

Wallpaper can be used to create both classic interior, and for decorating the house in the original style.

Often used:

• non-woven materials;
• vinyl wallpapers;
• washable.

The popularity of such finishing materials is explained by the fact that when using them, you can choose almost any design style. But it is worth remembering that before sticking wallpaper, you need to level the surface of the wall, and also apply plaster on it.

Wall linoleum

Linoleum for floors is considered a versatile material, as it is used in both residential and public buildings. Linoleum for walls has appeared relatively recently and therefore is one of the least popular materials. But it is increasingly used in home interior decoration, as it has the following advantages:

1. Hygiene. Linoleum does not absorb moisture, so fungi do not appear on the walls.
2. Ease of maintenance. Linoleum for walls can be washed and not worry that it will deteriorate. At the same time, the coating withstands the effects of household chemicals.
3. Strength. It is quite difficult to spoil the surface of wall linoleum. At the same time, it withstands strong blows, which cannot be said about the tile.
4. Ease of installation. You can fix the material even without the skills of finishing the premises.

The disadvantages of the material include its high cost. It is also worth noting that you can not find it in all hardware stores.

Plaster

This finishing material is quite popular and allows you to create various design rooms. The advantages of plaster include ease of care for the material and a long service life. Interior decoration of aerated concrete walls is as follows:

What material to choose

To make a choice, you should first think about the operating conditions. It is also necessary to choose the right characteristics of the material. The color of the finishing material must match general design apartments. If a small amount of light enters the room, it is worth making the walls light.

To create a business style, it is better to use either materials that imitate wood. It is worth remembering the operating conditions of the premises. In the corridor, for example, you should not install materials that can easily be damaged by accidental touch.

Due to the fact that for finishing walls made of aerated concrete can be used various materials, the owner of the house can make a choice based on their own preferences. Having considered all the options presented, you can easily choose exactly the material that you like.