How to straighten a door. Interior door sagged - what to do and how to fix it? Door handle height from floor

The question of adjusting the doors is relevant at any time and absolutely for all people. No one is immune from minor breakdowns in the house, especially when it comes to such frequently used structures. How to cope with the problem should be considered in relation to specific elements of filling the doorway.

Sometimes interior doors require adjustment

Possible problems

Adjustment interior doors is required absolutely always, regardless of whether problems have already arisen or as long as the structure functions without failures. If you maintain the normal condition of the door and its elements, you can significantly extend the service life. If the moment was missed and you have to carry out an emergency targeted adjustment of interior doors with your own hands, then it is important to know what problems arise most often and where to look for their cause, ways of elimination and options for preventing repeated situations in the future.

The door does not close well... If areas of rubbing are visible on the floor, repairs must be made. door hinges and adjust the position of the blade. If there is contact with the box, set the position relative to the frame. When problems arise with fixing the closed position of the structure, you need to pay attention to the lock.
Sagged doors... Most often, this leads to sagging of the canvas under its own weight, up to the curvature of the frame.
Squeak when driving... Most likely, the grease in the hinges has simply dried out and needs to be renewed. Also, the cause may be a skew in the door frame.
The door won't open... A box can also be involved here, especially if there has been a sharp increase in humidity levels. Another option is to break the lock. Loops in this case rarely break.

Most often, the reason lies in the hinges. It is very easy to fix most of these problems with your own hands.

The most common door problems are considered to be sagging.

Since a specific situation may be associated with several factors, you should separately consider all the options and figure out how to repair various parts of the door block with your own hands.

Door frame

The most difficult situation is the door adjustment associated with the deformation of the box. In this case, the structure lends itself to the greatest destruction and sometimes fix the problem with your own hands without complete rework the box is impossible. If you ignore the situation, the canvas shifts in relation to the diagonal, begins to wear out and may even pull the racks off the wall.

How to adjust the interior door in case of a skewed frame? First of all, you need to remove the canvas from the hinges. Next, you need to take measurements and find out exactly where the displacement occurred. Be sure to check the diagonal, so it will be much easier to find a problem area where the door structure sags.

To further adjust the door, you need to remove all decorative elements and screw additional bolts into the structure to fix the correct position. After that, you need to delete the old polyurethane foam and, having exposed the spacers, foaming the seams again.

The adjustment of the door frame is considered the most difficult malfunction associated with its deformation.

Hinges

Most of the problems are associated with the adjustment of the door hinges. Several situations can be distinguished here:

The hinges are too deep... Adjustment of interior doors with such a problem is carried out in two ways. If the difference with the norm is insignificant, you need to loosen the self-tapping screws that fix the hardware plates. When deepening by more than 0.5 mm, a backing, for example, made of cardboard, will help to raise the hinges.
The hinges protrude above the patch or canvas. In this case, the canvas will not fit snugly against the box. In order to remedy the situation, you just need to remove an additional layer of material from problem area... It is convenient to do this with a miniature grinding attachment.
Creak. The problem may be due to dirt getting into the hinge. In this case, it is necessary to clean the parts and lubricate them with oil or silicone. If the door sags slightly at the same time, you need to adjust the hinges. Sometimes the problem lies in the pivoting mechanism itself, in which case it will be necessary to repair the door hinges or complete replacement details.
The door sagged. If the door sags, the reason may be that the hinge fasteners are loose. In order to lift the sagging door, it is necessary to tighten the screws tighter. If this is not the case, you can put a rubber gasket under the canopy. In some models, you need to knock out the axle. In plastic blocks, adjustment is made by tightening the hinges with a hex wrench.

When the door sags the best way - this is to tighten the self-tapping screws on the hinges

Handles and locks

If the canvas does not lock in the opening when closing, check if the position of the tongue in the lock matches the hole in the counter plate. If not, the plate must be moved to the correct level. The second option is to correct the position of the deadbolt.

To troubleshoot locking fittings, it is necessary to determine the exact problem

How to adjust the door lock if, on the contrary, it sticks? If the reason is not that the door sagged under its own weight, then you need to do the following: first, look at how the latch tongue moves, it may be sufficient to just lift it with a screwdriver. If the problem persists, disassemble the handle structure and check the condition of the internal mechanism. Its parts may shift or break, in which case replacement is required. If the handle turns tight, you may need a banal lubrication of the mechanism.

To prevent the doors from breaking, you need to do a preventive inspection of the structure and fix breakdowns before their direct manifestation.

With proper care door structure you shouldn't have such problems. If breakage cannot be avoided, now you know how to fix it yourself.

If in your house the doors start to open randomly accompanied by a squeak, or vice versa, it takes a lot of effort to close them, it's time to think about what to do if the door is warped and how to make repairs.

Getting rid of the squeak

To remove unpleasant squeaks, try oiling the door hinges. This is done as follows: put some kind of wedge on the bottom of the door, and then slightly lift it. Gaps will appear on the hinges, into which you need to drip some oil. You can use a pipette for this. So that the trouble does not happen again, do not forget to repeat the procedure periodically.

Machine oil can be replaced with a piece of soft lead a simple pencilwhich perfectly functions as a lubricant. Under pressure door leaf the slate will break, and the door will stop making creaks.

Arbitrary opening (closing)

If you notice that your door began to open or close from the slightest draft, this indicates that the hinges are not fixed correctly. They must be fixed in a strictly vertical line. And if there is an arbitrary opening of the doors, you need to rearrange the hinge from above closer to the inner side of the jamb, and when it is closed, the same must be done with the lower hinge, or put something under it.

Misaligned hinges can also cause the door to skew or jam. To solve the problem, you will have to remove the old screws from the hinges and replace the longer ones in their place. If you decide to keep the old screws, you will need additional reinforcement of the sockets. It is quite simple to do this: you need to fill the loops with pieces of wire wool, or drive in a wooden cork, previously greased with glue. Also, the door will stop jamming if the hinges are recessed into the slots.

To prevent the skew of the door leaf, it is necessary to drown the hinge located opposite the skew. If the above measures do not bring the desired results, you will need to remove a small layer of wood on top. The same should be done with the door swollen with moisture.

In some cases, the problem can be solved by walking along the end of the door with coarse-grained sandpaper. To do this, you don't even have to remove the canvas from the hinges. However, if it is necessary to remove a large layer, the door will still have to be removed.

The door is removed from its hinges in the following order: place a solid object under it, lift it, holding it by the middle. Slightly swing the canvas on the hinges, lift with the lever and remove.

It may well be that the door periodically shrinks and swells depending on the season. Then you need to remove the extra layer of wood when it swells, and during drying, nail a gasket, the thickness of which you can adjust. The gasket is made in the following way: take a rectangular piece of copper or brass sheet. Its length should be equal to the double thickness of the door leaf, and its width should be approximately 4-5 cm.

This rectangle is fixed with screws or nails to the vertical end in the center of the door, and its other half is bent outward and its end is rolled up. Cardboard or several layers of paper are placed in the space between the plates. With these simple steps, you will ensure that doors close without interruption. Based on its condition, you can increase or decrease the lining.

Difficulty closing (opening) doors

However, there are often situations in which, on the contrary, closing and opening doors is somewhat difficult. Initially, you need to find out the location of the tongue. If such a defect is present, then there will be scratches on the strike plate. If there are no scratches, rub the tongue with chalk and you will see the place that it touches. If damage occurs under the bar, then the reason is the door subsidence and it can be solved by fixing the hinges.

If the hole moves to the side, it is worth unscrewing the striker plate, and then enlarging the hole with a file. Also, a large gap between the door and the vertical bar can prevent the door from closing. To solve the problem, remove the striker plate, put a gasket under it. Choose the thickness of the gasket based on the situation.

Rotting door frame

If decay or loosening of the door frame occurs, you need to change the damaged element, then securely fix the box to the wall and make sure that there are no gaps between the wall surface and the frame. If there are gaps, they need to be caulked, and then covered with plaster over a fine-mesh metal mesh.

That's all the main troubles that may lie in wait for you when operating interior doors. Now you know about the ways to eliminate them, and, accordingly, you will no longer have any special problems.

It is difficult to imagine any dwelling, no matter how many rooms it has, without interior doors. Above all, this building envelope is essential for bathrooms and washrooms. Therefore, it is important that the interior doors work properly for a long time. For this purpose, at the final stage of the door installation, it is adjusted.

In addition, old doors often need to be adjusted. It is with this process that we will try to figure it out in our article. But let's start with a general description of the structural elements of an interior door.

Often, homeowners who are not naturally deprived of the ability to manual labormake a decision about self installation and adjusting the doors of the rooms of your house. In principle, such work can be done by hand. But for beginners, for a start, it is important to know what the interior door consists of.

The main structural element of any door is the leaf; it is on it that they first of all pay attention when buying a door. Another name for the canvas is a sash.

Installation of the door and its operation are impossible without a box, which is installed in the doorway, and the canvas itself is already attached to it. The frame is an original structural element of each specific door, which coincides with it in color scheme ... This means that the installation of a new sash in old box not possible.
Often the box is included with the finished canvas. It has three or four elements. If the door is planned without a threshold, then the box has a U-shape, it includes 2 long vertical beams (hinged and false) and one short horizontal (lintel). If necessary, the design of the box includes a threshold, in this case it will look like a closed loop.

The decorative function is performed by the casing. It is he who closes the seam at the installation site of the door frame in the wall opening.

If the wall thickness is greater than the thickness of the door frame, then it is necessary additional plank... It is also a decorative element that matches the color of the canvas.

An important detail of the doors is the fittings, which include two hinges on which the canvas is attached to the box, a latch and a set of handles. For doors installed, for example, in a bathroom or toilet, a locking device is also provided that allows you to close the door from the inside.

These are the main structural elements interior doors.

Adjustment of interior doors as the final stage of installation

So, the process of installing an interior door is coming to an end. The box is installed in the opening, and the sash is suspended from it. At this stage, before foaming the gap between the opening in the wall and the beams of the box, it is necessary to adjust the door. First, a primary inspection is carried out for opening and closing the door, the uniformity of the distance between the sash and the frame. There may be several reasons why the gap size is different.

The gap can be so uneven that the door will hit the jamb from above or below.

If no violations are found during the inspection, then they proceed to a more thorough check, during which several major malfunctions can be detected. Let's consider each of them, the reasons and ways to eliminate them separately.

Can't close the door

This is the most common problem. There are several reasons that prevent the normal closing of the interior door.

This is mainly due to skewed door frame, which is due to its incorrect installation, in the process of which the bars were insufficiently fastened together or the correct proportions were not observed when connecting the horizontal and vertical bars.

You can identify the presence of a skew of the box using a level or plumb line. If the case is really in the box, then it will need to be removed. It is necessary to check whether the cut of the joints of the beams is even, to connect them to each other again, strictly observing an angle of 90 degrees. Fasten all joints with at least two screws. As a result, you should have an even letter P with firmly connected corners.

They can either be insufficiently recessed in comparison with the surface of the box or canvas.

In some cases, you can deepen the loop by twisting the screws in it, but this does not always work. If it does not help, then you will have to unscrew the hinges and deepen the attachment point with a chisel or grinding.

Deepening the hinge grooves by grinding

The hinges can also be incorrectly installed in the horizontal plane: they are deeply removed from the front of the canvas. Then they will need to be removed and moved closer to the front of the sash.

The door gets stuck in the opening

This means that the door can be closed without problems, but it is not easy to open it. There are two main reasons for this problem.

First, the fasteners of the box beams are not tightened enough... Everything is simple here: you need to tighten the self-tapping screws that secure the pretend beam in the opening.

Secondly, excessively deep grooves can be prepared for the hinges.... To cope with this problem, you need to remove the door, remove the hinges and put cardboard under their sashes.

Loosely closed door opens or closes automatically

This happens when the door frame is not strictly vertical. If its top is overwhelmed in the direction where the sash opens, then the door opens. When the top of the box is piled in the opposite direction, the door closes. This can be fixed by leveling the box, especially the hinge bar. You can use a plumb line as a guide, but a long level is preferable. The use of a short level is also allowed, for this it is worth binding it, for example, to a rule. Align the box and secure it to the opening.

In addition to problems with the frame, hinges or door leaf, inaccuracies in the installation of locking mechanisms can be identified.

Adjusting locks and door handles

A common problem that arises when installing a door lock is its insufficient deepening. As a result, the side plate of the lock or the doorknob interferes with the doorframe. The way out of this situation is to deepen the hole for the latch or lock mechanism.

Sometimes the screws of the lock or the latch are not screwed in enough, so the mechanism dangles in the groove. The solution is simple - tighten the fasteners.

Adjusting old doors

Despite the fact that adjustment is the final stage of door installation, it is often necessary to carry out it for old doors as well.

One of the main and common problems of new interior door structures is the creak of the hinges. Sometimes this is also observed at new doors. To eliminate this problem, it is necessary to lubricate the hinges with machine oil. For this, a wedge is placed under the door, the door is raised in order to partially remove it from the hinges. Oil is pipetted into the gap that appears in the loop, which can be replaced with a piece of graphite lead of a simple pencil.

Another common problem with older doors is skew. There are several reasons for it.

For wooden doors, skewing can be associated with swelling of the leaf. In this case, it is necessary to determine the place of bulging. For this, paper is applied to the alleged distorted area and the door is closed. The place where the trace from the carbon copy will remain is the section of the bulging of the canvas. It is he who must be cut off, and the door itself must be painted over, as described in the case of new door with broken geometry.

For heavy doors, for example, made of solid wood, the skew can be associated with deformation of the hinges. This is usually caused by the wrong buttonhole.

Note! Heavy wooden doors should be installed on not two, but three hinges.

There are several ways to correct skewed loops:

replace with new, more durable ones;
install additional hinges;
unscrew the screws from the hinges and replace them with longer ones;
strengthen the nests for the screws with a cork greased with glue;
install washers in the hinges, so that the door rises a couple of millimeters in the center of the hinge.

Washer installation

The skew of the door leaf can also be caused by a change in the geometry of the opening in the wall. Without replacing door elements, this defect can be eliminated as follows:

undermine the door in the place of skew;
remove and rearrange door frameby adjusting the joints of the bars, observing an angle of 90 degrees.

In the latter case, you need to focus on the building level, and the box must be firmly fixed to the doorway. For this, two holes are made through the box in the wall from the side of each beam. The depth of the holes in the wall must be at least 50 mm. Pins made of metal or wood are driven into the holes. Wooden fasteners are pre-lubricated with glue.

Final word

Installation of the door and its adjustment can be done independently, but at the same time it is necessary to observe maximum accuracy so as not to spoil the canvas or frame as a result.

Note! If a wooden door is planned or already installed in your house, then remember that its prevention must be carried out annually.

If you have doubts about your own abilities, then it is better not to risk it and entrust the entire process of installation and adjustment of door installation to professionals.

Video - Adjusting doors

A skewed entrance or interior door does not fulfill its functional properties, closing poorly, without isolating individual rooms or the common space of the apartment. Knowing what to do if the door is warped, you can independently eliminate the emerging structural or operational problems in a short period of time, give the door leaf a second life, saving your finances and time. Most of the defects are successfully corrected at home, without the use of expensive equipment and tools and without the involvement of expensive services of professional craftsmen.

Skewed doors are the result of a number of operational or technical properties of the product. Therefore, it is necessary to immediately determine the cause of the appearance of such a deficiency and, first of all, try to eliminate it. There is a difference in the features of the operation of doors made of wood, metal and combined materials.

Over time, even the most high-tech and reliable samples of doors need inspection and preventive maintenance: lubrication and adjustment of the hinges, cleaning the surface, coating functional elements with special compounds.

Note! The cause of malfunctions or damage to the door structure is not always improper operation or mechanical failure. Often, the problem lies in the quality characteristics of the product, violation of its manufacturing technology, installation or storage conditions. Therefore, door kits should be purchased only from reliable and trusted manufacturers that guarantee a certain service life and provide certificates of compliance with Russian standards.

Elimination of skewing of a wooden door

The main reasons for the skewing of doors made of natural wood are high humidity, constant dampness and significant temperature changes. This is usually the most common problem for owners of summer cottages, rural houses or country cottages with seasonal use. Due to the lack of heating in the winter season, the internal elements of buildings become damp and freeze, and when heat comes, condensation appears in them. Summer heat causes moisture from the wood to evaporate and warp. For timber structures, such conditions become a real test of strength.

Note! Even in apartments and houses with a constant mode of residence, wooden doors require special protection against distortion, the use of penetrating impregnations and effective coatings.

Already skewed wooden door can be corrected only by first removing it from the hinges. It is necessary to prepare a plane in advance and remove extra millimeters of wood, including paint or varnish, from the ends of the canvas. If the door is badly warped, then you can repair it using felt or rubber gaskets. The width and dimensions of the gasket are selected on an individual basis, taking into account the actual state of the structure and pre-measured measurements. The tapes of the cushioning material are fixed with small nails, special glue, furniture or construction stapler. The fastening technology depends on the characteristics of the door leaf and the level of its operational load.

Elimination of skewing of a metal door

Any metal door designs are more resistant to negative climatic phenomena and difficult operating conditions. But there are situations when even the most reliable metal constructions... The most common reason for changing the properties of the web can be the use of too heavy multi-layer steel in the production or a technological violation of the thickness of the product. First of all, they may not stand door hinges... They change their technical properties, sag or break. It is almost impossible to eliminate such a drawback as an incorrect and incorrectly calculated door design on your own.

Over time, the hinges can simply loosen and wear out. It is enough to change them and the door will serve its owners for many years to come. The main thing is to pick up in a hardware store right size loops and make sure of their quality.

The most difficult and serious situation is the skewing of the door as a result of significant shrinkage of the house and its individual structures. As a rule, such a problem is associated with non-compliance with construction technology or premature commissioning of a house. In such a situation, you should change metal door on wooden canvaswhich is easier to adjust and fix when changing openings.

The annoying problem of sagging doors

The annoying problem of sagging doors, especially wooden ones, can occur for a number of reasons.

The root causes can be different, but each of them leads to the fact that the door may not close at all over time, scratch the floor and completely stop serving. It is permissible to correct the situation with your own hands.
Interior door sagged what to do? Video

Replacing or adjusting doors if the interior doors have sagged

Replacement and adjustment of doors
Repair of doors is required over time to any overlap of the opening of adjacent rooms.
The door structure is not only a decorative element of the interior design of a dwelling, but also the main functional detail, which is simply indispensable in everyday life for a comfortable stay at home. After all, the door is so necessary in buildings of any type of use:
Protects the room from drafts;
Separates adjacent rooms relatively functional purpose;
Creates a cozy atmosphere and plays a decorative role in stylistic design.

Not only a serving door can fail, but also a completely new product due to not correct installation, shrinkage of the structure as a whole, and so on.
In many cases, households begin to think about the prompt replacement of the door, which has ceased to be visually attractive, and has lost a number of functionality. If the question arises as to whether it is necessary to replace the block with something new, or to start repairing the doors, then know that even an inanimate interior detail requires attention and care.
The product may cease to please for a number of reasons that can be corrected with your own hands:
The door leaf made of natural solid wood cracked.

Such a visual misunderstanding is corrected by restoration work or decoration, the list of which is simply unthinkable for selection. The whole process, both restoration and decorative finishing door leafs, reproduced with their own hands in everyday life with little financial costs.
If the restoration implies a thorough list of works, then it is permissible to reproduce decorating the sash with your own hands without even removing it from the hinges: decoupage, painting and so on.
The structure of the ceiling was loose.

You can also strengthen the door frame with your own hands at home. Why is it just worth disassembling the block using a simple tool that everyone has home master or borrow from a neighbor for a short period of time. In this case, you may only need to strengthen the door frame at the installation site, tighten the hinges, or pull off the canvas itself, that is, strengthen loose or cracked panels wooden structure.
Disgusting, cutting hearing and nerves, creak.

Lubricate the door

The squeak of the opening or closing sash is often caused by the friction process of the pins, which are the elements of the door hinges. The reason for the squeak may also concern the poor fastening of the loops themselves to the loop bar or the end of the canvas.
To eliminate the sharp sound, it is recommended to view the fastening of the loops and lubricate them with machine oil, or use graphite, pieces of which are inserted into the loop gaps.
Doors close poorly.

The wood door does not open or does not close, then its problem is hidden in the conditions of internal use. Over time, any product made from natural solid wood can swell, that is, significantly increase in size around the perimeter. The door still does not close due to a violation of its geometry: it swelled, led, sagged the door, loosened the hinges, led the box, and so on.
The reasons for the fact that the sash does not coincide in geometry with the box may be mass. If the door has already sagged thoroughly, then it is recommended to tackle the issue seriously, which we will talk about below.
Possible reasons malfunctions

If the structure sagged slightly or fairly, then the following visual circumstances of the functional activity of the unit indicate this:

The first slight scuffs of the door sill, due to the fact that the doors do not close well;
Damage to the flooring, when the door does not close at all, that is, it does not fit snugly around the perimeter of the box;
There are clear gaps around the perimeter.

Upon confirmation of at least one of the above violations in the quality service of the floor unit, there is only one conclusion - the door has sat down with a violation of the geometry of the fit. Before at least some door adjustment is undertaken, it is worth examining the unit for a malfunction, and only then get down to work.
The main reasons why an interior door from a natural solid wood or from another material for internal use does not open include the following misunderstandings:

Move the hinges away from the installation site;
Deformation of the door frame;
Violation of the geometry of the sash itself;
Swelling of a canvas made of natural solid wood.

It is permissible to correct many shortcomings with your own hands, but for work it will be required in all the listed cases:

PVA glue or other adhesive for working with wood;
Screwdriver or screwdriver;
Self-tapping screws;
Plane, chisel;
A hammer.

You may also need another simple home tool, which, if you do not have it in the pantry, it is permissible to ask for a loan from a neighbor.
Inspection and repair of hinges

First of all, if the door has sagged, it is recommended to inspect the hinged awnings, since the reason is most often hidden in them. To correct and return the functionality of the sash, repair of the doors is not required, you just need to remove the canvas from the hinges, inspect and correct them. The answer to the question of how to remove the door from the hinges is simple:

Open the sash;
Substitute a crowbar or other convenient object under it;
Using a crowbar (or with your hands), lift the canvas from bottom to top.

Thus, the sash will be freed from the hinges, but now it must be safely held so as not to damage it. For these purposes, if such works are reproduced for the first time, invite a household member to help you, who will at least support the canvas so that it does not fall over.
Usually, the hinges are fastened to the hinge bar (door frame rack) using wood screws. If the door sags strongly, then:
It is recommended to drive wood wedges under the unscrewed screws into the holes, then mount the hinges on the screws in place.

Pre-dip the wedges in PVA glue (or joiner's). To secure the hinges, use longer fasteners, and hang the door itself 24 hours after the adhesive has dried.
If the situation has not been corrected with the overlap sagging after the hinges have been reinforced with wedges and new self-tapping screws, it is recommended to change the previous hinge installation location.

In this case, you can use the old hinges, but place them on the hinge beam in other places, as well as at the end of the sash itself.
Hinges are cut in new installation locations in the same way. The main thing is to correctly calculate the vertical axis of the location of the looped canopies, and the distance between each other. The grooves in the wood are made using a chisel and impact with a hammer. The chisel is best used with a straight blade.
If the door sags in a short period after installation, then the problem lies in the large weight of the sash itself, which the hinges cannot withstand.

The situation can be corrected simply by adding additional loops. You can cut in a third loop by placing it at a distance of about 10-20 cm under the upper canopy. Or install an additional loop by moving the top one slightly higher.
If the door has sat down after a long service life, then this may indicate wear on the hinges.

With a long period of service, the core is worn out in the hinges, which can be simply replaced. But this may not improve the functionality of the old hinges, as they also wear out over time. Better to buy new hinges.
With a slight sagging of the door leaf, the hinges can not be replaced, but slightly corrected.

In this case, the doors are adjusted using a steel ring, which must be laid under the metal core of the element. Bearing ball suitable size regarding the diameter can also help.
If this is not enough to correct the situation, then a substrate can be made under the hinges, which will slightly lift them from the loop bar.
Do not forget that after manipulating the looped sheds, it is recommended to lubricate them with machine oil for prevention.

We identify the deformation of the door frame

After you have managed to adjust the hinged door, it may happen that it does not open or closes poorly. So the hinges were not entirely to blame here.
The problem is most likely in the absence of the required functional gap between the frame of the structure and the sash.
To identify such a problem, you will need a building level, which checks the vertical and horizontal of the structure. During the closing process, the door can cling to the box in any part. If a clear violation in the installation or a slight deformation of the box is determined, which is possible after a long period of operation of the unit, then the problem is solved by lightly cutting the fabric of the structure exactly at the place where the problem occurs.
It is worth noting that before, how to tackle the cutting of the door leaf, you need to thoroughly make sure that it is the box that has not succumbed to strong deformation. Otherwise, efforts will be reproduced in vain, and the canvas will be damaged.
The fundamental deformation of the frame is the most difficult problem associated with the door structure of the floor. Adjusting the doors in this case will not help if you do not completely redo the box. After all, how to adjust the door, if the base of the floor has succumbed to movement. If we ignore the deformation of the box, then in addition to the displacement of the canvas diagonally, over time the racks will come out of the plane of the opening.

The skew of the frame is corrected by the following manipulations:

The overlapping sheet itself is removed from the loop awnings;
Measurements of the vertical and horizontal of the rack mounting are carried out;
The diagonal of the opening is checked;
The place of displacement is found;
All decorative elements are removed from the ceiling: add-ons, platbands;
Fixing bolts are screwed into the frame structure, which will correct the situation;
Removed from gaps construction Materials: plaster, polyurethane foam;
In the necessary places, spacers are installed for the frame, which in the future will hold it in the correct position;
Finally, the gaps are foamed and plastered again;
Platbands and extensions are installed in place.

Violation of the door leaf geometry

Natural solid wood is a very valuable product, especially in a home environment.
Natural materials have always been valued. If the table is made of solid wood or other object decorative design dwellings do not require a certain degree of attention and constant care, then if a wooden door has sat down, you may be to blame here.
Doors made of wood do not close well due to their swelling or, conversely, drying out. This can happen because:

That the humidity rate in the room is not maintained;
The block may not be treated with protective agents or special impregnations;
The installation itself could occur, for example, in winter time years when the unit did not have time to acclimatize in the indoor heated room;
Installation of solid wood structures is not recommended in the openings of rooms with constant temperature differences and humidity fluctuations: bathrooms, showers, and so on.

If the door has already sagged, then you should not immediately run to the construction center for a new replacement from the combined material. Repair of solid wood doors natural wood do it yourself very simply using a regular plane or more modern instrument.
You can adjust the sash to the parameters of the box by cutting problem areas on the canvas. Before starting work, you need to do at least visual measurements:

Close the door;
Assess the dimension of the existing gaps;
Remove the door from the awnings;
Sew the harness in certain places.

Any flaws in the design of overlapping openings of adjacent rooms can be corrected with your own hands. If the methods of correction do not lend themselves, then it is better to invite a specialist to your house. After all, it is cheaper to eradicate faults immediately, since over time they turn into major breakdowns.

1 /5 (2 )