A furnace from a cast-iron bath to a bath drawing. Do-it-yourself stove for a bath from a cast-iron bath. Oven and combustion chamber

There comes a time when plumbing, due to its appearance or malfunction, becomes unusable. But, replacing it with a new one, you should not rush to throw it away. Summer residents and home owners can easily make a garden stove from cast iron bath, which in terms of strength and service life will not be inferior to factory models.

Advantages of using cast iron

This type of metal is considered to be one of the best furnace materials. Its main advantages include:

1. environmental safety. Does not emit when heated harmful substances.
2. Temperature resistance. An outdoor stove made of bricks can begin to crumble after a few years.
3. High thermal conductivity. A cast iron fireplace warms up a room much faster than one built from other materials.
4. Strength . Cast iron is the leader among metals in terms of strength. Even steel ovens are less reliable.
5. Ease of use.
6. fire safety.

The disadvantages of cast iron that you should pay attention to are brittleness and susceptibility to corrosion. In the first case, unnecessary mechanical influences should be avoided, in the second case, the surface should be treated with special solutions.

A home-made cast iron structure will not turn out very beautiful, so it is recommended to overlay it with brick or stone.

Preparation of materials and tools

To create such a miracle oven from the bath, you need to prepare:

• angle grinder (grinder);
• 2-3 circles for metal with a thickness of at least 1 mm, a diameter of 12.5 cm;
• electric drill;
• drills for metal with a diameter of 9, 11 mm;
• grinding wheels;
• files;
• hammer;
• level;
• construction gun (for applying sealant);
• plumb;
• putty knife;
• Master OK.

Materials you will need:

• iron or steel sheet 5 mm;
• refractory red brick;
• grate;
• sealant;
• clay;
• sand;
• metal corner;
• bolts with nuts, washers;
• chimney pipe with a diameter of 12 cm.

Photo: the material is prepared, it remains to choose the purpose of the furnace and get to work

When all the materials, tools are collected, you can start cutting the container. For convenience, it can be turned upside down or laid on its side.

Users often search:

You need to wield the grinder carefully so as not to damage the surface.

Before you start sawing the bath, it is worth considering a few nuances:

1. Marking will simplify cutting the product.
2. The first layer of enamel is removed strictly along the drawn line. This will help prevent chipping at the edges.
3. The next step is to cut the cast iron. Do this gradually, in small pieces of about 10 cm, so as not to overheat the grinder.
4. When the bath is already sawn in half, supports are placed under each part. They will not allow parts to fall and damage the tool, material.

According to experienced builders, it is better to work with a grinder at an angle. So the enamel does not start to peel off and all the cuts will turn out to be smooth without burrs.

Subject to the use of a high-quality grinder, the processing of cast iron will take no more than 1 hour.

For a barbecue, you will need two halves of the bath: one part will serve as a fuel loading chamber, the other is necessary for cooking. For a sauna stove or fireplace, one half will be enough.

Step-by-step creation of a furnace from a bath

Without building experience, it is worth consulting with a specialist about all the intricacies of masonry and installation of parts, but it is better to perform work under the supervision of a master. So the product will turn out to be of high quality and standards fire safety will be observed.

As for the construction of the foundation, its type depends on the total weight of the furnace:

• For structures over 700 kg, a monolithic or tape base with a depth of 50 cm or more should be equipped. A formwork is constructed around the perimeter of the pit and covered with a layer of crushed stone or broken brick. Compacted. Filled with concrete.
• For ovens small size enough brick foundation. It is recommended to purchase cement grade not lower than M300. Bricks are placed with an edge, fastened together with a solution.

Now consider detailed instructions for the manufacture of each of the furnaces with different purposes.

For a bath

To create in the steam room the necessary conditions, the design must meet the following requirements:

• have a high thermal power;
• regulate convection currents;
• produce enough steam.

The procedure for building a sauna stove:

It is important to note that the foundation must have a protrusion on the borders of the furnace of at least 50 cm, and 1–1.5 m of free space must be left in front of the furnace.

An interesting idea is to make a bath stove from both halves of the bath. The second part will be needed as an extension for heating water, or you can lay out a Russian heater from it.

For cooking

On suburban area not to do without a barbecue or a brazier. And the opportunity to bake delicious bread, fry meat in the fresh air makes the owners equip small outdoor ovens on the territory.

Here is a description of how to build a barbecue step by step from the bath.

The sequence of work is as follows:

Some masters leave the barbecue in this state, but in order for your oven to look beautiful, you still need to do exterior finish.

There are several options:

1. Clay whitewashing.
2. Whole masonry ceramic tiles or pieces of it.
3. Surface finish natural stone pre-cut into pieces 10 mm thick.

The materials are attached to the furnace with heat-resistant adhesives.

A good solution is to install the chimney to the stove through the drain hole of the bath, expanding it in advance, and only then weld it to the steel sheet.

For heating

In the country, it is easy to build a fireplace from half a bath. He can be:

• Built into the wall. Suitable if the house has brick walls. Significantly save free space.
• Reclined (half-open). The firebox is located at a considerable distance from the wall. This fireplace does not need a separate foundation, it is mounted directly into the floor. Has good draft, the built-in ashpit.

The advantage of using a cast-iron bath for the furnace part is that the fireplace is obtained in the form of an arch and eliminates complex brickwork. The hole for the chimney is made at the top of the tub. The outer part is decorated with a fireplace portal.

When building a semi-open fireplace, the following recommendations should be taken into account:

1. A cement mortar up to 15 mm thick is poured under the base.
2. A metal mesh is laid on top.
3. A layer of waterproofing is applied.
4. Asbestos cardboard type insulation is laid.
5. A pedestal under the firebox is being built. Suitable brick, aerated concrete. The binder mixture is cement mortar or heat-resistant glue.
6. The structure is plastered. You can finish it with stone, ceramic tiles.
7. Between the lining and the fireplace insert, a gap is left for the convection heating system.
8. The chimney pipe is mounted in the hole made, removed through the ceiling, the roof. Often made in the form of a sleeve.
9. From the inside of the firebox, the chimney is sheathed with heat-insulating non-combustible material.
10. Finishing the bottom of the fireplace.
11. The product is closed from the side and from above with a frame made of duralumin corners connected by self-tapping screws.
12. The frame is sheathed with drywall.
13. Holes are made in the lining for air ventilation.

When installing a chimney, it is important to take into account that with a pipe height of up to 5 m, the deviation angle is 45 0, over 5 m - no more than 20 0.

For waste disposal

An unusual decision to build from old bath waste incinerator.

The principle of its construction is similar to a street barbecue.

Scheme of placement of the furnace on a brick base

The alternative is to remake the old heater by removing all parts except for the grate and body. Part of the cast iron is welded to the base from the inside to strengthen the structure.

In such a fiery trash can, you can load waste directly from above. When burning, the stove should be covered with another part of the bath so that the smoke does not disperse throughout the area.

So do not rush to get rid of things that are out of order or have lost their appearance. In skillful hands, even an old bathtub will get a second life, it will become a functional stove that will last for many years.

It is always a little pity when some old things that have served faithfully for many years become unusable. But the natural domestic ingenuity often allows you to breathe a second life into seemingly “veterans” who have served their time. For example, very often a sauna stove is made from an old cast-iron bath. The popularity of such a solution is added by the undoubted advantages that such a non-trivial material as cast iron has.

• practically unlimited service life. Even the enamel that covered the baths is practically very difficult to destroy. This is explained quite simply. IN Soviet times the enamel coating was made two-layer using quartz sand, which, when baked, formed a heavy-duty composition;
• a significant indicator of heat capacity, as well as the accumulation and release of heat;
• high resistance to corrosion.

Necessary materials and tools

• in fact, an old bath, preferably cast iron, although steel can be used with a slightly lesser effect;
• steel sheet with a thickness of at least 6 mm;
• steel pipe;
• several bricks;
• metal fasteners;
• angle grinder, she is a grinder;
• welding machine.

Option number 1, universal

Step #1

Cut the tub in half using a grinder. Cast iron is a brittle material (and this is perhaps one of its few drawbacks), so when making a cut, care must be taken to avoid chipping the material. It is necessary to ensure that the grinder does not heat up too much, for which technological breaks are arranged.

Step #2

Cut a metal sheet 6 mm thick. or more according to the size of the part of the bath prepared by the first step, which in the final design will be located below. Having previously outlined, cut a hole on the sheet according to the size of the existing pipe. Then weld it in place. Thus, a chimney is gradually formed.

Step #3

Make a hole in the upper part of the bath, then put both halves on top of each other with a layer of metal sheet. The pipe must be secured either by welding or using heat-resistant oven sealant. With the same sealant, it is necessary to process the junction of the metal sheet to the halves of the bath, which will avoid possible smoke. The edges of the bath must be securely connected with fasteners.

Step #4

The basis of the future furnace is almost ready. Now it must be installed on the brickwork to give the structure stability and ease of use. The ends of the future furnace, first of all, for decorative purposes, it is recommended to sheathe either with an ordinary iron sheet or with a corrugated one, which looks even more attractive.

Step #5

Make metal doors for the firebox and the chamber for stones. In order to improve the air supply and, as a result, better burning of firewood, it is necessary to make a number of holes in the firebox.

Step #6

The resulting universal oven can be used for a variety of purposes. In order to install it in the bath, it is necessary to make the most minor additions, namely, place stones in the upper part; connect to an existing chimney or bring an existing pipe outside the steam room.

Option number 2, specialized for a bath

When using the oven only for a bath, a simpler design solution is possible, which includes actually refusing to use the second part of the bath. In fact, the first half of the bath is used, which is lined with ceramic oven bricks.

Inside the bath, either gas bottle, or a metal drum with a diameter of about 40 cm. A chimney is connected to it, welding it.

Stones (7-15 cm in diameter) are poured into the free space of the half of the bath, left from the firebox. As a rule, pink quartzite or granite is used for this.

Video review :

Masonry is carried out to the height of the bath using clay mortar. The main feature is the joining of two materials that are very different in terms of thermal expansion - brick and cast iron. To do this, it is necessary to provide for expansion joints, in which, as a rule, basalt cardboard or asbestos is used.

After performing masonry work for decorative purposes, you can tile the surface.

After repairing and replacing the old bathtub with a new one, it often happens that the hand does not rise to throw out another solid cast-iron product. But what to do with it next? People who have a dacha usually take out things that have become unnecessary on their own. suburban area, acting in this way with the expectation of necessarily finding some use for them in the future. We will tell you how to make a sauna stove from an old cast-iron bath.

Cast iron bathtub that had to be replaced with a more modern version may already look not too fresh on the outside. But it still remains a strong and durable container of a sufficiently large volume, which you want to somehow adapt for your economic needs.

In the country, a cast-iron bathtub can find many uses.

Most often in the country, a bathtub is used as a reservoir for water used for irrigation, or as a container for making compost. But there are other ideas as well. For example, from a bath you can make an original garden furniture or build a small artificial pond, which will become a real decoration of the site. And here much depends on the imagination of the owner of the cottage. And viewing the photos of the options already implemented will help you navigate the situation and find something extraordinary for yourself. But you can also make a stove from a cast-iron bath, because in the store they are quite expensive. Cast iron is a perfectly suitable material for this purpose, which differs in:

• high strength;
• good thermal conductivity;
• resistance to high temperatures;
• unpretentiousness in operation.

Decorated cast iron bathtub for collecting water in the country

Of course, all cast iron products, despite their strength, are quite fragile. Therefore, they must be handled with care and avoid applying excessive mechanical forces to them. But still, a good furnace structure will turn out from an old bath. From it you can make one of several options for stoves for summer cottages:

• street garden;
• fireplace for a country house;
• for a bath.

All these options are quite doable with your own hands, and watching a video on this topic will help you better understand the process of actions that will be required for the independent construction of the furnace. The bath itself will have to be cut into pieces. But sawing cast iron is not an easy task, requiring certain skills, effort and time.

How to cut a cast iron bath?

This operation must be approached with all responsibility. You need to act very carefully so as not to damage the cast iron product. For cutting, you will need a grinder and several metal discs. Work, if possible, is best done not indoors, but on the street, doing it in a respirator, goggles and construction gloves. It is necessary to follow the following sequence of actions:

• first of all, the marking of the future section is made;

Sawing the tub carefully to avoid chipping

• then, along the entire outlined line, a layer of enamel covering the cast-iron base of the bath is first incised to avoid the formation of chips along the edges;
• after that, they begin to cut the cast iron itself with cuts of 10-12 cm, taking breaks when the tool overheats;
• after sawing about half of the bath, you need to put supports under each of the parts, otherwise at the end of the work they can close and damage the tool.

Advice. It is desirable to cut the cast-iron base at an angle. In this case, as a result of the reverse stroke of the disc, the enamel will not peel off, and the cut itself will turn out to be even. WITH good tool on hand, the work of cutting a cast-iron bath into pieces can be done in about an hour.

A stove for a bath from a cast-iron bath: how to make it yourself?

It is much more difficult to build a sauna stove than to install an ordinary garden stove on the site. After all, it should be not only effective, but also safe. Therefore, you need to responsibly approach the installation of the stove in the room. And in order to quickly navigate the process necessary action, you can see the photo or read the relevant video material.

Attention! The construction of a bathhouse and any other stove requires compliance with fire safety rules. For its proper equipment, you need to have at least minimal knowledge and experience. It is better even before starting work to first consult on this issue with a specialist, finding out all the subtleties and nuances.

The furnace structure in the bathhouse must comply with the following parameters:

• sufficient thermal power with the possibility of its change;
• the ability to accumulate heat and produce steam;
• the ability to regulate convection currents.

For the construction of the furnace, a cast-iron bath is suitable standard sizes

After cutting the bath, you can begin to build a furnace structure. In this case, you can use only one half of the cast-iron container for the equipment of the furnace compartment. But they make bath stoves from two parts of the bath. The second half can go to the construction of a heater or to add a compartment for heating water.

Those who love to make everything with their own hands can build such an unusual sauna stove on their own. For this you need:

1. Pour the foundation for the furnace structure from concrete mortar with or without filler. As a filler, you can use, for example, broken brick.
2. Lay half of the cut bath on the foundation with the curved part up. With a cut, the cast-iron container must be built into the wall with removal to another room, from where the furnace will be fired. On this side, the hole is blocked brick wall and install a furnace and blower door in it.
3. Around the installed half of the bath, at a distance of about 10 cm, red brick walls are also erected, equal in height to the cast-iron container. The resulting space is filled with stones, which, when heated, will heat up, then giving off heat to the steam room.

Furnace construction

A fairly simple sauna stove can be built in two tiers. Heat will accumulate in the upper chamber. The principle of operation is as follows: the gas, passing through the bath, warms up the stones, goes to the opposite side, then goes down and then up, after which it exits the pipe.

Such custom solution, like a sauna stove from an old bath, is not only original, but also quite simple. Its construction does not require the use of any special materials. A self-made furnace design will last as long as a purchased product. In addition, this option requires a significantly lower investment than the purchase of a furnace already in finished form.

Bath stove: video

Do-it-yourself cast-iron bath stove

Old cast-iron bathtubs are made of durable material that can withstand any load and temperature, so not using it a second time for the benefit of your health is big mistake. In addition to its strength, cast iron is also an environmentally friendly material, so during heating, you can be sure that no harmful substances are released in the bath.

How to make an oven with your own hands?

Of course, after using the bathroom, it may not be in the best condition, but all its qualities remain at the same level, for example, it still remains strong and durable, so it is quite possible to give it a second life. Naturally, many who have summer cottages use bathtubs such as a water tank, and those who are great at fantasizing can come up with many other interesting things. If you have a bathhouse in your summer cottage, then you can make a stove out of the bath with your own hands, which will be very expensive in the store. To create a furnace, a material such as cast iron is excellent, because it has such advantages as:

Great durability.

Excellent thermal conductivity.

Withstands even the highest temperatures and high humidity in the room.

It is easy to operate and does not require special care.

Use old bath possible for the construction of such types of cast iron stoves as: outdoor, which will be in the garden, as a fireplace for country house, and, of course, for the bath. Such options can be fully realized with the help of own hands.

Making a stove, how to properly prepare a bath?

It will not be possible to fully use the container, so it will need to be cut. To properly cut, you need to approach this issue with great responsibility. You will have to work with a grinder, you will also need to prepare several discs for metal in advance. Be sure to take care of safety, so put on special glasses, a respirator and gloves. Correctly perform all actions according to the recommendations given below:

1. Before proceeding with sawing, you will need to make calculations and mark up for the future cut.

2. First of all, a layer of enamel is cut, this is done in order to prevent chips along the edges.

3. The cast iron itself is cut into small pieces, while it is worth taking breaks.

4. When half of the bath is sawn, it is necessary to substitute supports under both parts, which will not allow further damage to the tool, and indeed the material itself.

Experts say that cutting is best done at an angle, then the enamel will not exfoliate much.

Rules for making a sauna stove from an old bath

The process of manufacturing a sauna stove is very complicated, because you have to take care not only of quality, but also of safety. The fact is that the stove will be located in the bath building, so there are parameters for installation, for example, it is worth considering the thermal power and its change, the ability to produce steam, as well as the ability to regulate convection flows. As soon as the bath is sawn, you can begin to build a stove in the bath. You will need one half of your cut, but sometimes you can use two parts of the tub.

To properly build such a furnace, you must be guided by the following expert advice:

To make a stove on your own, you first need to prepare the foundation, it is made of concrete mortar, sometimes a filler is used, a broken brick is perfect for this, which can withstand even a large load.

One part of the bath is laid on the foundation, while it is important to make sure that it looks with the curved part up. The cut should be built into the wall with access to another room, where the bath firebox will take place directly. For security and implementation purposes design idea, the hole closes brickwork, then a furnace and blower door is installed.

When half of the bath is properly installed, then at a distance of 10 centimeters, walls of refractory bricks are also erected, which will be equal to the height of the cast iron tank. The space that forms around must be filled with stones, it is they who will warm the room to the desired temperature.

Alternatively, you can build an ordinary sauna stove, which will consist of two tiers, while all the heat will go to the upper tier. The principle of operation of such a furnace is based on the passage of gas through the bath, due to which the stones are heated, and then the heat already flows down and returns up again, after which it exits the pipe.

One cannot but agree that the decision to create a bath stove in this way at your dacha from a bath is creative, but it is also considered rational in terms of extra costs. For construction, it is absolutely not necessary to use any material, except for an old cast-iron bath, you can also make a stove yourself without involving specialists from the outside, of course, this option should be considered if you have at least some experience in building baths. It is important to note that another advantage is the durability of this equipment, because cast iron is a durable material that can withstand high temperatures and moisture, which means that you can enjoy a hot bath for a long time. In addition to saving Money, you also get a durable stove in addition, which is difficult to find in the construction markets, because most of the materials today are not up to quality.

A cast-iron bathtub made back in Soviet times is a durable, solid and very heavy product. However, the once white enamel is losing its former luster, and it is unlikely to be restored. It’s a pity to hand over a bathtub by the weight of scrap metal or drag it to a landfill. What else can be done with it? Some owners of country cottages and summer cottages suggest using this cast-iron product with more useful: make a stove from an old bath with your own hands. Agree, this is original and rational. Such an oven will be able to decorate the estate and make it possible to cook delicious dishes.

Required materials and tools

To independently build a stove from a cast-iron bath, you will need to stock up on the necessary tools.

Here is an exhaustive list of them:

• grinder (angle grinder), as well as discs for it (cleaning and cutting);
• electric drill and a set of drills;
• equipment that allows gas cutting of metal elements (if any);
• spanners different sizes, hammer and pliers;
• crowbar and shovel;
• container where the solution will be mixed;
• spatula and trowel;
• measurement tool: building level, plumb line, tape measure, metal corner;
• a welding machine (it will be needed to mount the chimney), as well as electrodes for it and a protective mask;
• hacksaw for woodworking.

The main element of the furnace is a cast-iron bath. However, the stove has a significant weight, so it must have a foundation. For its construction, a certain amount of sand is needed, cement mortar, bricks, as well as clay and water.

Making a cast iron bath stove is much cheaper and more profitable than buying a new one.

In addition, you will need:

• corner (metal);
• metal sheet (4 mm);
• lattice of a certain size;
• the pipe necessary for the manufacture of the chimney (length - from 2 to 3 m, diameter - from 10 to 12.5 cm, wall thickness - from 3 mm);
• hinges for doors;
• Rabitz;
• polyethylene film (necessary for waterproofing the foundation);
• board (thickness - from 2 to 2.5 cm);
• slats (2 by 2 cm);
• nails.

Making a stove from an old bath with your own hands: step by step instructions

So, let's look at how you can independently make a stove from a cast-iron bath.

For a country house, you can make a stove from an old cast-iron bath, which in terms of strength and service life will not be inferior to models from the factory

First we build the foundation.

1. Using a cord and stakes, we mark the foundation.
2. We dig a trench, the depth of which should not be less than 50 cm. We put layers of sand and gravel on the bottom, after which we carefully tamp them down.
3. On top of the sand and gravel cushion, we put a waterproofing layer, as a rule, which is polyethylene.
4. To raise the base of the foundation, we build a formwork in the center. Usually a common formwork is built, and the pouring is carried out to a height of at least 30 cm.
5. Reinforcement of the free volume is carried out and it is filled with a solution of cement and sand (1 part of cement to 3 parts of sand). You can also fill the volume with brickwork.
6. After pouring the foundation, it must definitely harden.

Now it's time to design the stove itself.

To this end, we perform the following actions:

1. We cut the cast-iron bath across. This must be done carefully, as cast iron is very brittle. If the movements are sloppy, abrupt, you can damage the bath so that it becomes unsuitable for subsequent work.
2. We take half of the cut bath, after which we install it on top, and in such a way that we get a design that looks like a capsule with a cut.
3. Further, a sheet of metal with a thickness of more than 5 mm will be needed for work. For the construction, you will need two halves of the bath and a metal sheet, which is necessary to separate the lower part from the upper (fuel zone from the place where food is cooked).

In the sheet of metal, it is necessary to provide a hole for the chimney, located near the rear wall. The chimney starts from the lower chamber, and then goes through the entire stove.

In order to fix the two halves of the bath and the metal sheet with maximum reliability, it is advisable to use fasteners. To prevent smoke from the chamber located on top, a special sealant, which is called a stove, should be used.

The chimney is attached to a metal sheet using welding.

1. We install the blank of the stove on the bricks. To prevent the structure from falling, it is very important to align it. Before starting to weld, it is recommended to heat the cast iron a little (for example, the material will become much more pliable if the firewood is heated in the chamber).
2. In the lower chamber, we close the front part with a metal sheet, making a large diameter hole in it before that (through this hole, firewood will be thrown into the chamber).
3. We make chamber doors for the furnace and for cooking.

Well, a simple and fairly functional stove is ready. It remains only a little: to decorate the structure decoratively, making it a decoration of the yard. The stove can be painted, for example, in a folk style. No one will even think that a cast-iron bath was used to make the product.

Sauna stove from an old bath

A cast iron bath can be the basis of a good kitchen stove. However, it is quite possible to make an excellent sauna stove from it, and with your own hands.

Cast iron is an environmentally friendly material, so when heated, no harmful substances are released.

Building a bathhouse and equipping a stove in it will require certain skills, so it makes sense to consult a professional before construction.

TO sauna stoves there are certain requirements:

• All such ovens must have enough power (thermal), and they must also have a large range of its adjustment.
• To change the mode of heat and moisture, the device is equipped with a heat accumulator and a steam generator.
• Furnaces should be able to adjust the convention.

So, from a worn-out cast-iron bath, you can make a simple two-tier sauna stove that meets all the requirements listed above. The lower tier of the stove is one half of the bathtub, which faces the wall with a cut, and the convex part upwards. The entire structure must be lined with bricks from the outside. The required steam generation is provided thanks to the stones that cover part of the "bath-furnace". Heat accumulation takes place in the upper chamber.

The principle of operation of the stove is quite simple. When passing through a cast-iron bath, the gas warms up the stones, then reaches the so-called bread chamber located on the opposite side. Then the gas flow makes a “dive” (goes down and immediately up), after which it exits the pipe. A damper is located at the bottom of the furnace to prevent smoke emission.

Cast iron stoves: let's evaluate the benefits

Why is a homemade cast-iron stove (in our case, a cast-iron bath stove) so profitable? Cast iron is one of the best materials for this purpose, however, factory-made cast iron stoves are quite expensive. This material gained popularity due to its strength, although it is fragile. In addition, it is resistant to critically high temperatures and unpretentious in operation.

Modern cast iron stoves are particularly popular

Comparing cast iron and brick stoves, let's say that the thermal conductivity is much better for the first. And since in the bath high temperature support is not constant, the material should not be sensitive to temperature changes.

IN winter time a bath in a summer cottage is usually not heated, because of which the brick sometimes begins to crumble, while cast iron does not know such problems. As for fire safety, only a new brick oven is absolutely not dangerous. In an old product, sparks can break through cracks.

In order to enhance the aesthetics of a do-it-yourself cast-iron bath stove, it is best to brick it. If some blocks are damaged, they can be easily replaced.

Steel competes with cast iron. In terms of heating rate and strength, steel furnaces are not inferior to cast iron ones, but the service life of the former is significantly shorter. Perhaps the main weak point steel furnaces is their susceptibility to corrosion. In cast iron, this problem is not so pronounced.

Having made a stove from a cast-iron bath, you will become the owner of a convenient and reliable device that performs well in all conditions. From such a bath you can also make a very original fireplace for a summer residence. It is especially suitable for those who are now doing the laying of a country house, since the fireplace, as it were, “sinks” into brick wall, and this makes it possible to use the space with maximum benefit.

Video: Universal miracle stove from a cast-iron bath

Having appreciated all the advantages of cast iron (for example, compared to steel) and the relative ease of making a bath from a cast-iron bath, we note that it is very profitable to make a bath from this material on your own. So, if you want to make a stove from an old bath with your own hands, buy the missing material, pick up the tools and get started!