Broke the bath. Dismantling a cast-iron bathtub: two ways to remove an old cast-iron bathtub from an apartment. Getting rid of the bath

In most cases, bathroom renovation is inherently associated with the replacement old bath to a new one or even to - in both cases, you will have to undergo an operation such as dismantling. In principle, it is not difficult to perform, but if you have to deal with, then you don’t have to look for it here - you’ll have to sweat a lot. In this article from the site site we will talk about how to properly and with the least amount of effort to dismantle cast iron bath. Moreover, at your choice, we will offer as many as two ways to solve this problem.

Dismantling a cast-iron bath photo

Dismantling a cast-iron bath: a way to keep the bath intact

In fact, such a dismantling of the bath will require you to tear it from its place, install it in a certain position and simply pull it out of the apartment, while spending a huge amount of effort. You can’t do it alone - at least two pairs of strong male hands. The only way to make the job easier is to avoid intermediate inconclusive actions that usually occur when people do not know what they are doing. The principle "maybe it will pass" only leads to unnecessary labor and loss of strength - you can avoid this if you follow a certain sequence. The question is how to dismantle cast iron bath, is solved in this way.

1. First you need to make sure that the legs are securely fastened to the bath itself - if one of them falls off during the work, then, to put it mildly, troubles can happen in the form of broken toes or hands, and possibly even more serious injuries. In most cases, the legs are fastened with wedges - they must be all in place and tightly clogged (adjust them if necessary).
2. As a rule, almost all cast-iron bathtubs were connected to the sewer, as cast-iron as the bathtub itself - from many years of operation, these cast-iron siphons are so rusty to the bathtub that it is not possible to unscrew them in a normal way. Therefore, we simply take a grinder, put on goggles, lie down on the floor next to the bathroom and cut off the siphon with a grinder.

   

   Dismantling the bath using a grinder photo

3. In most cases, the old cast-iron bath is lined around the perimeter, which also creates some problems when dismantling it - it makes it immovable. This tile, mortar (or what you have smeared around the edges with) should be removed around the entire perimeter - only after that the bath will gain mobility, and it will be possible to continue dismantling the old bath. Further, as they say, a matter of technology.
4. Now the bath should be moved away from the wall. All methods are good here, but the most effective is a crowbar or a mount. If you work together, then you can try to simply pull it away from the wall so much that a person can freely pass there - 400-500mm will be enough.
5. Now we put the bath standing up, for this one will have to climb behind the bath. We take the bath by one of the sides and simply raise it to a standing position - in the process of work it will be possible to intercept the legs. They will play their part and serve as excellent handrails to help you transport the bathtub through the doorway, which is the next step in deciding how to take out the cast-iron bathtub?
6. The technique of transporting the bathtub is very important here - without observing it, it will not work to take out the bathtub. It must be brought into the opening while standing, in an expanded position at 45˚ - as soon as the legs pass behind the doorway, simultaneously with the removal of the bath, it will need to be slowly turned around the door frame. In this way, you will ensure free passage for the other two legs.
7. Everything, the main work is done - the front door to the apartment has a width of 900mm and does not present any obstacles for taking out the bath. The bath can be taken out into the street, loaded into a car and transported to the country, where you will find for it at least a dozen ways to use it, allowing it to extend its life in a different form. For example, an artificial reservoir can be made from it.

   

   How to clean a bath photo

As you can see, the question of how to dismantle a bathtub made of cast iron is easily solved, but even if you know how to perform these works, you still have to sweat a lot.

How to break an old cast iron bath: dismantling with a sledgehammer

This is the easiest way to resolve the issue of how to clean the bath - and with this approach to business, you will have to strain much less. In fact, you just have to break the old cast-iron bath with a sledgehammer - as they say, break - do not build or even dismantle. But, despite this, such a dismantling of the bath should also be done, as they say, with feeling and arrangement, so that God forbid you do not injure yourself. If we represent point by point this method of removing the old cast-iron bath, then the order of work will be as follows.

1. As in the first case, to start such a dismantling old bath must be cut off from the grinder and freed from cement mortar around the perimeter. Also, the bath will need to be slightly moved away from the wall - 10-15 centimeters will be enough.
2. Two cuts with a grinder and a couple of blows with a sledgehammer will allow you to divide the bath into two equal halves. For this to happen, you need to know where and how to make cuts. There is nothing secret here - cuts are made on the curved edges of the bathtub clearly in the middle on its two sides. The wings of the bathtub must be cut through completely - they give the bathtub additional strength. After that, we simply hit the bottom of the bathtub with a sledgehammer, and it kind of folds down.

How to break a cast iron bath photo

In principle, in almost all cases, this is enough to freely take out the old cast-iron bathtub on the street with the efforts of two strong men. But if you decide on your own how to break a cast-iron bath, then to facilitate the task, it is generally better to chop it into pieces, put it in bags and take it to a landfill or scrap metal collection point. For further work, the grinder is no longer needed - the sledgehammer does an excellent job of crushing brittle cast iron into small pieces.

How to dismantle an old cast-iron bath with a grinder, see the video.

How to dismantle an old bath: work safety is paramount

So, we figured out the question of how to cut a cast-iron bath, now it only remains to highlight the topic of work safety. Without this, nowhere - the unorganized work of two people and even simply the wrong use of a grinder or a sledgehammer can lead to serious injuries. So what should you beware of when dismantling a cast-iron bath?

1. Inconsistent work of two people. Each step or movement must be strictly verified and coordinated. Imagine what happens if someone relaxes at the wrong time and the bath crushes the other person? Quite often, in the process of dismantling cast-iron bathtubs, hands are injured. They are either pressed against the wall or dragged between the bathroom and door frame- the last place is the most traumatic, so here you need to be extremely careful.
2. Grinders and sledgehammers, which, as a rule, emit a lot of small particles in the process of work that can damage the eyes and skin of a person. This is especially true when working with a bathroom - its enamel is chipped off in large pieces that can cause serious injury. When doing this work, you need to take care not only to protect your eyes, but also your whole body, for example, wear tight pants and a long-sleeved shirt. Let it be a little hot, but your body will not suffer!

How to dismantle a cast-iron bath with your own hands photo

This is how things stand with the answer to the question of how the cast-iron bath is dismantled. It should be understood that despite the seeming ease of the whole procedure, in fact, this work is complex and difficult. In many ways, it depends on the size of the cast-iron bath - if we talk about a small bath 1.5 m long, then it is easy to handle. But with large products of this type (for example, with a bathtub 1.7 m long), things are much more complicated, and their weight, which goes off scale for 100 kg, is to blame.

In the course of repairing a bathroom in an apartment or when replacing old, worn-out plumbing equipment, it is often necessary to disassemble and dismantle the bathtub on your own - a video of this noisy and dusty stage repair work, and detailed instructions in all steps will help to prepare in advance for possible difficulties and avoid problems. Consider two options - the preservation of the bowl and its complete elimination.

The hardest of all options- dismantling of plumbing made of cast iron. The task is complicated if the plans include taking out the entire bath, so that later it can be used, for example, in the country. The forces of one person are clearly not enough here - a cast-iron product can weigh under 100 kg, so at least two people will have to work.

There is no trace of the bath

Dismantling the problematic old strapping

After removing all objects that interfere with work from the room, the bath must be disconnected from the entire piping, including the drain. Cast iron plumbing has been in many homes since ancient times, when drain communications were made of cast iron pipes. It is usually not possible to simply disassemble them after many years, therefore, it will be necessary to dismantle the cast-iron bathroom with export in other ways.

First you need to disconnect the overflow. If it is made from plastic parts, there are usually no problems. But on old plumbing, you often have to deal with metal components that are not easy to dismantle. Sometimes you can unscrew this element with the help of pliers, simply by hooking the grate with them and turning it counterclockwise. If the overflow grate is strongly boiled, then you will have to use a grinder:

1. Make a deep cut on the overflow with a grinder.
2. Using the cuts, knock down the overflow grate piece by piece with a chisel.

Incision of the grate and dismantling of the overflow

With plastic elements, problems usually arise much less. It is only necessary to unscrew the fastener on the grate (bolt or nut), after which the overflow can be freely and without effort detached from the bath. The situation is similar with the drain - the siphon is easily disconnected after unscrewing the nut on the metal protective grill.

How to disconnect a cast iron siphon from a bath

To dismantle the bath, you need to disconnect the drain from it. If the drain is made of cast iron, then difficulties may arise at this stage. There are several ways to disconnect a cast iron siphon from plumbing. The first one is similar to that described above - an incision is also made on the top of the drain by a grinder, but already crosswise. The main thing here is to saw through only the drain grate without damaging the bath itself.

Cuts in the drain guard

If the grinder accidentally saws through the cast iron of the bath, then in the future it is no longer possible to put a new harness on it. Of course, if the surface layer of enamel is only slightly touched, nothing terrible will happen, but if a deep cut is made by negligence, plumbing with a new strapping will definitely leak. Next, you need to act in the same way as in the case of overflow:

1. On one of the resulting cuts, place a chisel at an angle of about 45 degrees so that hitting the tool rotates the drain grate counterclockwise.
2. In this way, try to unscrew the drain. If this is not possible, deepen the cuts if possible and simply knock off the ribs of the grate. To do this, the chisel must be placed so that the blows are no longer directed counterclockwise, but inward - towards the center of the drain.

With a chisel, you can also knock out the cross at the bottom of the grate. This will make it easier to get rid of the remaining parts after cutting. Upon completion of the dismantling of this element, the siphon will hang freely in the opposite section, being connected to sewer communications. To remove it, you only need to break the coupling in this place.

An effective way to dismantle the old strapping

Dismantling the harness before removal

Another way to remove the siphon to dismantle the bath involves using a perforator. The desired element is attached under the bathtub with a large cast-iron nut, which is simply not possible to unscrew in the usual way after many years of operation. But if you use a perforator, then the task is simplified:

1. The tool must be switched to shock mode and a flat chisel nozzle must be fixed in the cartridge.
2. Loosen the large nut connecting the siphon with the drain, acting on the edges of the nut with a perforator in shock mode, so that it gradually unscrews, that is, counterclockwise. After that, it will be possible to dismantle the siphon by hand.

There is nothing complicated in this method, in addition, there is no need to use a grinder, which can easily damage the enamel or even accidentally make a deep cut, rendering the bowl unusable.

After disconnecting the siphon from the bath, cut or break the unnecessary section of the drain pipe using one of the methods described above.

Video: Dismantling in the bathroom without damaging the plumbing

Dismantling of the old cast-iron pipes remaining on the sewer bed

After breaking the drain, it will be possible to remove the cast-iron piping under the bathtub. So that the dismantling of the bathtub is not difficult, it is recommended to saw off the siphon from the sewer system with the same grinder. True, you will have to work in a respirator, since when working with a grinder, cast iron produces very harmful fine dust, which cannot be breathed without protective equipment.

Dismantling the old cast iron bed

As alternative the pipe can simply be knocked down, since all elements are easily pricked. To do this, you can use an ordinary hammer, which you need to hit on the protruding parts - the tee, connecting elements and other parts. After that, the pipes usually loosen and are not difficult to remove without any plumbing tools.

Fast and safe removal of plumbing

After removing the old trim using the methods described above, you can begin to work on dismantling the cast-iron bath. To take it out, you need, if possible, to get rid of all interfering objects - the toilet bowl, if the bathroom is combined, washing machines, all kinds of shelves, bedside tables. The sequence of work is as follows:

1. Remove the plaster from the end and side walls adjacent to the bath.
2. Turn the plumbing on its side. It is easy to separate it from the wall, just lift and lower it several times.
3. Disconnect the legs. In older models, for this, simply knock out the wedges from the mounts with a hammer.

After freeing from the legs and communications, the bath is simply taken out of the room. If possible, remove the door from the hinges - so it will not interfere with dismantling, and it will be impossible to accidentally scratch it. Also do not forget to plug the sewer socket with some rag material. Otherwise, the room will quickly fill with unpleasant odors.

Scrapping of a cast-iron bath for removal in parts

If you want to dismantle the old bath and install a new one, then the simplest and most fast way get rid of outdated plumbing - just break it with a sledgehammer. Cast iron is a metal, although durable, but it is not able to endure a series of strong blows with a heavy hammer and will definitely crack. After that, even small pieces will not be difficult to take out of the apartment even for one person.

The only significant drawback of this method is the strongest noise emitted during the scrapping process. To knock had less, you can use a grinder. The procedure will be as follows:

1. As in the previous case, disconnect the plumbing from the communications, cut off or otherwise dismantle the drain pipe.
2. On the perimeter, free the bath from the cement mortar. If there is a decorative screen, then it breaks with a chisel and a hammer.
3. Move the bowl slightly away from the edge of the wall. With a grinder, make cuts on the folded edges in the middle on both sides. It is these edges that give the bowl the necessary rigidity, so you need to saw through them completely.

Then it remains to hit the bottom with a sledgehammer a couple of times, after which the bath will “fold” exactly in the middle. The only thing that should not be forgotten throughout the work on the demolition of sanitary equipment is eye protection. Use special masks or goggles, otherwise broken pieces of enamel or chips can lead to injury.

Video: How to break a cast iron bath

The work of disassembling communications, demolishing and removing the old bath is not extremely difficult, although its laboriousness for one person is very significant. The biggest difficulty is the dismantling of the cast-iron drain, the stuck nut of which is almost impossible to unscrew without the help of, for example, a perforator. Breaking will also require significant physical effort, so it is better to do the work with an assistant or immediately seek help from a specialist.

Video: The complete elimination of the plumbing system by the grinder

Albert Yasaulov
How to split a cast-iron bath into pieces? Why break? Make cuts with a grinder - and with a sledgehammer. Autogenous. Cutting is not destiny? With a sledgehammer - punch a hole in one place and it will go to crumble like there is nothing to do, just hit with sharp blows, and take a sledgehammer with a short handle - God forbid you disperse and smash everything in the apartment. A friend of mine did just that, beat and beat with a sledgehammer and smashed it, then took it piece by piece to the trash heap. True, he lives on the first floor, and if you are taller, then I don’t think that the lower neighbors will be very happy.

Lyubov Opalikhina
Is it possible to cut an old bathtub with a grinder? it's just not realistic to take it out. Make cuts and break it with a sledgehammer. It should turn out better than mine - I just smashed it with a sledgehammer, but it’s hard and very noisy. certain places) and broke into three pieces. Cut with a grinder and crap with a sledgehammer along the cut. It will break only on the way. If you find a problem, call a couple of homeless people - they will endure it. And they will drag it to the metal collection point. I had this from the garbage dump, the bath was immediately dragged away

Viktor Samokhvalov
How to break a cast-iron bath They are taken whole. They will come straight home and pick you up. At least that's how it works in our city. Even ads are up. Cast iron is not hard to break. Take it to the street and beat. Cast iron is prickly. Bulgarian cut. Sledgehammer.

Valentina Lisina
How to get a cast-iron bathroom out of the apartment (5th floor, no elevator)? Two bums and a bottle of vodka You can smash a sledgehammer into a window or from a balcony We carried it out together. Also cast-iron (more than 100 kg)

Vitaly Negushin
What's better? Buy a new bath or cover the old one with a special coating? There is money - buy a bath! We made an acrylic insert - for more than 5 years the bath looks like new, the pleasure cost 5500 rubles. , the master spent 2 hours. if the old bath is not split into pieces, I see no reason to spend money on a new one. It seems to me that it is better to put a new cast-iron shower stall. Steel and acrylic for nothing.

Vadim Okunev
How to take out a cast-iron bath? Can it be broken? If it’s cast iron, then you can break it into pieces with a hammer and hand it over to metaplom, it’s expensive now! Throw out the window. I called the Tajiks who work as janitors, they dragged away like ants, you won’t find it. It won’t break. And not alone. You can call industrial climbers, and through the window. It is unlikely to split, to cut. It’s easier to throw it out the window, it will split itself)

Denis Veshnyakov
How to break a cast iron bath? Kettlebell 32 kg. Another CAST IRON BATH! aaaaaaa NIGHTMARE

Albert Gladkikh
Which bath do you recommend? personal experience(cast iron, steel, acrylic What material is more convenient to use? Thank you! There are no comrades for taste and color, but in any case, not steel about acrylic - they say, it is not durable, it scratches, some special detergents, etc. - complete nonsense. acrylic bath 3 years. Excellent thing. Simple installation, because it is easy .... The most excellent is steel, because cast iron is brittle like acrylic, and steel was straightened with a hammer, painted and everything is ok.

Alexander Dryablov
A plastic sewer pipe was connected to some kind of cast-iron solution - how to fix a leak there? It happens often. Don't be self-employed. Call a locksmith from the Housing Office, pay him the money, he will do everything. It will become cheaper. Dig out this solution and buy a special rubber cuff. Insert a 70-40 mm rubber cuff into the cast-iron socket. In this cuff 50 mm plastic pipe with difficulty, but enters. This is the most reliable. If it does not work out, put a cuff of 70-50 mm.

Valeria Kondratieva
Hello) Faience sink in the kitchen, how is it? seems to have done something stupid = (? / + No, before there were cast-iron sinks with a coating like those of bathtubs and steel enameled ones. Cast-iron ones washed well and served for 20 years), steel-enamel was chipped off just like from enamel. pots and teapots And faience is the same type as the sink in the bathroom ... Refuse of course. Previously, when there were no stainless steel sinks, we had such first 5 years to clean well, but then.

Lilia Glebovskaya

What happens if the hair dryer falls into the water? Let's calculate) the hair dryer is an electrical appliance 220-240V 1200-1800 W (heater) The motor itself is 150 W. Further, if you fall in the bathroom, you can break your head and even die if a strong blow is not indicated how they will slip ... If the bath is cast iron and grounded, then an electric shock is not excluded, because there will be a phase on the hair dryer. And so, the short circuit will be through the wire located before the heater, since the electrical conductivity of water is very high.

Olesya Ozerkova
Mystery! My bathtub is 70 cm wide, and the passage of the bathtub is 55 cm. Question: How did it get there and how to remove it from there? 60 cm high bath can not be. She has a standard height on legs of only 56-58 cm. They brought her sideways. I have a passage of 60. and a corner bath 105 by 150. I calmly entered. The depth of most baths is standard about 45 cm without legs. except for the iron ones, of course. When dragging a cast-iron instead of a song, indecent sounds ...

Victor Lebedev
Of course, I’m not a plumber, but it’s a pity for money for an uncle from the side: HOW TO REPLACE A SEWER PIPE IN THE BATH WITHOUT PROBLEMS? Ho-ho! And do not think without problems! I am a plumber and I can say one thing: not moving the bath away is sooooo dreary and difficult. With all the tools and experience, I did this work alone for two days. But if you decide, remember: the most ... The whole difficulty is to throw out the old pipe so as not to break the common riser. If you succeed, then collect the plastic. A pipe is simpler than a steamed turnip P.s. If you do it yourself, do not forget about the slope of a few degrees from ...

As a rule, repair work in the bathroom is inextricably linked with updating the plumbing equipment, in particular, replacing the bathtub with a newer model or shower box. One way or another, the old plumbing equipment will require dismantling. Usually this process does not cause any particular problems, but if a cast iron bath is installed in the room, you will face some difficulties.

Usually, Replacing a bathroom with the installation of new equipment can be fraught with all sorts of problems. The sequence of actions in the event that you need to leave the old container intact will be such that you will have to remove the plumbing fixture from its installation site and transport the container from the apartment to the street with difficulty. This is a rather laborious process. Here it will be useful to attract several helpers.

Only two people can take the cast-iron bath out of the room

When carrying out such work, it is necessary to adhere to a certain algorithm. The dismantling sequence has some features that make it possible to facilitate the technical process as much as possible. You can optimize the dismantling of a cast-iron bath as follows.

First of all, you should carefully check the quality factor of the brackets that fix the bath in its original position. If one of the supports is knocked out during dismantling, there is a possibility of injury. Therefore, you should protect yourself in advance.

If during the installation of the structure you wedged the legs of the tank, make sure that all elements are in place and securely hold the tank. Loose wedges can simply be knocked out with a hammer.

Previously, the bath was connected to waste system through a cast iron siphon. Due to the action of such a factor as corrosion, the articulation of the parts of the drain system is compacted to such an extent that it becomes unrealistic to disassemble the piping while maintaining the integrity of the elements. In this case, you should separate the part by cutting it with an electric cutting machine. At the same time, do not forget to follow safety precautions and use safety glasses. To cut off the flange connecting the drain trim, you will need to lie down.

Sometimes you can disconnect the bathtub from cast-iron communications only by cutting the pipe with a grinder

Another common problem is that today, in most cases, the walls of the bathroom are lined with tiles. This will create some inconvenience in the event that it is planned to dismantle the old bath. The tile should be removed along with a layer of hardened adhesive construction mixture around the perimeter of the product. This is necessary so that the old container can be pulled out. At the current stage, the dismantling of the bathroom can be considered completed.

A method for replacing a cast iron product in which the container remains intact

Starting work on removing the tank, first of all, the plumbing fixture should be pushed forward. The most convenient way to do this is with a lever, for which it is advisable to use a crowbar or mount. Provided that two people are involved in the work, it would be most correct to move the bath from the wall by about half a meter, that is, so much that one of them could easily fit there.

You need to take the bath out of the room on its side

After that, lay the container on its side. To do this, it is necessary that one of the workers is between the wall and the side of the product. Now the product must be taken out of the bathroom. Here it is appropriate to use the bath supports as handrails. By holding them, you can conveniently transport the cast-iron container.

At the current stage, you should follow some rules. If you neglect these recommendations, you will not be able to take out the plumbing fixture. You need to move the product into the doorway on the edge and, given the turn, first remove the front legs. Further, gradually turning the container, take it out of the bathroom in such a way as to be able to hold the second pair of brackets.

Now it remains to take the product out of the housing. Because the canvas size front door, as a rule, not less than 800 mm, this will not cause any particular difficulties. How to deal with the old tank is up to you. Maybe you decide to take him to Vacation home, where the capacity can be used by at least a dozen different ways allowing the old plumbing fixture to perform a useful function. In particular, an old cast-iron bath can serve as the basis for a decorative pond.

Dismantling a cast iron bath with a hammer

If you decide to rent a cast-iron bath junk, we can recommend using this in a simple way removing an old product from a bathroom, like destroying a bath body with a sledgehammer. This is the lightest and rational option dismantling. In order to reduce the likelihood of injury, it is necessary to adhere to a certain sequence of actions. Work should be carried out in this order.

First you need to cut the sides of the bath in half with a grinder

First of all, it is necessary to cut off the connection of the bath to the sewer with a grinder and free the sides of the plumbing fixture from the layer of tiled mortar and the remnants of the cladding around the entire perimeter. The tank should be moved from the wall by about 10–15 cm.

In order to easily split the body of the bathtub into two parts with a sledgehammer, it is necessary to apply files with a cutting machine on certain areas of the surface. Cuts must be made on the rounded part of the container strictly in the middle of the product on both sides.

The sides of the bathtub must be cut through completely, since in this case they serve as a supporting element in the structure. Now one good blow with a hammer on the bottom of the tank will be enough in order to divide it into two equal parts. In this case, the bath, as it were, will fold down.

With a heavy hammer, you can break the remains of the bath into small fragments so that you can take them out in bags alone

The fulfillment of these conditions will be enough to facilitate the dismantling of the bath. Two workers can take parts of the old product out of the room, although this can be done alone. To do this, it is advisable to split the parts into small fragments, collect them in strong bags and take the bath to the place where scrap metal is received or to a landfill. In order to break parts of the bathroom body, cuts with a grinder do not need to be made. Cast iron is a rather fragile material, and the remaining parts of the structure can be easily broken into small pieces with a sledgehammer.

Safety precautions when dismantling the bath

In the course of work, injury-prone situations may occur. This may be caused by inconsistency in the actions of two people, non-compliance with the rules for working with a cutting machine or hammer. Most often, injuries occur in several typical cases. Let's consider them in more detail.

If the bath shoes are tiled, remove the container from the fixtures and lower it to the floor

The likelihood of injury may arise due to uncoordinated actions of workers. It is very important to precisely coordinate each action. In the event that one of the assistants accidentally releases the bath, the second person will not be able to hold the product on his own and will be pinned down with a cast-iron container. Most often, during the dismantling process, the hands suffer. The limb can be pressed against the wall or stretched between the body of the product and the frame of the doorway. At this point, special vigilance should be exercised, as this is one of the common causes of injuries.

Care must be taken when lifting the edge of the tank. The bathtub can slip on the slippery surface of the tile, and one person cannot hold it. In order to avoid this, it is necessary to lay a non-slip gasket under the side of the sanitary container. It could be a rubber mat.

In the case when the edges of the product are firmly embedded in the wall, the dismantling procedure is somewhat complicated, and there may be additional sources injury. It is rather problematic to beat off a layer of old tiles and cement mortar from the sides of the plumbing fixture so that the product can be freely pulled out. In this case, you can make the task easier by knocking out the supports of the structure in turn. After that, you need to apply force so that the container falls to the floor. Before detaching the racks of the structure, it is necessary to put a layer of shock-absorbing material under the bathtub on the floor to compensate for the force of impact when the tank falls.

In the process of working with tools such as an electric grinder and a hammer, a lot of small pieces of scale, metal chips or fragments are inevitably scattered, which can cause serious injury if they come into contact with the skin or eyes.

Special care must be taken when breaking the body of a sanitary ware into small fragments. In this case, the enamel coating of the bath breaks off in large pieces, which, flying off, can cause serious injuries. During the work, not only the organs of vision, but also all parts of the body should be protected from damage. To do this, you can wear work pants made of dense material and a jacket or a thick shirt with long sleeves. Of course, in such clothes you can become covered with profuse perspiration, but in any case it is preferable to get injured.

Do not neglect eye and hand protection, because this will help to avoid accidental injuries.

Increased injuries during dismantling activities can be avoided by following the necessary safety requirements.

Getting rid of the bath

To free the room from the details of the plumbing structure, you will need the help of several strong men. In addition, this requires transport. The services of loaders and cargo taxis can be quite expensive. Today there are companies that export bathtubs. You don’t need to do anything yourself, just call a team, and the specialists will quickly and efficiently dismantle. You do not have to pay for this - the company pays for its costs and makes a profit by selling scrap metal. In addition, the old bath can serve for a long time if the damaged layer of enamel coating is restored.

To get rid of an old bath, you can contact a company that disposes of such plumbing.

The need to cut the cast-iron structure arises when dismantling communications. You will learn about how to cut cast iron and structures from it from the material.

Most often, the need to cut the cast-iron structure arises when dismantling outdated communications. Hope for a speedy completion of the work collapses immediately - in the Soviet Union, pipes were connected with cement, sulfur and aluminum, so it is incredibly difficult to cut them. But a couple of working methods are known. You will learn about how to cut cast iron and structures from it from the material below.

As with any metal, cast iron cutting methods are divided into thermal and mechanical. The choice of a particular tool depends on the design features. The following is the equipment that saws (or cuts) cast iron:

• pipe cutter;
• angle grinder;
• chisel;
• hacksaw for metal;
• jigsaw
• plasma installation;
• gas cutters.

Now it is worth evaluating cutting with the help of these tools with cast iron objects.

pipe cutter

This is a special device for cutting pipes from different materials. There are manual (mechanical) and electric tools. Both types are suitable for diameters 15-360 mm.

First, a carbide disc is mounted on the apparatus. The removable element has a number of advantages over classic abrasive ones. For example, 4 times faster cutting speed, no sparks and no need to add any substances to the cutting zone. A diamond coating is applied over the cutting edge, which prolongs the service life of the products. Examples of pipe cutters for cast iron pipes are portable Exact Pipecut products for diameters less than 360 mm.

Alas, rarely a home pipeline can be easily cut with a pipe cutter. It may be difficult to access the tool or the cutting point is bent so that the device cannot be captured. Therefore, it is worth considering other options.

Angle grinder

Working with a grinder is quick and convenient, but not without drawbacks. For example, it cuts only in a straight line. An attempt to make a figured cut will lead to “biting” of the disk, its breakage, and possible injury to the user. Therefore, the machine is used for cutting in a straight line. Another disadvantage is the fire hazard of the method (abrasive disc + metal = sparking). Before work, you will have to wear goggles, face protection and hands.

Cutting around is more efficient than with a jigsaw, so more often users choose a noisy grinder. When buying a cutting wheel, prefer products on a bakelite bond, because they are an order of magnitude stronger than their ceramic counterparts.

Hacksaw for metal

A device similar to a grinder by the principle of operation. You will have to mess with it for more than one hour, especially if you cut a large-diameter cast-iron pipe. The disadvantages of the method are time costs, physical effort, the inability to work in a limited area. But the method is safe.

Working with a chisel and hammer

This pair of products will help separate the cast iron into hard to reach place. Dismantling work begins with pipes remote from the riser in places where a grinder or a hacksaw cannot be inserted. Since cast iron is a brittle material, it is easily destroyed after point dynamic loads.

A good percussion instrument has a rubber or polymer tip to soften the impact slightly. This is necessary so that the pieces of cast iron do not scatter around, do not fall into the riser and do not create a blockage.

A chisel and hammer work great with Soviet-era cast iron, that is, combined with sulfur, aluminum and cement. As you move to the riser, there is usually more free space for work, so further cast iron can be cut off more effective device. As with a grinder, when working with a chisel, it is recommended to cover areas of the body into which a cast-iron fragment can fly off.

The productivity of work is extremely small, but sometimes you can’t do without them.

Electric hacksaw

It is much more convenient for the user to work with an electric saw than with a grinder, although the principle of operation is not much different. A lightweight device with smaller dimensions than an angle grinder, the web is consumed more slowly than the disk, if it is correctly selected (marking HSS or BIM, and the length is also taken into account).

Less trauma, the speed of the process is something between a grinder and a manual hacksaw, the cheapness of consumables and their availability are the advantages of cutting cast iron with an electric hacksaw.

Plasma cutting

The method relates more to industrial than to household, so it will not be considered in detail. If the goal is the minimum consumption of material, speed of work, noiselessness, the best equipment not for cutting cast iron. The plasma will make cuts in workpieces with a thickness of more than 200 mm, and the sawn material will hardly have to be processed at the end of the work.

The method is used by large enterprises of metallurgy, industry, where there is a need for cutting and transporting scrap iron. Plasma installations are indispensable for volumetric work.

gas cutting

There are two methods of gas cutting of cast iron:

• gas-oxygen;
• oxygen spear.

In the first case, the workpiece is affected by the thinnest jet of flame supplied under high pressure. The product of combustion is usually a mixture of oxygen with kerosene or diesel fuel. By the way, effective method during the elimination of man-made accidents.

The second method resembles oxy-fuel, only a thin tube of hardened steel acts as a cutting element. Its tip is heated to almost 1500 degrees (welding / soldering iron / lamp), then oxygen is supplied through it, ignited at the outlet and heated to 2000 degrees. The resulting burning mixture easily copes with thick cast iron.

Both methods are good, but there are disadvantages - it is important to have experience with gas equipment. Responsible and precise cutting should only be done by a professional. The second drawback is the release of gas that is harmful to health during the operation of the torch.

The method is suitable for outdoor work or in the garage. For example, the need to eliminate a cast-iron castle with swing gate. The cutter works quietly, you will not disturb anyone.

Conclusion

Based on the opinion of experienced builders and repairers, in the best possible way cast iron cutting stand out:

• for home - grinder, hacksaw;
• in the garage - gas cutter;
• in production - plasma installations.

Experienced people advise taking several tools into service when working at home, starting with a chisel and ending with a jigsaw.

Do you know how to quickly saw off a cast-iron lock or pipe? Share your experience with readers in the comments.