Pocket pond or how to make a pond from a tire with your own hands. How to make a lake or a pond out of old tires in the country How to make a pond out of a wheel

Often, the owners of cottages or plots want to decorate their possessions by making ponds with their own hands from a tire. Such a pond made of tires undoubtedly becomes a good source of coolness and pleases the owner himself, as well as his guests, and is an adornment of everything. suburban area. Only the sight of a pond and its water surface is enough for a person to relax and feel like a real vacation. However, some, judging that their own site is not so big, do not move beyond just a dream. And in vain! This article will show you step by step how to make a pond in the country with your own hands from tires or tires.

Place for your mini-pond: how to find it

It should be located where it will attract our attention, so you need to choose it very carefully. It is important to follow a few rules that will help make your choice successful:

1. Your pond doesn't have to be constantly in the sun. The best place for the location of the reservoir - partial shade. If this factor is neglected, then the plants will wither, and the water will bloom.
2. The space open to the winds is also not suitable.
3. A pond surrounded by trees will quickly fill with fallen leaves and wood dust. Such a pond will need to be cleaned frequently, which will require a lot of time and effort.

It would be great if the reservoir is located in a place overlooked from everywhere. Then the whole surrounding landscape will be well reflected in it. When such small reservoirs are in a lowland, they look much more attractive. Therefore, when looking for a place for a pond, then try to find such a natural recess in the area. Eat good way find such a site without spending much effort.

The picture shows a place where your pond will not be under the constant rays of the sun, and also which is visible well from different sides.

Previously, you can simulate the location of the future pond by placing a piece of plastic wrap in the place you have chosen. Now go around it to see how the future mini-reservoir will supposedly look from different sides. If you like it, then this is the right place.

Where to find the right tire

Before looking for the right tire, you need to consider what size pond you need and how deep. If there is not enough space for a large structure in the summer cottage, then just one slope from the car will be enough for this. And if the plot of land is large, then for the implementation of this project you need larger tires, with a diameter even higher than a person's height. For example:

1. Slopes from a KamAZ car;
2. Tractor wheel "Belarus";
3. Tires from BelAZ.

What to do when there is no suitable tire? The right one can be found at a service station, where there is a lot of rubber, which will still have to be disposed of. You can look for used tires at any car depot or ask a neighbor who has a car. Sometimes used tires just lie on the side of the road.

Large slopes from Gulliver, Kamaz, BelAZ are not easy to find. Often they are not suitable for our relatively small areas.

What will your pond look like?

Would you like to have fish in your lake? In a small lake, this is hardly possible. But if you have a pond from a large tire, then you can start, for example, goldfish. But in another case, if the structure was not made for fish, then it can be decorated with various plants, pebbles, animal imitations and other artificial decorations. In general, it all depends on your taste and imagination.

So that no one guesses how your mini-pond appeared, you need to close the rubber base well with a stone. You can also add lighting from lamps to the decoration. During the day they collect the energy of the sun, and at night they reflect beautifully from the pond.

Mini pool for children (video)

However, one should not forget that any mini-pond may be unsafe for small children who are left alone near the pond without adults.

The decoration of the pond has two sides. When decorating a pond, we think about the aesthetic appearance. But you need to remember that kids can also become connoisseurs of beauty, who are also attracted by decor and various figures. Children should not be left near water without adult supervision.

Now for the step by step tutorial.

The success of any undertaking depends on good preparation. Must be pre-assembled the right materials and tools - this will help you once again not be distracted during the main work.

Step one - collect inventory, procure materials

Inventory: shovel and large sapper shovels, building level, electric jigsaw or hacksaw.

Materials: car tires, polyethylene or special waterproofing material for pools, sand, gravel, large stones for decorating the edges of the pool, plants for landscaping.

When everything you need is collected, proceed to the second step.

Step two - preparing the tire

We first remove dirt from the tire. After that, you need to cut off the top of the slope.

On the tire, you need to cut off the upper part

Step three - dig a hole for the pond

To start digging a hole, you need to level the surface that we have outlined for the reservoir. Also, before starting work, you need to set the depth of the future lake, according to the rubber base, as well as the desired look.

Dig a hole

The rubber base of the reservoir can be:

1. Lower to the depth of the entire tread.
2. Dig in half
3. Leave most of it on the surface of your site.

We dig a hole. We make a shape that corresponds to the outer diameter of the tire, with small indents around the entire circumference for free lowering it to the required depth.

If you do not bury the tire completely in the ground, then the remaining side will protect your pond from sewage.

The pit needs to be dug, taking into account the necessary "cushion" of sand (about 15 cm). We pre-align the bottom so that the waterproofing gasket is not damaged. If necessary, the sand must be sifted to remove hard lumps and small pebbles in advance. The bottom is important to carefully tamp and align horizontally.

Construction stages

Step four - waterproofing device

You can use ordinary polyethylene, but keep in mind that it is short-lived. After a short use, it deteriorates from exposure to the sun, water and temperature changes. It is better to take waterproofing for the construction of stationary pools, which is much more practical. It is sold in specialized stores or in hardware stores. Of course, when using special waterproofing the cost of your pond will be higher, but the water from it will not flow into the soil. I do not want it to be like in the saying: "the miser pays twice."

Instead of a film, it is better to take waterproofing material

How much material is needed? As much as necessary so that the canvas covers the bottom of the tire, fits against the walls, and so that there is another half a meter of film outside the edges of the pool. In order for the waterproofing material to fit snugly to the bottom and walls, it is best to fill the entire container with water when laying. She will push everything internal surfaces reservoir and give them the correct shape. Try to straighten the waterproofing material well. To keep it in the right position, press down on the edges with large rolled stones.

Decorating a pond with stones

Step five - install the walls and bring beauty to the pond

We level the edges of the waterproofing material and sprinkle with sand and screenings. Now the membrane is fixed completely and will not move out. Sand will be the main material for the design of the future reservoir.

Designer's tips for installing a tire pond (video)

How you want to use your reservoir will depend on the versions of the distribution of stones.

For swimming and bathing

In order for your project to build for swimming, the tire must be quite large. Do not overload the banks of this structure with large stones, otherwise bathers may suffer. A great option would be to simply form a platform along the walls.

For decorative purposes

In another case, if the pond is only for design purposes, then you will have to fantasize about the distribution of stones and plants and decor, thereby emphasizing the look of your yard and making others happy with it. Now don't worry about the jagged rocks, it will look very impressive.

Decorative pond with fountain

It is advisable to lay the stones in rows: large and rounded stones - from below, and small stones - from above. Miniature, smoothed sea ​​water pebbles will help beautifully cover the bottom of the mini-pond. Sand with gravel is not recommended as a bottom decoration due to the fact that the water becomes cloudy and unpleasant in appearance.

Small or medium-sized animals live in every yard. For example: hedgehogs, moles or mice. If you do not want to see them dead in your reservoir, then take the time and effort to find a snag that will give originality to your reservoir, well, and if you're lucky, it will save the life of some small animal.

Conclusion

Decorating your yard or garden with such an original structure is very simple and does not require large cash outlays. All you need is a little time and energy and imagination. The work itself will bring you satisfaction, and the result will bring joy to you and your loved ones.

Tire jacuzzi (video)

If you decide to buy an artificial pond for giving, do not rush to spend money! It will be much cheaper to build a pond in the country from a tractor tire. As you know, the wheels of these machines are large, and, accordingly, the diameter of such a pond will also not be small.

To prevent water from passing through the wheel, you can use pvc film but it has many disadvantages. It is more reliable to concrete the bottom of our future reservoir. Concrete is not brittle, will not tear and is not afraid of temperature changes.

So to create artificial pond at the cottage with your own hands you will need:

• 2 shovels (bayonet to dig a hole under the wheel and shovels to remove excess soil);
• building level;
• saw (it is better to take a grinder with a regular circle for metal, but if it is not there, a hacksaw will do);
• gravel sand and stones;
• plants for pond decoration.

How to make a pond from a tire?

Introducing step by step guide construction of a pond in the country:

• The tire needs to be prepared: cleaned of dirt and dust, remove the upper part (cheek) with a grinder or a hacksaw.
• Decide on the place where the reservoir will be located.
• Determine how much to deepen the base. Is it possible to place a pond on the surface of a flat area, on? or dig into the ground for the entire width of the treads.
• Dig a hole according to the shape of the future reservoir, but slightly larger than the diameter. Level the bottom and pour a sand cushion (at least 15 cm). Tamp and lay the tire on the bottom of the pit.
• For sealing, you can choose one of several options: use a covering material for pools - spread along the bottom of the pit and bring the edges 0.5 m beyond the laid tire or concrete the bottom of the tire.
• If you used the first option - in order to evenly distribute the film in the tire, you need to fill in water. To fix the material well, as an option, you can lay stones around the perimeter of the pond.
• Now, before completing the construction of the pond in the country, you can place a fountain in it, for which you need an electric pump or an aquarium turbine with a nozzle. To protect yourself and others from electric shock, the wire should be pulled through the hose and slightly covered with earth.

As an additional decor, you can install lighting from garden lamps on solar panels. So you can create an artificial pond in the country with your own hands with minimal cost. In addition to an artificial pond, tires can be used to make an excellent barrel for water. For more information on how to do this, read the following article.

Old tires are not just obsolete rubber.

This is a valuable high-quality secondary raw material. Reliable, strong and durable.

You can get tires free or very cheap.

Tires can be used to create many useful things.

Of these, you can create a small reservoir of tires with your own hands for a summer cottage or garden, namely:

• decorative pond;
• pool;
• fountain.

Let's figure out what is needed to create such reservoirs.

To create a small decorative pond, it is quite enough passenger car tires.

Tools

In our work we will use:

• two shovels (bayonet and shovel), as well as crushed stone and sand;
• building level and jigsaw;
• waterproofing material to cover the bottom; the best option— special cover for swimming pools;
• small boulders to beautifully decorate the banks of the pond;
• plants for ornamental ponds.

If you want to create not just a decorative pond, but a real swimming pool, you cannot do without large KAMAZ or BELAZ tires.

Operating procedure

First, remove the top of the tires. Best Tool for cutting - electric jigsaw. It should work at low speeds.

An alternative but less effective tool is hacksaw for metal. It will take an order of magnitude longer to remove the tire top.

Now create a recess for the pond:

• first of all, we level the territory for the future reservoir;
• then we dig a recess for the tires to create the base of the pond; around the circumference leave small space for allowance - they should not sit tightly in the recess of the tire;
• put tires; using the level, we check how horizontally exactly relative to one another they are all stacked.

Pond it is better not to build in the sun, otherwise the plants in it will wither, and duckweed will cover the water.

In the shadow large trees building a pond is also not worth it - clog up quickly twigs and leaves.

The ideal place for him is partial shade.

To prevent the pond from leaking, you will need special materials that cover the bottom of the pools. As a cheap and not very reliable alternative suitable pvc film.

The shelter should completely cover the tires and extend approximately 0.5 meters beyond their edges.

We carefully spread the bottom cover and fasten it to prevent it from slipping. For this you need to press down the edges with boulders or cover with rubble.

• sprinkle the edges of the shelter with a small amount of sand;
• around the edges of the recesses we put boulders and pebbles - we create “shores”.

Stones are best laid out like this - place large boulders below, smaller ones on top.

The “membrane” itself can also be slightly decorated with small rounded pebbles so that it does not catch the eye.

Gravel and sand are not used for decoration. They make the water very cloudy.

And finally, we plant plants and pour water. The pond is ready.

Fountain

A fountain made of tires in the country is a wonderful element of decor that will add coziness and surprise guests. Making it yourself is not at all difficult.

Tools

To make a fountain, you will need the following tools and materials:

• large tire (from a truck or tractor);
• shovel, cement mixture(in a dry finished form), as well as a container for its cultivation;
• a mixture of sand and gravel;
• mastic for waterproofing and a pump for pumping water;
• reinforcement in the form of rods, a thin iron sheet and metal posts;
• scissors for cutting metal.

It's good if you have more on hand. building level- the product will come out more accurate and verified.

Procedure

The fountain is created like this:

1. First, we pull out a shallow funnel-shaped pit, whose size should be slightly wider than the diameter of the tire.
2. We fill the bottom of the pit with a pillow from the mixture sand and gravel.
3. On the pillow we pour cement- the future basis for the foundation. Its height should be approximately 10-12 cm. How horizontally even the base is, we check using the building level.
4. When the base has a good grip and dries to the bottom of the pit, we begin to “hoist” a tire on it. But first, on one side, we slightly shorten its upper part.
5. We will protect our giant tire from leaks with the help of rubber mastics for waterproofing. Pour its thick mass into the middle of the tire. pour a little - a small layer of it is enough for waterproofing.
6. Use thin sheet iron around tire circumference create formwork.
7. We stack reinforcing bar and fill with cement mixture.
8. The edges and bottom of our fountain decorate all the same small non-sharp boulders and pebbles.
9. Well, in the middle of the fountain put the pump with a special nozzle to spray water.

Wheel pool

As in the case of the fountain, the pool needs a large tire of some sort. trucks or large special equipment.

The used tires of the Belaz dump truck, L-170 or T-150 tractors are perfect. A popular option is from the K 700 tire.

materials

To create a pool from a wheel, we take the following materials and tools:

• half a bag of cement and sand;
• some laundry soap;
• a hacksaw, as well as a well-sharpened knife;
• paint and stones for decoration.

Process of creation

First we prepare the tire. one of her side part cut with a sharp knife. We leave only the side. For the pool, such a shortened tire is quite enough. To make it easier to wield a knife, we lubricate the place on the tire where we are going to cut with laundry soap.

Now we are preparing a place where we will put the tire.

To start we clean the site: remove the roots of trees, level the soil with a rake.

Then dig a hole. There are several options, depending on how the future reservoir appears:

1. If you need him to be partially dug in, depth and diameter should be approximately two thirds of the diameter and height of the shortened tire. When dug, we create a 15-centimeter gravel or sand cushion at the bottom of the pit so that it takes on the pressure of the tire and water. The pillow is well aligned.
2. If you want the pool was not buried, we make the pit wider than the tire diameter by approximately one spade bayonet. We fill such a recess with sand and carefully tamp.

Be sure to use cement (it will need 2-3 buckets) we strengthen the loose circumference of the recess.

Next, we put a tire in it, and in the hole pour one and a half buckets of cement. The binder material must be carefully leveled to seal the future pool, remove all cracks and protect it from leaks.

The cement will dry and set well in 2-3 days.

drain cock

It is necessary to create a special tap to drain and replace water in the pool. We will need:

• a pipe with a faucet and a corner for a pipe;
• washers (large diameter);
• nut and locknut (second nut to be screwed onto the bolt).

The drain cock is most conveniently placed on the side at the bottom of the tire:

• we attach a corner to the pipe with a faucet;
• make a small hole at the bottom of the tire;
• we cut the pipe, connect it with a nut, a lock nut and a large diameter washer.

Decor

Now it remains to paint the pool and lay out the stone wall. In the photo, a decorative springboard is also laid out of stones. The pool is covered with a protective mesh.

This video describes the creation of a film pond with the participation of old tire from passenger car:

Conclusion

It takes quite a bit of effort and patience to recycle tires wisely and create beautiful and useful water bodies from them. Do-it-yourself ponds and pools for summer cottages will please the eye for many years to come.

If there is a desire and tires remain, you can not be limited to a reservoir on the site: old rubber is useful for creating, and even.

In contact with

The dacha has great creative potential, as it has a lot of space for implementation. design solutions. The atmosphere in the country should be created comfortable and conducive to quality rest. Water has an exceptional effect on the atmosphere in the garden, as it creates a feeling of calmness and unity with nature. It is thanks to its properties that the presence of a reservoir in the country attracts many owners. Today we will consider a method with minimal physical and financial costs to build a pond from improvised material - tires. Also don't forget to tell us about your DIY tire pond experience.

Pond wears special meaning c, as it gives a special spiritual appeal to giving. Many do not even imagine a vacation away from the water.

The advantages of ponds are obvious:

• Flexibility of construction. You can equip a pond with various decor;
• In the pond you can settle fish or unusual plants;
• The presence of water on the site allows you to ozonize the air and create the impression of freshness;
• There are a lot of options for arranging a pond, given the variety of natural materials and the abundance of design solutions, you can create truly unique decors;
• The reservoir provides moisture to nearby plants, giving them a green and healthy look;
• An additional recreation area is being created. You can just sit and watch the water flow and the movement of the fish;
• Perfectly complements any.

Ponds in dachas (we will talk about how to make a country pond out of a wheel below) perfectly compensate for the lack of unity with nature and create an ideal microclimate in a plot with a beautiful landscape of water. One of the directions in creating ponds is a variant made from car tires, which will perfectly help replace artificial reservoirs.

What's special about a tire pond?

The key undeniable advantages of this type of tanks are:

• Durability of materials. Rubber and insulation can last for decades at correct device;
• High reservoir strength;
• Can do ponds various sizes;
• Rubber perfectly tolerates low temperatures and does not deteriorate under the influence of ultraviolet radiation;
• Although rubber is not an environmentally friendly material, it does not transmit harmful substances, especially from above it is covered with a layer of waterproofing. Therefore, such a pond can be used as an aquarium;
• It has a solid frame, which allows you not to create walls, but only the bottom;
• There is the possibility of painting in any color you like;
• The tire lends itself well to decoration;
• The tire itself is usually obtained free of charge or for a small fee (if relatives or friends have old, unnecessary tires that they want to throw away or from employees in a tire shop);
• You can install tires yourself, without hiring specialists;
• In the process of transportation or installation, the form is not damaged, it only bends;
• Due to the elasticity of the material, the tire can take the shape of an oval.

Photos of different design options

There are not so many types of ponds made from tires, in most cases they differ in decor. By functional types only a few varieties can be distinguished:

• Ordinary pond with a round shape;

• Cascade type, where a waterfall system is used, when water fills one tank, then falls into another;

• A group of ponds, thus, is equipped immediately with 2-3 or more tires. It looks good when they have different sizes;

• With a fountain Even in a relatively small pond, you can make a fountain that will decorate the site.

In terms of decor, the choice is quite large, but the emphasis is mainly on natural materials, so the arrangement of a pond often requires:

• Stones - mostly natural types, perhaps they will be turned, decorative or acute-angled stones;
• Greenery. You can create a real oasis with green spaces growing both in the pond itself and beyond;
• Lighting. You can make pool lighting from the tire from the inside or outside;
• Decorative figurines. They can be made from leftovers or other tires, also sold various options in country stores.

In general, you can use everything that is enough for imagination in making your own pond.

How to choose a place?

Mostly a reservoir is created for some reason. Pursuing it, it becomes more obvious where it is better to equip our facility. Mostly the pond has some kind of decorative value (we talked about how to make the pond decorative below), which can complement the appearance of the site in general or create a nook in it.

It is advisable to place our small lake in the center of the site so that it is visible from any angle and immediately gets the attention of guests.

For correct location pond, it is necessary to take into account several main factors that will affect the decision:

• Plot dimensions. If it is large enough, then visibility will not work, it is better to equip it in some open and noticeable place. Another relevant tip is to make a pond near the gazebo or the place where you spend most of your time;
• Land form. Mainly choose a rectangular area, if it is very elongated, then it is worth considering the location in the center free space where there are no buildings;
• The size and decor of the pond itself. If you take a large tire or prepare a cascade, you will need a large plot of land that is as clean as possible from construction debris and trees. Weeds are not a problem, they are easy to eliminate. The decor affects the size, if there is a desire to equip a fountain, lighting or similar elements, you will have to make a pond bigger size;
• Soil type. If the surface is loose, dirty, or has bad smell, it is better to move the structure to another place;
• Is groundwater present under the top of the earth. If there is groundwater nearby, it will be easy to provide a constant flow of water, but the bottom should not reach directly to the stream.

What tires are needed?

To correctly determine a suitable tire, you must first know the planned dimensions of the structure. If you are planning a very small pond, which will be a replacement for an outdoor aquarium, you can choose a tire from an ordinary car. To build a larger structure, you will have to pick up a larger caliber - from a truck, for example, KamAZ, a tractor or a bus.

The easiest way to get the necessary tire is to ask at a car repair shop or tire fitting, where it will be sold for a small cost. For specific tires, for example, from KamAZ, you can ask for the necessary frame in the workshop from the service center of the car company. Sometimes they can be found in ads ( on Avito or Yulia) or independently post an application for the purchase of a tire.

What will be needed at work?

To perform a high-quality arrangement of a pond using tires, it is necessary to first prepare a tool, mainly a garden one, which is in every household:

• Roulette ( meter);
• Level;
• Shovel;
• Electric jigsaw for cutting tires. If it is not available, you can take a hand saw for metal.

In addition to the tool, you still need to prepare the material:

• Tire. In addition to the fact that it needs to be obtained, it must also be cleaned of dirt, fuel oil and other unwanted precipitation. In general, the cover is unsuitable for the preparation of the reservoir, since the upper edge hides most of the entire reservoir. To do this, cut off the top of the tire, using an electric jigsaw or hacksaw;

• Stones for decoration. most accessible and beautiful way to create an attractive and natural look is natural stones that hides the rubber;
• Waterproofing film that will prevent water leakage;
• Adhesive for arranging the tank from the inside and outside;
• The rest of the decor and greenery is determined according to your desires, the same applies to lighting and a fountain.

Beginning of work

A pit is first dug out into which the tire will be laid. It is possible that it will lie on top of the ground, this option is simpler, but it does not look a little aesthetically pleasing, although it all depends on the quality of the design and the idea.

To determine the dimensions of the pit, it is necessary to replace the thickness of the tire and its width. It is worth considering that the dug hole should be somewhat larger in width in order to lay it neatly and without deformation and ensure a strong bond. It is also worth using a level so that the surface is perfectly flat, otherwise the water will be at an angle.

Important! So that the impromptu pond does not become heavily clogged, it is worth raising it slightly above the surface level.

Wheel waterproofing

To prevent high water consumption, it is necessary to lay waterproofing, which is given great attention. The bottom is especially important. The most common and available material It is PVC film made of polyethylene. Unfortunately, the film breaks quite simply and can hardly withstand the load. It is better to lay the film in at least several layers. Ideally, another material with greater reliability should be preferred. There are also other materials with which you can make waterproofing, the most popular are: liquid rubber, liquid glass and polyurethane mastic.

Buying material for pools, it will be possible to ensure the durability of the pond and simple operation. A layer of waterproofing is also laid inside the tire, but only after it is already on the ground. The film should go beyond the edges of the reservoir by 0.5 m so that it does not slip and leak. Excess film is removed only after final installation when the product takes shape.

Important! Before laying the film, it is necessary to remove all sharp and protruding elements: snags, nails, sharp edges of stones, construction debris and other elements. Otherwise, the film will tear and you will have to redo a lot.

strengthening

To prevent vibrations and slipping of the tire together with the film, it is necessary to fill the frame along the edges with sand or crushed stone of fraction 0-5, 5-10. This will also provide some buffer zone between the weeds and the stake. If there is no such material under the other, then the earth will do..

decoration

To create a unique, attractive appearance, which will decorate the site, decor is used. The most common decoration methods:

• Plants are planted at the bottom of the pond. They are usually sold in containers ready to use;
• Plants in tubs and pots that are installed on the shore. The advantage of this option is the ability to change the location of the elements and thereby create a unique design;
• Fish room with bright colors;
• Creation of compositions from natural materials, for example, stones.

To prepare a more beautiful composition, it is better to alternate the sizes of stones and their shapes.

Fish for the wheel pond

You can run in an impromptu aquarium:

• goldfish;
• Shubunkin;
• comet;
• golden horp;
• Koi (large tire ponds only)
• Minnow.

Tire pond plants

There are quite a few types:

• Lotus;
• Brazania;
• Zherushnik;
• Wolfia;
• Azola;
• Vodokras;
• Luronium;
• Pemphigus;
• Urut;
• Waterwort;
• Elodea.

Step-by-step analysis of creating a pond from wheels

Now let's go through the whole process step by step:

1. Determination of the place where the pond will be located;
2. Digging a hole for laying inside the tire;
3. Elimination of the upper edge of the tire so that the border is smooth and without large roundings;
4. Make a sand base according to the level;
5. Tire laying;
6. Waterproofing is laid on top of the frame;
7. The edges should be sprinkled with sand, it should hide the rubber and create stability;
8. laying stones;
9. At the final stage, decoration is done, plants are placed and fish are launched.

We hope that we have helped you understand the issue and now you know how to make a pond out of a wheel with your own hands.

Useful videos

Conclusion

The pond will become the highlight and the most popular summer cottage, so it is better to do it near the gazebo, it is also recommended to install benches, swings, and recreation areas nearby. It is worth remembering that the condition of the water should be monitored, periodically changing it, but the design itself does not need maintenance. For the winter, the water is simply drained, and the plants are removed, and upon the onset of warmth, everything returns to its place.

In addition, its assembly does not require a lot of materials, some of them do not even have to be bought. To create a pond from a tire, you do not need certain knowledge and skills.

Materials and tools

In order to make a decorative pond in your country house, you will need:

• tire from the wheel of a large car (KAMAZ, MAZ, tractor, etc.);
• ordinary shovel;
• stones different sizes(to decorate and define boundaries);
• fine sand;
• pebbles or gravel, or pebbles collected on the nearest river (to cover the bottom of the pond);
• covering material or thick oilcloth.

Covering material can be purchased at garden stores, or at stores selling pools. It is preferable to oilcloth, as it is much stronger and will last forever.

But if it is not possible to purchase it, you can use a thick oilcloth. Since it is not so strong, it is better to fold it 3-4 times. Be prepared for the fact that next year the bottom will have to be re-layed, because the oilcloth can leak.

Do you want to decorate your garden plot? Read.

Find out about planting thuja Smaragd and the rules for caring for it.

Step by step instructions for making a tire pond

Armed with everything you need, you can get down to business:

1. Step 1. We need to find a suitable place for the future pond. It is not necessary to have a lot of space, the main thing is that the tire fits.

If you want to make a recreation area around the pond, look for a larger area. You can place a bench or swing on the shore of the pond.

The layer of sand should be so thick that the earth does not show through it.

Stones can be of any size. First lay out those that are larger, and then, accordingly, smaller ones. So it will be more harmonious and beautiful.

You can put any number of stones. It can be in one or two layers, to mark the boundaries, or it can be in several layers, making walls.

Lay stones around the pond

• Step 10 Cover the bottom of the pond with pebbles or gravel. You can also collect stones from the nearest river, in this case it is recommended to wash the stones so that the water does not darken ahead of time. The layer of pebbles or gravel does not have to be made thick, the main thing is that the bottom is completely filled and all this beauty is visible through the water, and not the emerging covering material.

Do-it-yourself tire pond is ready. At this stage, the work can be considered completed. But if you want the pond to become even more beautiful, you can decorate it.

How to make drainage with your own hands on the site, read in.

Decoration of the pond and the area around it

At the end of the process, decorate the pond with ornamental plants

In addition to putting beautiful pebbles on the bottom of the pond and around it, you can also decorate the area around the pond.