Swivel table for cake with their own hands. Spinning table for decorating cakes what to use instead of a rotating table for cake
There is such a thing as a turntable. Some use it for presentations, of any souvenirs. Confectioners are used to rotate the cake during the manufacture of the latter. I decided to make a turning table with my own hands to show my homemakes, such as "3D". The Motor was based on the basis of microwave oven. Makes almost 3 turns per minute. It feeds on the household network 220V.
For the design of the table we will need:
- a circle of plywood;
- rectangle from plywood;
- switch;
- aluminum corner, for fastening the switch;
- Network cord;
- screws 10 pieces;
- Motor from the microwave oven.
The first stage in our foundation was done by cutting under the motor. I got somehow crookedly, but not the essence, closes the table by myself. The size of the base is 250mm * 100mm, plywood thickness 18mm.
In the pancake table, drills a hole with a diameter of 6 mm, the axis of the motor is 6.5 mm. The hole is not pass through, but exactly the length of the axis of the motor (about 10 mm). We try. Enters tight. If you drill the same diameter as the axis of the motor, then the pancake will hang out. It will have to glue, and this is an extra time for the manufacture of homemade.
Be sure to look at the motor. There are no 220V. I came across 21B. In the latter case, a transformer is needed, you can drive from the control board of the same furnace.
Since I have Plywood, I decided to paint the pancake and the base of the table from the canister. There was a matte paint in black. Everything dried quickly. Along the way, drilled a hole to make the wires.
After drying the paint, we screw the motor to its permanent place. I took the screw from the old printer. Very successful due to a wide hat.
Take the wire into the hole from the bottom of the structure. We connect the switch, I have a TP 1-2 toggle switch. Corner crepaim to base. Cover to the corner toggle switch. If there is no corner like me and the other switch, you can make anything for your needs.
So that the design did not go on the table, I decided to install rubber legs. In the role of the legs applied caps from the medication. In general, it is very convenient to use similar legs in the manufacture of hulls, homemade. Rubber is very elastic. Screw them to all the same screws from the printer.
Damn table in my case 230 mm. Thickness are all the same 18 mm, as at the base. For my needs it will completely come down. Here is a table I turned out. I repeat, per minute makes almost 3 turns.
Spinning table
Built a table spinning. Suitable for the decoration of cakes and for modeling (including dolls - heads). They blinded it, as it is called, from what was. But it turns excellently (so far without a cake), even in the field of wonders play or casino open! :)
What I needed:
1) Stand under the hot (round rug with a pattern of the ball - bought on a sale at the metro store for 3 UAH.), Diameter 38 cm;
2) a piece of fiberboard (from it weeping the circle with a diameter of 1 cm less than the stand under hot -37 cm);
3) Wheel for furniture on bearings and bonded by screw and nut (to disassemble it was easier) - I bought it on the market for 12 UAH;
4) 4 screws, 4 nuts, 4 washers (take a wheel with you to the store and select the length of the screw to it, so that its length does not interfere with the free to rotate the table, and even note that it should be recessed in the Fiberboard and do not perform above the surface of the table so the hat should be flat);
5) 4 screws of 5-6 cm long;
7) drill and drill for self-tapping screws and drill a large diameter to deepen a hole to blear the helical cap;
8) a tree bar length about 60 cm (I don't know exactly for sure, it is better to choose a specific wheel to be wider than the distance between the wings of the wheel base (so that
9) sandpaper in order to clean the edges of the Fiberboard;
10) Victor and nut roaster, size 6, suitable length (cm 5-6);
11) Glue "Dragon"
First of all, you need to cut off from the fiberboard the desired diameter. From the center to make 4 holes (applying the base of the wheel). The edges of the Fiberboard need to sand and stick with scotch.
Then we wear the base of the wheel on a piece of timber (slightly subscribe, so that it was perfect), we place and drill the hole for the fastening.
Attach the base of the wheel to our countertop.
At the wooden bar, we attach additional parts from the bar (so that the table is steady), fastened on the self-tapping screw.
We connect the top with the base and fasten.
On the tabletop we applied spiral glue "Dragon" from the edges to the center. We apply our rug - the stand is under the hot and again separate, we are waiting for a couple of minutes, so that the glue thickens and apply again to the tabletop. Take a table top down and, gently pressing, try to try the tabletop on the back, so that the glue took well.
All is ready!
If there is a desire, then the feet of the table can be somehow decorated - paint, toss, etc.
In the arsenal of each pastry, there must be a swivel for cakes.
With it, it is possible to significantly alleviate the process of decorating cakes and make it pleasant, comfortable and safe.
If buying in the near future is not planned, then an experienced master Can collect it yourself.
If you want a cake to be available to you from all sides at the same time, and at the same time you should not run around it, be sure to think about the presence of a rotating stand.
What is the rotary design for cakes? This is a product consisting of:
- round working surface;
- - relations;
- rollers, rubber bands.
Thanks to its design, the table is easily rotated around its axis, and provides convenient access to the confectionery product.. With such a delivery, you can most conveniently create elegant and original decors and form decorations of any complexity. In this case, you can absolutely not worry that your masterpiece will eat, damaged or falls to the floor.
A swivel table for cakes can be purchased in the finished form and make it on their own. Homemade design has a lot of advantages. First, you can make a product that fully meets your requirements and preferences.. Secondly, you yourself will be able to create a thoughtful drawing of the product, pick up the materials of its manufacture and think over the most optimal dimensions. In addition, homemade design It will be much cheaper than purchased.
Materials
A spinning table can be made of any kind materials:
Each individual option has its advantages. The tree is characterized by environmental friendliness, safety, pleasant to the touch texture. MDF and Plywood are easily processing. In addition, this material has a small cost.
But the chipboard is inexpensive, and his appearance is attractive, and it's nice to work with him.
Council: in order to save supplies, for the manufacture of countertops you can use the door from the old kitchen headset.
Tools
Having decided to make a rotating table for cakes with your own hands, prepare the following tools and materials:
Important: Bearings are double and pressed. The second option is preferable to assembling the rotating coach for the cake, as they are more convenient in the installation.
How to make a rotating table?
Make a swivel table is quite easy and simple. First, you will need to make a competently thought out sketch. In this drawing, specify the product design, its exact dimensions and manufacturing materials. Having at hand such a scheme, you can easily assemble a table from the first time and without errors.
The process of manufacturing the turntable is carried out in the following sequence:
That's the whole is not a complex process of manufacturing a rotating structure.
Council: To give a decorative product appearanceIt can be saved with thin plastic.
Also, the product can be decorated with self-adhesive film. It is just glued and easily clean.
A photo
Semit various materials And approaching the question creatively, you can get very different tables.
Confets engaged in the manufacture of cakes, it is very convenient to use different kinds of devices that facilitate the process of decorating the finished product. Benefit Today, stores offer a wide range of such inventory. One of these devices is a turning table. True, the cost of such a table is very large, and often easier and more profitable to try to make a swivel table for the cake with their own hands.
What is convenient?
Such a table will be useful not only to seasoning consumerism-professionals. It will be very useful as lovers to prepare in his pleasure, and makes the first steps to culinary. Very, by the way, this table of hostesses, adorning cakes by mastic. It looks like a circle pedestal on a leg, which spins around his axis. The main goal is to make the work of the confectioner as ergonomic and convenient as possible, simplify the task of decorating the finished cake. The cake is placed on the stand, and, rotating it, you can easily trim it with mastic, decorate figures, inscriptions and other decor. It does not need to go around it, the confectionery will rotate on the stand, and the hostess will have access to any place of cake.
What you need
In order to make a swivel table for the cake with their own hands, you will need:
- Bearings - 2 pcs. It is better to use double compressable bearings.
- Wooden blank for a circle. It can be the door from old furniture Or any chipboard material available.
- Nails.
- Saws.
- Tube (from plastic or iron).
- Circle of iron (metallic).
- Plywood sheet.
- Plastic or decorative self-adhesive film.
How to make a swivel table with your own hands
This process is not too complicated, but requires male participation. To begin with, it is worth drawing a drawing of the future stand and prepare all the necessary elements.
If the bearing is not double, then two will be required, and one should fit into another.
- Press the smaller bearing to more using nails.
- From the harvesting of the chipboard (or the old door), we cut two circles with a diameter of 20 cm with an electric bike.
- In one of them in the center you should make a hole in which the bearing is placed. It is this technique and will ensure the rotation of the entire mechanism.
- The second circle with self-drawers (you can use liquid nails) Brepim to the first.
- The bottom circle that does not have holes will stand directly on the table.
- Then plastic tube is inserted into the bearing (you can use iron, if any). It will connect the base and the top - pedestal for the cake. The tube must very exactly enter the bearing so that it does not hang out, otherwise it will be difficult to use the turning table. The optimal length of the connective tube is 15-18 cm. In this case, it will not be too short and too long, to use the device as convenient as possible.
- The top (the stand itself on which the cake is placed) is better made of metal. A metallic circle is required in diameter 30-40 centimeters. It is attached to the top of the tube (metal or plastic) with welding. Of course, not everyone has a house at hand welding machine And a person knowing how to do it. In this case, it is possible to use cold welding, resembling plasticine.
- To the top of the metal circle, the faeer or chipboard is fastened, equal to the diameter of a metal circle using liquid nails or self-tapping screws.
Now the swivel table for the cake is almost ready. It remains only to add it aesthetics. For this, the top is covered with wallpaper or plastic round base. This will give the adaptation completed and facilitate care.
As you can see, if you wish to make a swivel table for a cake, with your own hands, it is not difficult. A set of materials for its assembly can be found in almost any house, and the work process itself is not as complicated.
What can replace the turning table for the cake
What is the output of those who have no turning table? Very simple and affordable solution also have in almost any home. You can use a spin plate from the microwave. Almost all models are arranged so that they have a glass plate and a round stand from below. It is necessary to get a plate from the microwave and a circle under it. If too smooth, you can put down the paper (paper towel) to reduce slip. Thus, you can decorate the cake, smoothly rotating it around the axis. Also glass plate It will not spoil the view when filing a finished decorated product.
A swivel table for cake with their own hands is needed not only to seasoning confers. This is the necessary subject for those who prepare for their pleasure. Do not do without such a design by hostesses who baked coated cakes from mastic. The main purpose that has a spinning table is to facilitate the process of decorating the cake. That is, you do not have to go around yes near the finished product, it will be enough to just decorate a rotating cake. Baking is spinning around your axis, and you just need to decorate it.
How to make a turntable? To begin with, prepare everything necessary materials. You will need two bearings that can be purchased in auto parts stores.
Pay attention to the fact that there are double, compressed bearings. The second option is preferable because you have to tinker less.
The rotating table needs both in a wooden plate. You can stock door from the kitchen headset. In addition, they will need hard nails, self-tapping screws, plastic tubes, metal circle, thin plastic, plywood.
Work process
Scheme drawing
Rotary table with your own hands is quite simple. First of all, you will need to draw a quality drawing. After that, we start working according to the following scheme. If you have two bearings, and not one pressed, then you score a smaller diameter element to a larger with nails. In a wooden plate, it is necessary to cut two circle with a diameter of 20 cm. In one of the circles, the hole is muffled in which the bearing is clogged. In this case, the two parts are twisted and fixed with self-draws. Bearing is placed in the center.
The table is equipped with plastic tubes. The tube must connect the upper and lower parts. Consider this moment when you do the drawing for the turntable. In this case, the tube must accurately enter the bearing. The ideal length is considered 15 cm. Such a tube will not be too short or long, so you do not have to bend in the process of decorating the product.
The top is made of metal. In order for it to spin, pay special attention to its diameter. On average, the diameter of the metal circle should fluctuate from 30 to 40 cm. If you have the ability to cook the items, it will be only wonderful. For those who are deprived of such an opportunity, cold welding is invented, which externally resembles plasticine. Rotary table for cake requires circles cut from plywood. The rotating portion is installed on the pipe, and the elements are fastened with the help of screws.
1
2
3
4
5
6
7
The table can be made of wood:
Turning table for cake
Bearing knot assembly
Base for table tops rotating part collected
Rotary table for cake (bottom view) Turning table for cake (side view)
