Do-it-yourself trailer for a walk-behind tractor from scrap materials. Homemade dump trailer for the walk-behind tractor salute Drawings and dimensions of factory trailers for the walk-behind tractor

One of the most useful things in the garden is a walk-behind tractor. Besides, it will come in handy in the garden. With its help, you can easily cultivate land plots, as well as transport some goods: straw, vegetables, fruits, inventory, and the like. However, without a trailer it will not be possible to do all of the above. In this case, it is appropriate to tell you how to make a trolley for a walk-behind tractor with your own hands. This is the best way to save money. Also, to study, the topic "" will be useful, with useful photos and video materials.

Drawings of homemade trolleys for a walk-behind tractor

It is noteworthy that the made trolley will be able to carry a load weighing up to five hundred kilograms, as well as a driver. That's about seven full bags of potatoes.

We present to your attention a drawing of the cart:

1. Mounts for suspension devices walk-behind tractor (brackets).

2. Cantilever beam

3. Drove

4. Footrest (from 20 board)

5. Driver's seat

6. Main frame

7. Body part

8. Support beam made of timber

9. M8 bolt

10. Thrust ring made of pipe

11. Stroller wheel.

The carrier is designed to support only a few parts of the cart. They are fastened together by welding. Obviously, the most loaded part is the drawbar coupling, as well as the turning part. Therefore, it is necessary to install stiffeners in this part of the structure.

Frame

The frame can be assembled from steel corners and pipes of round and rectangular cross-section. At first glance, the structure is very complex and has a large margin of safety. But it should be noted that the transport will be used in difficult conditions. Therefore, all questions regarding strength disappear.

Drawing and dimensions of the trolley frame for the walk-behind tractor

1. A slope from a metal corner.

2. Frame for driver's seat

3. Riser made of pipe

4. Racks of the driver's seat, made of the corner.

5,14. Front struts from the pipe

6,15. Longitudinal side members from corner

7,8. Supports for wheel axles.

9,16. Back braces made of pipes

10. Cross member for reinforcement, made of corner

11. Longitudinal joint housing

12. Wheel axle

13,17. Transverse spars

18. Kerchiefs.

However, if the loads are not so large-scale, then simpler structural solutions can be chosen (see).

Carriage carrier

The wheel axle is made of a steel round billet with a diameter of 30 millimeters. If the axle length is one meter, then the wheels will be located under the body. The axle of the wheels with corner supports, as well as a gusset, is welded together with the side members, as well as the body of the longitudinal hinge.

Body - dimensions and main parts

The trolley body is made of 20 mm thick boards. At the corners of the boards, you need to fix the corners of steel. With the help of three beams, the body is attached to the bogie frame itself. The beams consist of 50 to 50 beams.

Wheels

The trolley wheels can be used from the stroller. The hub is assembled. The ends of the axle must be sharpened to match the diameter of the bearings.

Sintering with walk-behind tractor

With the help of a cantilever beam, the cart is connected to the walk-behind tractor. The upper part of the console is similar to the contour of the handle. It is mounted in the bracket of the hinged devices of the walk-behind tractor.

When the cart is operated in difficult conditions, it is necessary that its connection to the walk-behind tractor be articulated.

The drawbar must be inserted into the tubular body of the hinge. The drawbar is fixed with a thrust ring. With the help of this design, it is possible to achieve independence of the wheels of the trolley from the wheels of the walk-behind tractor. When driving with a loaded cart, this allows better control of the walk-behind tractor.

Swivel unit - diagram

1. Console;

2. Anthers;

3.6 Bearings (36206);

4. Housing;

5. Spacer sleeve;

7. The sleeve is remote;

9. Nut М20 * 2.5;

10. Oiler;

The driver will sit on a cushion, which has medium hardness, because it is made of wood. The driver's seat is in front of the body. Management is carried out from the cart. The operator's hands hold the handle of the walk-behind tractor.

Cart design

A trolley of any design has the following parts:

Place for the driver;

Trolley with a body;

What material is suitable for the trolley frame?

It is best to prepare the frame for the cart from the corners and the channel. They can be bought in almost any building hypermarket or base. It is important to cook the frame very carefully. The structure must withstand movement with loads on difficult road sections.

Wheel axle blank

For the wheel axle, you can use steel wheels that have a diameter of 30 millimeters. The axle is connected to the longitudinal hinge by means of welding. It is important to choose an axle so that the wheels are located under the body.

How to make a trolley body

You can independently make a body for a trolley from boards that are 20 millimeters thick. Steel corners are attached to the corners of the boards. With their help, the body is bolted to the frame. The best option is drop sides. So it will be possible to easily remove loads, and also put them on a wagon.

Wheels - what will fit

In principle, the wheels can be taken from any agricultural equipment. In addition, some craftsmen use wheels from motorcycle equipment, as well as from wheelchairs. But the axle will have to be turned to fit the diameter of the bearings.

Trailer hitch

The hitch can be made from any piece of metal. It is necessary to drill a hole in it, which will be used for the hitch. The swivel unit is necessarily used with a bearing. It is important to strengthen it as firmly as possible by welding.

Bottom of the cart

The bottom of the cart can even be made from edged boards. However, it is best to use 2mm steel. As a result, you get a trailer for a walk-behind tractor, which can serve for several years without service. All materials for the manufacture can be easily found in any hardware store. The tool is sure to be found in every home. Unless you can rent electric welding.

When making a trailer for a walk-behind tractor with your own hands, it is important to take into account that every detail must be made as accurately as possible. The quality and durability of the product depends on this. You can get the job done in just a few days.

Video examples of making homemade carts

Detailed video instructions for making a homemade cart, showing what and how to do.

Another example of high-quality homemade products.

Equipment such as walk-behind tractors has long taken root among summer residents. Of course, this is a great assistant, which is designed to reduce labor intensity. earthworks... But it is difficult to underestimate the need for a high-quality trailer for a walk-behind tractor. It can be used for a wide variety of purposes, from transporting seedlings to crops or heavy tools. Let's talk about how to make a trailer for a walk-behind tractor with your own hands. Let's start from the very beginning.

About the characteristics and price of trailers

Before going directly to the topic, I would like to consider a few basic characteristics inherent in any trailers for walk-behind trailers. First, it is their carrying capacity. It is impractical to make a trailer that will not be able to carry even 300 kilograms, so we will build on this minimum. As for the maximum carrying capacity, it should be no more than a ton. It is unlikely that the walk-behind tractor will carry off more.

For example, an existing trailer for light motoblocks with a carrying capacity of 300 kg and dimensions of 1 mx0.85 cm costs about $ 200. If we take the technique for medium motoblocks, then their price rises to 250, and heavy - to 500. Agree, the numbers are not small. Nevertheless, you can make a trailer for a walk-behind tractor with your own hands without any problems and at the same time you will not spend a lot of money. It is always necessary to start by drawing up a drawing. Let's do it.

We make a trailer for the Neva walk-behind tractor with our own hands: drawings and highlights

Most modern adapters for motoblocks are made of galvanized steel. This solution is most advisable, since the trailer will serve for a long time. It is also recommended to make the bottom metal, it is an order of magnitude stronger - therefore, it will last longer. The drawings given in this article do not have to be used in the form in which they are submitted. You can sketch your own sketch with dimensions and types of fasteners and use it.

But it is still recommended to use ready-made drawings of the main elements. These include the connecting frame, body and carrier. You are probably wondering why this moment is so important. The thing is that you can easily make a trailer for the Neva walk-behind tractor with your own hands. The drawings also allow you to see the complex places of the structure, the methods of fastening and the places of connection of various nodes. Believe me, it's much easier to think through everything at once than to redo it later.

From simple to complex

First, I would like to consider the most simple model in terms of the complexity of manufacturing. In order to start assembly work, we need the following material:

steel pipes with a cross section of 60x30, as well as 25x25 mm;
wheels and springs;
sheet steel with a thickness of at least 0.8 mm;
duralumin sheet with a thickness of at least 2 mm;
channel and fasteners.

It is not hard to guess that you cannot do without the appropriate tool. You will need a grinder, jigsaw, welding machine, as well as a screwdriver.

The frame of the trailer in our case is a one-piece structure, which is placed on the frame grille. In order to equip it correctly, first we make two traverses 25x25 mm, which will be cross members. You can make side members from a 60x30 mm pipe. All elements are connected in such a way that the final result is a lattice.

We continue assembly work

After you have made the grating, two longitudinal pipes are welded to it, in the upper part of which a strapping of 25x25 mm is made and connected by welding. A self-made trailer for a walk-behind tractor, the photo of which you see in this article, has folding sides. Such a solution is most preferable and for its implementation the frames are made separately from the frame. Thin steel sheets can be used as the material for the sides.

Now we need to make a beam. This will require two channels that are inserted into each other. One of the ends is necessarily equipped with wheel axles. Now we need pre-prepared springs, with which we will connect the spar. To do this, the end of the springs is put on the shackle axle and the beam axle, and the central part is welded with ladders to the same beam. It remains to make the drawbar from pipes 60x30 mm. To do this, the pipes are joined and welded to the trailer, and the rear parts are welded to the side members.

We make a multifunctional trailer for the Zubr walk-behind tractor with our own hands

We have already figured out that before designing the adapter, it is necessary to draw up a drawing, which will indicate the main dimensions and general form products. Next, you need to make sure that all the materials are in our the required amount... For the coupling, we will use a channel, so you should also stock up on them. It is desirable to pay special attention to this stage. The fact is that if you buy too many fasteners and rolled metal products, then this is a waste of money, and an insufficient amount will entail reworking the structure, which is not good.

I would like to note that a trailer made without the use of welding, that is, on self-tapping screws, will not live long, you must understand this. Therefore, take the welding machine from your neighbors or friends for a while. To make a frame, you can take steel corners 50x25 and 40x40 mm. For the body, boards of 20 mm and a bar of 50x50 mm from which support beams will be made are suitable.

Making the base of the trailer

A do-it-yourself dump trailer for a walk-behind tractor can be made according to the existing structural diagram presented in this article. This trailer has 4 main components: wheels, carrier, frame and body. They are connected to each other by welding.

The body is almost entirely wooden, assembled from 20 mm boards, the corners of which are reinforced with metal corners. The body is fastened to the trailer frame by means of 3 support beams (bars 50x50). Since we are presented with a single-axis design, it is extremely important that the center of gravity is shifted to the front, but at the same time does not go beyond the axle of the wheels. The disadvantage of this design is that the sides are not folding. But by slightly improving the trailer, this defect can be eliminated. It is advisable to make side loops. They are needed to secure the load during transportation.

Trailer chassis

This stage is one of the most important. The fact is that if the undercarriage is made incorrectly, then one cannot count on the durability of such equipment. Therefore, pay special attention to this. What does not matter in our case is the wheels and springs. You don't have to buy new ones. The used wheels of any car are perfect, and the springs can be bought used from Moskvich.

In general, wheels from a motorcycle are suitable for assembly. It is advisable to remove them together with the hub. If the diameter of the rod and the hub bearing do not match, then the end of the rod must be sharpened. A good wheel axle can be obtained from a steel rod with a diameter of at least 30 mm. Its length must be such that the wheels do not protrude beyond the body rims. The bar is connected to the trailer by welding through the corner supports to the side members.

The final part of the assembly work

It remains to connect the trailer and the walk-behind tractor to each other. The console is used for this. It is desirable that it be attached to the bracket attachments... In this case, the carrier pivot unit must rotate freely in its lower part.

The drawbar is inserted into the tubular hinge body. It is best to fix it with a thrust ring. This solution is the most preferable, as it provides independent movement of the wheels of the walk-behind tractor and the trailer. This is extremely important when driving on bumps.

Conclusion

So we assembled a dump trailer for a walk-behind tractor with our own hands. All that's left to do is secure the driver's seat and kickstand. Management is carried out directly from the seat. If necessary, you can make a trailer with brakes for a walk-behind tractor with your own hands. True, this is not always necessary, since the connection described in this article does not provide for a large longitudinal movement, therefore, when the walk-behind tractor stops, the trailer will also become. That, in principle, is all on this topic. Now you know how to make a trailer. To do this, you will need a drawing, the necessary material and tools. And, of course, free time and desire. You don't need to be any kind of mechanic or designer for this.

Using a trailer for a walk-behind tractor can significantly expand the functionality of this popular technical tool. However, the purchase of a ready-made device is not feasible for all owners of personal plots from a financial point of view. In such a situation, you can think about making a trailer with your own hands.

Types and features of structures

Trailers have different carrying capacities, and this is one of the criteria used in their classification. Most often, at home, there is no need to use devices with a high lifting capacity. Besides, all trailers for a walk-behind tractor can be divided into groups according to their design:

Whole - have the most simple design, in which the bottom and walls are fixedly connected.
With drop sides - perfect for transporting bulky goods.
Tipper - convenient during unloading operations and allows increasing their productivity.

When planning to buy a trailer or make a cart for a walk-behind tractor with your own hands, it is important to take into account some design features.

If everything is quite simple with solid towing devices, then in the case of other types it must be done. ... Special attention should be paid to the following factors:

Making a trailer with your own hands

After studying all the design options in the manufacture of a homemade trailer for a walk-behind tractor, the most often used are simple options... The tipper device is certainly more difficult to make, but its functionality is much higher.

Work on creating a trailing device for a walk-behind tractor with your own hands begin with a drawing. Thanks to this, it is possible to determine the amount of materials required and select complex assemblies that require the development of more accurate schemes.

It should be remembered that the center of gravity of a well-balanced trailer should be located closer to the headboard, but at the same time not go beyond the level of the wheel axle.

Assembling the frame

The reliability of the frame is predetermined by the durability and strength that the hitch will have. This should be taken into account when creating a project for a future hitch. Thus, the following materials can be used in the manufacture of the trailer frame:

Quite a simple matter. Some homeowners decide to make more sophisticated devices. In such a situation, all subsequent actions depend on the choice of a specific type of trailer:

On a tipper hitch, the tailgate must be hinged.
If it is planned to manufacture a trailer with folding sides, then all three sides, except for the front one, should have such a design.
The frames of the folding elements should be made separately from the general frame. For simple models they can be common elements of it.

Frame sheathing

This is one of the most simple steps in creating a hitch. However, there are some nuances and they must be taken into account. To carry out work on the sheathing of the frame, it is worth choosing those materials that cannot increase the cost of the hitch:

First you need to sheathe the bottom (floor) of the trailer, and then tackle its sides.

Chassis

This structural element can be taken from an old vehicle such as a garden wheelbarrow. An additional pipe is required to secure it. The hub can be pressed in, and its rear part can be bored and fixed on the axle. In this case, it is extremely important to ensure that there are no distortions.

For wheel mounting the best option are the pins... They will provide a fairly reliable and durable connection. Bolted connections can be used to reinforce structures. The final stage of work on the manufacture of the chassis will be the fastening of the hubcaps.

After creating a hitch, it remains to make a hitch. it separate element, being at the same time very responsible. Most in a simple way the connection of the walk-behind tractor with the trailer is the "pipe-in-pipe" assembly. To one end pre- bent pipe in a vertical position, a short piece of pipe is attached.

At the opposite end of the main element (bent pipe), a second segment is welded, and it is necessary to fix a kingpin on it, which will act as a connecting element. it robust design easy to manufacture and highly reliable.

One of the most essential tools for every gardener, farmer or gardener who owns mechanized agricultural equipment is a walk-behind tractor trailer. Using a walk-behind tractor on the farm, you can plant, plow, cultivate. And if you attach a trailer to the walk-behind tractor, we will get an excellent assistant who can transport rather heavy loads. The dimensions of the trailer for the walk-behind tractor are calculated in such a way as to be a universal and multifunctional unit. They also make the farmer's work easier by tilting the body and opening the tailgate.

Optimal trailer dimensions for a walk-behind tractor

Most trailers can be operated seated thanks to the seat. Before choosing a trailer for a walk-behind tractor, you need to check its compatibility with the walk-behind tractor. You also need to take into account the strength of the frame and the thickness of the steel sheet, so that during the operation of the walk-behind tractor, the trailer does not deform.

Let's look at specific examples of what sizes trailers are.
Dump trailer PM-0.6S. The length of the trailer is 1400 mm. Trailer width 1000 mm. Loading capacity 350 kg.

Motoblock trailer with 7C springs. The length of the trailer is 2900 mm. Trailer width 1000 mm. Trailer height 1200 mm. Maximum lifting capacity 500 kg.

The trailer for the walk-behind tractor is homemade. The length of the trailer is 2250 mm. Trailer width 965 mm. Trailer height 885 mm. Loading capacity 400 kg.

Drawing of a trailer for a walk-behind tractor

This trailer can be used both with a walk-behind tractor and with a car, and is a transformed unit. Equipped with a simple sprung suspension.

One of the purposes of the trailer is the ability to transport the walk-behind tractor by car. The "Fork" unit allows one person to load and unload the walk-behind tractor without much physical effort.

With absence passenger car, the trailer is equipped with a body and connected to the walk-behind tractor. Instead of cutters, wheels are installed on the walk-behind tractor. The trailer has a good sprung suspension, which results in excellent ride softness, good longitudinal stability and almost no rigidity. Parts of the trailer can be easily disconnected, which allows compact storage of the trailer, disassembled.

The body length is 2320 mm, the width is 1590 mm, and the height is 500 mm. The track width is 1490 mm. Body dimensions: 1500 mm long, 1200 mm wide, 300 mm high. Fork size 500x300 mm.

Configuration options

All parts by detail

Trailer use options

Trailer dimensions

The main purpose of the trailer is to transport cargo. The trailer itself is an intermediate link in the transportation of cargo. Consequently, the primary task when creating a trailer is to achieve low weight and good lifting capacity. All elements of the trailer structure are used rationally. Chassis weight - 25 kg. The weight of the transported cargo is 200 kg. During storage, the trailer takes up very little space and fits easily into a car.

Equipment such as a walk-behind tractor is an excellent assistant when working in the field, garden, country house or farm. To expand the capabilities of the equipment, you can attach a trailing device to it and transport soil, garbage, crops, tools and other heavy or bulky goods. You can make a trailer for a walk-behind tractor with your own hands, spending only a few days on it. The result is an irreplaceable assistant that will facilitate further work.

Preparatory work

Firstly it is necessary to consider what size the trailer should beso that it fits a certain walk-behind tractor, and it is convenient to use it. After that, you will need to sketch a drawing or a sketch of the trolley, on which to display the structure from different angles, put down all the dimensions and draw the nodes.

Trailer mechanisms

You need to think over everything to the smallest detailso that during the assembly of the equipment there are no difficulties. To do this, you need to understand:

Having dealt with all these questions, you can start preparing list of required materials and calculation of the approximate cost of the future trailer.

Simple trailer for the "Neva" walk-behind tractor

To start making a cart with your own hands, you need to prepare the following materials and tools:

duralumin sheet with a thickness of 2 mm;
steel sheets with a thickness of 0.8 mm;
springs and wheels;
steel pipes 25x25 and 60x30 mm;
channel;
fasteners;
screwdriver;
welding machine;
jigsaw;
grinder.

Trailer frame will be one-piece constructioninstalled on a frame grille. For its manufacture, two traverses of 25x25 mm must be made transverse and pipes 60x30 mm must be attached to them so that the result is a lattice.

To the finished grid two longitudinal pipes are welded, on top of which a strapping of 25x25 mm is attached by welding. The material for the sides will be steel sheets, which are cut to the required size and welded.

The turn of the beam has come, for the manufacture of which two channels will be needed. The elements are inserted into each other, after which the wheel axles are put on one of the ends of the resulting part.

The spar is connected by means of springs, the end of which should be put on the beam axis and the shackle axis. Then, the central part of the springs must be welded to the same beam with stepladders.

Last but not least, do it yourself you need to make a drawbar from pipes 60x30 mm... They should be docked and, by welding, one part should be connected to the trailer, and the other to the side members.

A simple trailer for a walk-behind tractor is ready. I would like to note that experts recommend using a welding machine to connect its parts. Such a fastening will allow the structure to be operated for a long time.

Do-it-yourself multifunctional trailer for a walk-behind tractor: stages of work, video instructions

Having decided on the dimensions and sketching a drawing, how much should be calculated meters of rolled metal and how many channels will be needed to make a homemade trailer. This is necessary in order to protect yourself from unnecessary costs for the purchase of unnecessary parts and fasteners.

Required materials and tools:

welding machine;
steel corners 40x40 mm and 50x25 mm;
timber measuring 50x50 mm;
boards 20 mm thick;
trimming round and rectangular pipes;
complete wheels with hub.

Future trailer will consist of four main nodesconnected by welding.

Stages of work:

The dump trailer for the walk-behind tractor is ready. Now you can fix the footrest and the driver's seat from which the equipment will be controlled.

Homemade trailer for a walk-behind tractor from car parts

Having drawn up a drawing in advance and prepared necessary materials and tools, you can assemble such a trailer with your own hands in 1-2 days.

For work you will need:

front axle shafts from Zhiguli or Moskvich;
channel 65 mm along the body length;
corners 60x60 mm;
two pipes 2 m long;
one pipe 60x40 mm, 3-5 m long;
welding machine.

The bearing part of the structure will be axle, which is made from a channel... Its length depends on the length of the future trailer. On both sides of the channel, half-shafts from the car are attached by welding. Profile pipes are installed on top:

To ensure the structure is strong and rigid, from the front corners of the bogie profile corners or pipes should be pulled... The joints can be bolted or welded.

The trailer frame is ready. Now you can install a simple wooden body made by your own hands on it, a seat and attach it to a drawbar.

After watching the video instructions and studying the article, you can understand that in order to make a trailer for a walk-behind tractor with your own hands, you do not need to be a designer or mechanic. To implement the plan, you will need a drawing, necessary tools, materials and a little desire and free time.