DIY phone stand: how to make paper, wood. All options for creating a stand for a smartphone from a plastic card Stand for a phone hand

In our progressive times, it is difficult to meet a person who does not have a mobile phone. Even by sending a child to first grade, parents provide him with the necessary means of communication. We use modern mobile devices not only for communication, but also for gaming applications, typing, reading, as well as watching videos and much more. Often, the owner, who wants to have a phone always at hand, wants to arrange it in a convenient way... Various expensive holders are offered in stores, but from our article you will find out what you can make

Stationery binders

Surely those who study or work in the office will have several stationery clips called binders on their desktop. Next, let's look at how to make a phone stand out of these gadgets. To create a sturdy holder, you can use 1, 2, 3 or even more binders. Some craftsmen collect volumetric structures from many different sizes clip. But such stands look cumbersome and are inconvenient for temporary use. It is enough to fasten two binders together and do not forget to bend one metal end of the holder towards the phone located on it. Even one piece with a folded ear will be enough to support a mobile device.

From the same binders, you can build another structure by placing the clamps opposite each other so that the ears look to the sides. The phone is inserted into these ends, as in the grooves. To keep the clips stable, clamp a small cardboard on both sides.

Using pencils

If there are no binders at hand, the question may arise: how to make a phone stand from pencils. Before building this structure, prepare 4 rubber bands and 6 pencils. In fact, you need to assemble a three-dimensional geometric figure - a tetrahedron. The principle is that you need to fasten two pencils with an elastic band, and insert the third between the turns. It is advised to use pencils with an eraser on the end to prevent slipping on the table and a stronger grip on the phone.

Bottle models

IN household we use a variety of cleaning and detergents... Most of them are contained in plastic containers... It can be used as a mobile device holder. And how to make a phone stand out of a bottle, we will consider further.

The type of fixture will depend on the shape of the container. This can be a container for shampoo, shower gel, cleaning agent and other. Take a bottle twice as long as your phone. Cut off the neck and part of the container from one side to about the middle. All sizes are relative - measure at your discretion. Cut a hole in the opposite area of \u200b\u200bthe bottle that matches the parameters charger... You should end up with a detail that resembles a handbag or pocket with a handle. Place the phone in the cradle and connect the adapter to the mains through the hole. Your mobile communication device will not roll on the floor and there will be no risk of crushing it. You learned another way - how to make a phone stand. If desired, this holder can be painted, pasted over with beautiful paper or fabric.

Paper clips

The simplest and affordable option coasters are an ordinary metal clip. It must be unbent in a straight line and folded as shown in the diagram. The resulting product is quite sturdy and stable. This design perfectly holds the mobile phone without interfering with watching videos.

Cardboard and plastic cards

How to make a cardboard phone stand? You will need a piece of cardboard from which you will need to cut a 10 x 20 cm strip. Then fold it in half along short cuts. Next, draw a shape as shown in the photo below. The fold line must remain intact. Expanding the detail reveals that you have a comfortable and stable phone stand.

If you have an unnecessary card lying around (any discount card), it will also make an excellent phone stand. Making such a device at home is very simple. Step 1 cm from the edge of the card and fold the piece along the short side. Fold the rest of the card in half in the opposite direction. You will have a zigzag shape. Place the phone on the formed protrusion. The stand is ready.

Unusual coasters from simple things

Savvy people began to use ordinary glasses as a phone holder. They only need to be turned over with the bows up, which, in turn, must be crossed. The mobile device is positioned between the bezel and the temples that hold the phone.

How to make a phone stand from a construction set? In this case, it all depends on your creativity and imagination. To create such a model, you need to use a platform and a few bricks various shapes... A stand made of parts can hold the phone both vertically and horizontally. The tilt of the screen can be adjusted by adding or removing additional bricks.

One more interesting detail, which will help keep the phone upright - an old cassette holder. You must open it and flip the lid back, thereby turning the box out. In the hole that once served as a pocket for an audio cassette, you can put your communication device. The convenience of the stand is that it is quite durable and transparent, and does not interfere with the use of the phone. Plus, it can be easily washed.

As you can see, from the simplest items that can be found in every home, you can make such useful thinglike a phone stand.

Proposed for construction, a phone stand for a car will be extremely useful for drivers who often use a phone. She will solve problems with finding a phone during a trip. Thanks to the simple and robust design, the work will not take long.

Step 1. Tools.

To create a rack you will need:
1. Aluminum tube with a diameter of 47 mm "f. four";
2. Connecting angled tubes in 45 ° and 90 ° (aluminum or copper). They are cheap and sold in any hardware store

3. Solid wooden sticks (you can take ice cream sticks);
4. Epoxy glue or any other glue with similar qualities;
5. Phone case or case;
6. Cable ties (they will be needed to secure the cover);
7. Hacksaw;
8. Ruler;
9. Knife.

Step 2. Assembling the frame.
Before starting work, you should decide on the location of the telephone rack. It should not interfere with the use of the audio system, recharging and other daily activities in the car. Only then can you start measuring.

The aluminum tube needs to be cut into 3 pieces. The shortest part is attached to the 45 ° elbow tube. The horizontal part (about 5 cm) connects 90 ° and 45 ° angled tubes "f.2.1 - 2.2". A vertical tube (approximately 10-13 cm) will support the stand itself. All pipe connections must be lubricated with glue so that nothing falls off during movement.

Step 3. Attaching the cover.
On the back side of the cover we make 3 pairs of cuts (the depth of the cut should correspond to the tips of the ties). The incisions are parallel to the tube, which will subsequently be attached to the sheath. We pass the ties into the holes and tighten a little (the main thing is not to overdo it). We tighten the long tube of the frame with ties as shown in the photo. Cut off the ends if they are too long.

Next, you need to cut the wooden sticks in half, insert between the cover and aluminum tube and grease with glue.

The mobile phone has become an invariable attribute of a modern person. And on the road, and at home, and on the desktop, a useful gadget is assigned the main place, otherwise "suddenly someone calls, but I won't hear / see." For convenient placement of the cell on the table, they invented stands. You can buy them in the store, or you can do it yourself from scrap materials. Even the seemingly useless "unnecessary garbage", like cardboard packaging from dairy products or a long-used cover for a disc, will come in handy in work.

Cardboard stand

The first option is to make a mobile stand from cardboard. This is not necessarily a whole piece of material, you can take a used small volume milk bag (0.5 ml). In this case, you do not need to glue anything: you only need scissors.

The box must be thoroughly washed, crumpled and cut off the bottom. Then cut it along the folds.

The work will need a central part in the form of two rectangles. There is a fold between them. It needs to be cut and folded with the outside to the inside, pinching the fold with one hand.

Starting from the opposite end, from below, cut out a shape that resembles the letter "T". It is tapered upward, but has a beveled corner.

When the shape is expanded, the bottom edges become where the phone is. It rests on the central face. The budget stand is ready!

CD Cover Stand

Surely everyone has a couple of DVDs lying around in their house. One of the unnecessary covers can be turned into a cell phone stand.

To do this, cut the cover in half. Then cut off all holes and rivets so that only an even rectangle with two bent corners at the ends remains.

The plate must be clamped with tweezers or pliers and dipped in boiling water. This will make the plastic soft and pliable.

Holding the plate with pliers or any other tool, it must be bent so that one of the corner ends does not reach the other a little. 2-3 cm is enough, in this space the phone will be located. One of the corners is glued to the surface. The result is an interesting and lightweight stand. The device can be placed on it both vertically and horizontally!

Paper clip stand

A paper clip cell phone stand is an interesting thing that can be done in 2 minutes. To do this, you need a large massive paper clip, which you just need to unbend correctly!

To begin with, the wire is fully straightened into a line. Then you need to clamp it and bend it again:

1. Fold in the form of a tick - U.
2. Bend both ends at an angle of 90 ° C, starting approximately in the middle.
3. Bend the ends of each end slightly.

Thus, an ordinary paper clip has become a laconic stand. The phone lies horizontally on it.

Toilet roll stand

There is such good thing as a sleeve from a used toilet paper roll in every home! Do not rush to throw away the cardboard form - it can be turned into a mobile stand in a matter of minutes.

All that is required is to properly cut off a portion of the bushing at an angle. A small piece of cardboard should remain in front to create a stop. A phone that is too tall cannot fit on such a stand, but standard size "Sits down" perfectly.

If desired, the stand can be decorated: painted, wrapped with cloth or pasted over with paper for gifts. And no one will believe that she was once part of a toilet roll.

all work step by step

Output:

When working with familiar things, it is important to give free rein to imagination: try on, think, experiment. Then stands for mobile phones will appear in the house regularly - and always different and interesting!

How often, being at home, in the office or on the road, we cannot remember where we put our phone. To prevent this from happening, you should get comfortable and ergonomic stands that you can make yourself. The phone stand can be made with your own hands from the most unexpected materials at hand. How to do this, our step by step wizard class.

How to make a do-it-yourself phone stand: options for office and auto

Whether in the workplace or in the car, we all need to always be in touch. At the same time, I do not want to spend a lot of money on expensive coasters, because they can be made from waste materials that have served their life.

Card stand.

The simplest version of a phone holder is a card stand. To make it, you need to carefully bend an unnecessary plastic card in two places, as shown in the photo below, without allowing it to break.

Experience shows that the stand is plastic card is very reliable and can even withstand air travel in times of strong turbulence.

Stationery clip stand.

To make a phone stand from stationery clips or binders, as they are also called, you need one large and one small clip. The legs of the small clamp should be placed between the holding part of the large clamp and placed on the table so that the clamp bigger size leaned on its surface.

Similar coasters can be made in five minutes from clothespins.

Paper clips make a great option for a car stand. To make it, you need to disassemble a large clamp and slightly bend the metal parts, as shown in the photo below.

To avoid damaging the surface of the phone metal mounts it is recommended to wrap with threads in several layers. We return the holders to their place, additionally fix them with adhesive tape and clerical elastic band. We attach the clamp to the ventilation louvers. The phone is securely fastened between the metal parts of the binder.

Paper stand.

Plain office paper folded in a certain way can even support the weight of a large smartphone. To make a paper stand, you need to measure the dimensions of the phone and adjust the pattern below to fit them.

Cut the piece out of paper, fold it along the dotted lines and insert the side pieces into the slots. The good thing about this design is that you can charge your phone without removing it from the cradle.

We study popular options for coasters for home comfort

A desk phone stand for a home should be not only comfortable, but also durable, stylish and fit well into the interior of your home. Consider the options for such products.

Stand made of newspaper tubes.

This phone stand made of newspaper tubes will be a wonderful gift and an excellent decoration for any interior.

To weave such a stand, you will need several pre-painted long newspaper tubes, scissors, knitting needles, a little glue and varnish.

We place six blanks parallel to each other at a distance of about 1-1.5 cm and firmly fix them in the machine or in any convenient way. We put knitting needles or wire in the extreme racks, so that it is more convenient to form even and neat contours of the product. We begin to braid the base with a working tube using the "string" technique or chintz weaving. We monitor the parallelism of the rows and, if necessary, coat them with glue for better fixation.

We braid a rectangular blank of the required length. We take out the knitting needles or wire. We carefully fill and cut the ends of the racks. We give the workpiece the necessary curved shape, if necessary, slightly wetting it with water.

Likewise, weave the leg of the stand on a smaller number of tubes. We bend the finished leg, install it on the main part and fix its racks between the rows of the stand. We cut off and hide the excess. We coat the product with glue, if desired, paint it additionally and cover it with 1-2 layers of varnish. After complete drying, the stand can be used as intended.

A stand made of origami modules.

Modular origami is a fairly young, but very popular type of needlework. With its help, you can make many unusual and original gizmos, including a phone stand from modules.

To make the stand, you will need two-sided cyan and color pink... We cut the sheets into blanks and fold the modules.

We start weaving from the base of the stand. It requires 28 blue modules, which must be connected together and closed in a ring. In the same way, we make out three more rows. From the fifth row, we reduce the number of modules by 1, 2, 3, 4 pieces. In the seventh row, put one pink module in the middle.

In the eighth row we put 6 modules, make a pass, another 10 modules, a pass, 6 modules. The number of pink modules is 2 pieces. In the next row on pink patch we put three modules in pink. We begin to design the curly edging of the stand, as shown in the photo below.

In the back, we form a heart-shaped pattern, above which we install a number of modules blue... Gradually narrow the stand until a triangular wedge forms at the back of the stand.

The module stand is ready!

Related videos

We suggest watching the video tutorials below on making other options for phone stands.

If you have accumulated unnecessary bank or discount cards, do not rush to throw them away, because they can be used to make useful things - stands for smartphones with different designs. We have collected several design options, including some pretty sophisticated ones.

The first stand is the simplest. It can be done by simply folding the card in two places so that you get something like this:

You can make three bends and get a structure that holds the base of the smartphone more securely.

To prevent the card from breaking and losing its strength at the bending points, it is better to bend it after preheating it with a hairdryer. The plastic will gain increased elasticity for a while, and then harden again.

To create this structure, you need to make cutouts on the map on both sides, forming hooks, and bend it in half. Sharp rags at the places of the cuts need to be grinded off, this can be done with a file or sandpaper, and if they are not there - with a nail file or a clerical knife.

For such a delivery, you will need two cards glued together. This provides additional stability - you can put your smartphone on it not only horizontally, but also vertically.

Two cutouts on the card - and such a stand is ready. For greater stability, you can use two cards - one will be mounted on the left side of the smartphone, the other on the right. The second card can be cut out by putting the first on it, so they will be completely symmetrical and the smartphone will not warp.

The Chinese release such a stand. In terms of its size, it is exactly the same as a bank card, which means that you can make it yourself. To do this, you will need to make several cuts on the card using a highly heated knife and build the same structure by bending the bottom holder, the back for fixing and the base of the card. The advantage of this stand is the ability to adjust the angle of inclination.