Do-it-yourself concrete lamp proportions composition. Concrete lamp. Affordable DIY home decoration option. Concrete and pouring

To make an original lamp with our own hands, we need:

1. Cement + sand.
2. Electric wire and socket
3. Plastic bottle of mineral water for 2 liters and thinner for 1 liter.
4. Tube with thread and nuts. This tube can be purchased from lighting stores, or removed from an old chandelier.
5. Self-tapping screws

First, you need to pick up plastic bottles for mineral water or any other drinks. A 2 liter bottle will serve as the outer shape of the shade, so if the bottle has different embossings, they will be printed on the lamp. A 1 liter bottle must be selected without embossing (smooth), but of such a diameter that an energy-saving lamp can fit inside.

After deciding on the choice, cut off the bottom of the 2 liter bottle.

Drill holes in the covers for the metal tube

Use the nuts to tighten the covers on both sides to hold them in place. The distance between the caps should be two more than the distance between the walls of the bottles.

Use self-tapping screws to secure the shape.

Prepare a grout (ready-mixed cement-sand mixture or cement and sand in a 1: 2 ratio) and fill in the form. Concrete, in consistency, should be thick, then the surface of the lamp will turn out to be smooth. If the solution is more liquid, then many small shells will appear on the walls.

It is worth considering that when the solution is thicker, then it may not fit tightly, and voids will form. Therefore, it is necessary to tamp the solution with a stick after each filling. You can use available vibrating tools (hand massager, etc.). After the solution is poured and tamped, you can unscrew the screws and tamp again carefully so that the center is not disturbed.

After the cement has dried (1 week in the shade), remove the bottles, only proceed carefully as the cement is still fragile and it is easy to damage the face.

Sand all edges of the lamp.

It remains only to connect the socket to the lamp. I want to note that it is very risky to hang a ceiling lamp on a wire, and sooner or later the wire can be transmitted under weight. Therefore, I recommend using a decorative chain for hanging.

Decorative lamp, made by hand, is ready to decorate the interior.

You can make two-color lamps. For this, in different containers are prepared cement mortars made of white and gray cement. After that, they are mixed together for a few seconds (but do not allow mixing until a uniform color), and poured into molds. Additionally, you can use colored dyes for concrete using the marble from concrete technology, and make fancy patterns.

Good luck with your creativity.

Among lovers of DIY crafts, concrete has become a fairly popular material due to its low cost and ease of use. Concrete lamps are very heavy and cold, but this fact does not affect the versatility of such devices, they will perfectly fit into any interior design. To this end, designers create various forms of cement, decorate and paint them in an original way, giving it such shades as gold, silver or copper.

It is worth noting that the concrete lamps made by the hands of designers are very highly rated, so not everyone has the opportunity to acquire such a luxurious product. To save your money, you can create this light source yourself.

Concrete light fixture using package

Before proceeding with the manufacture of this type of lamps, it is necessary to prepare the following materials:

• milk carton. An important condition is that the packaging should not allow moisture to pass through, otherwise the concrete will lose its strength. Than bigger size a lamp is planned, the larger the package should be chosen;
• a plastic bottle into which the light source should then be placed;
• dry mix for concrete.

The first step is to get rid of the bending edges of the package and install a plastic bottle in it. Next, you need to drill holes in the resulting structure. To facilitate this process, it is recommended to pre-make holes in these places using a nail or screwdriver. Then you should fix the bottle with a bolt, passing it through drilled holes and securing.

To preserve the moisture resistance of the packaging, the joints must be treated with a sealant. Thus, we get the base where the concrete will be poured. The dry mixture is diluted with water according to the rules described in the instructions for it. The main thing here is to prevent excess fluid.

The consistency of the finished solution should be similar to shortcrust pastry. Therefore, the water should be poured in gradually, while each particle of the mixture should become wet. After preparation, the concrete should be laid in the previously made form, pressing it tightly enough, thereby excluding the formation empty seats... For complete deaeration of the product, the bag must be thoroughly shaken.

After use, all tools must be washed immediately, otherwise the concrete mixture will set, making its removal almost impossible. After two days (so much is required for the concrete to harden), dispose of the package and unscrew the bolt. To make the concrete luminaire original, it is recommended to make additional holes in it. This will help diffuse the light output. A light source is placed in a plastic bottle, which is then connected to a switch. The finished device can be placed either on the wall or suspended from the ceiling.

Lighting device with bottle application

Pendant lamps made of concrete are no less popular. This device is easily made by yourself. For this purpose, materials such as a sand-cement mixture are used, which contains gravel, water, a network source, an electric cord, self-tapping screws (designed for working with wood), steam plastic bottles (differing in size), bulb holder, as well as additional accessories: knife, drill, threaded tube. The bottles should be prepared first. To do this, you need to cut off their bottom and drill holes for the threaded tube.

The bulb holder is fixed with nuts and self-tapping screws on both sides, so that the base for the lamp is considered to be prepared. The next step involves the preparation of a cement-sand mixture, after which it is necessary to fill the base (using a spoon) for the lamp with it, pressing down a little. This method of concrete placement helps to remove excess air and also ensures an even distribution of the cement.

When the concrete hardens, the plastic is removed with a knife along with self-tapping screws. The uneven surface of the concrete must be sanded with a grain size of 120. The last step is to connect the cord to the light bulb and to the voltage source. Considering the mass of the concrete product, you should make sure that the fastening is strong.

Concrete garden light

Such products fit perfectly into general form garden plots. In addition to their main function of lighting, they serve as a decorative element. Following the recommendations described below, it is quite possible to make these lamps with your own hands. First you need to make the formwork. The material for it is a sheet of plywood, whose thickness is 12 mm.

When creating a form, you should ensure that it can be easily parsed. It is advisable to varnish the details of the base, which will then help to detach it from solid concrete intact. Multiple varnishing will give the finished product a shine and shine. The wiring of a concrete luminaire can be organized using foam or corrugated pipes. The most optimal is the first option, due to which the mass of the luminaire is significantly reduced, and concrete costs are reduced.

Concrete garden lamp

Glue is used to secure the foam. In addition, another advantage is the ease of material removal. In the event that there are fragments left that are difficult to get rid of, it is recommended to use acetone, which completely dissolves the foam. The next step is to create the formwork inside the product. For this purpose, it is possible to use both plywood and cardboard.

The main thing is that their walls have a thickness of at least 25 mm. Also, this formwork should be made in the form of a trapezoid, which will ensure ease of removal. Foam grooves for wiring are laid in the openings. As cement mix both ready-made and self-made are allowed.

When choosing the second option, cement M-500 is used in combination with sand (ratio of one to three). The additive can be gravel or granite chips (one part). By diluting the mixture, it is necessary to achieve the consistency of shortcrust pastry. In the next step, concrete is laid in the formwork. First of all, it is recommended to fill in hard to reach places, and then the rest of the space.

In order for the mixture to lay down more densely, a vibration sander should be used. The product filled with concrete should be covered with plastic wrap for at least three days. This will eliminate the possibility of water leakage from the concrete, as well as give it strength. After the mixture has hardened, the formwork is removed, the lamp is sanded and the lamp is installed.

Such material as concrete today is used not only for construction purposes, but also for interior decoration, representing an original and stylish decoration element. The main advantage of the above-described concrete lamps is not only unusual designbut also simplicity self-made... In addition to lamps, due to the ability of this material to take various forms, various vases, tables and chairs, flower pots are created.

Recently, concrete has become a popular and fashionable addition to the interior. As an element of decor, it entered the design with the loft style in the 50s of the last century. Today, concrete can be used to make tables, dishes, chairs, furniture fronts, sinks and much more. In this article, we will show you how to desk lamp from concrete with your own hands.

What is concrete?

Concrete is an environmentally friendly product that can be recycled and reused. The recipe for making concrete is quite simple. All you need is cement, gravel, sand and water. The exact ratio of all components of the solution is very important, since the strength of future products depends on this. The main component of the concrete mix is \u200b\u200bcement. When choosing its brand, one should determine the level of load and the impact of external destructive factors.

Photo: do-it-yourself concrete lamp

Pay attention to the water that you will add to the concrete mix. If it contains components that violate the structure of concrete, it is better to refuse it. River or lake water is ideal. Speaking about the ratio of proportions, you can see them on the back of the package. Remember that such a ratio is rather arbitrary, therefore, without precise calculations, an unexpected result may turn out.

DIY loft-style concrete lamps at home

To create a DIY concrete lamp at home, it is best to use decorative concrete. The composition of such concrete contains natural components, so it is safe for health. In addition, decorative concrete allows you to simulate various coatings: wood, stone, decorative tiles, brick and much more.

Regardless of which concrete you are using, it is recommended that you sift it before mixing. It is important to use a construction mask to protect the respiratory tract from harmful dust.

What do you need to make a loft lamp with your own hands?

Concrete is great for embodying creative ideas... Despite the coldness of the material, such products bring coziness, warmth and complement any interior style. Also concrete can be combined with other materials. When making a concrete lamp, you can give any color using special dyes for concrete.

The main advantage of concrete is naturalness and environmental friendliness. You can easily make it yourself, without using any special materials, tools and accessories.

How to make a table lamp with your own hands? You will need:

• durable cement-sand mixture;
• drill;
• cord;
• lamp holder;
• threaded tube;
• two plastic bottles of different sizes;
• self-tapping screws for wood.

The first thing to do is prepare the bottles. To do this, cut off the bottom and drill holes in the bottle caps. The size of the hole must be such that a threaded tube can be inserted. Then insert the tube into the holes obtained and fix its position with the nuts. Screw the resulting structure onto the bottles. Use self-tapping screws to stabilize the bottles. In this way, a form is prepared for a concrete lamp.

Now you can start mixing the concrete. The main thing is not to overdo it with water. The mixture should be like cookie dough. Stir it thoroughly so that every grain of the mixture is moist. Remember that all concrete work must be done with gloves, as concrete dries the skin a lot, and concrete dust is not removed from the lungs.

Lay out the resulting concrete. Use a large spoon to fill the mold. Shake and squeeze a little after each spoon to make sure the mixture is evenly distributed. Shake well at the end. This will help remove excess bubbles.

Be sure to wash immediately the dishes in which you mixed the concrete. Otherwise, it will quickly set, and it will be extremely difficult to remove it.

After a couple of days, as soon as the concrete hardens, you can cut off the plastic bottles with a knife and remove the screws. Since the concrete will have a rough shape, it is best to sand its surface with 120 grit sandpaper.

The last step is to connect the cord through a metal tube to the socket and switch. Make sure the lamp is well secured and the mountings can support the significant weight of the concrete.

Glass, concrete and LEDs are combined in this product to create a modern, original and stylish lighting element that will be a great addition to the interior. Details of the process of its manufacture in the given master class.

Materials
To do led lamp do it yourself, prepare:
lED garland;
a cylindrical glass vase 26.5 cm high;
PVC pipe;
concrete mix;
miter saw;
thermo gun and hot glue sticks;
cling film;
electrical tape;
hacksaw;
stationery knife;
drill;
grinder;
plastic bottle;
foamed adhesive tape;
nail;
a piece of plywood or wood board.

Step 1. Cut off PVC pipes a piece about 13 cm high. This will be the mold for the concrete base of your lamp. Adjust its height yourself. The pipe diameter for this project will depend on the diameter of the vase you have taken. You do not need to process the PVC part, it will become outer wall forms for a concrete base.

Step 2. A cylindrical luminaire base with an empty recess inside is to be made of concrete. To make it, you need a small plastic bottle, which must be cut in height about 2 - 3 cm lower than the outer part of the mold.

Step 3. At the top of the concrete base of the lamp, there should be a small rim on which the vase will be mounted. To make it, glue foam tape on the inside of a piece of prepared PVC pipe.

Step 4. Fit the bottom of the form cling film and fix it with electrical tape.

Step 5.Dilute the concrete mix with water in the ratio specified by the mix manufacturer.

Step 6. Place the prepared part of the pipe on a piece of plywood. Place an upside-down, cut and empty plastic bottle right in the center of it.

Step 7.Gradually start pouring concrete mortar into the mold. Periodically knock on the wall of the PVC pipe with a rubber hammer so that parts of the mortar settle to the bottom and do not rise. As the material is poured, the plastic bottle can be pushed upward. Take a nail and lower it to the bottom.

Step 8.Take a sander and use it to vibrate to shrink concrete mortar... During this process, continue to hold the bottle with your nail.

Step 9.Leave the entire structure to dry completely. This process can take several days.

Step 10. Received concrete base for the lamp you need to get it out of the mold. To remove the concrete from the bottom side, gently tap it with a hammer.

It will be easy to remove the mold if you have previously oiled it. If you poured concrete into an unprepared mold, make two small cuts on it with a hacksaw or saw, and remove the PVC part.

Step 11. Sand the resulting workpiece with emery paper or a sander using a 60 grit attachment.

Step 12. Drill a hole at the top to accommodate a wire connected to a plug or other power source. On the bottom side, make a small groove for the wire. This will keep the lamp base stable on a flat surface.

Step 13. Thread the wire through the pre-cut hole and fix it with hot glue.

Step 14.Connect the LED string to the wire. Place it carefully in the vase. To do this, pre-wind the product on any cylindrical object. Cover the concrete base with a makeshift glass jar.

A concrete lamp is a stylish loft accessory that will make an apartment unique, especially if it is handmade. Today, various well-known designer brands offer interesting solutions pendant lights made of concrete. But such items are usually too expensive or difficult to deliver. Therefore, we suggest you make such a loft hanging lamp from concrete with your own hands. All you need for this: two plastic bottles (one large, the other smaller), a liquid mixture of cement with sand and water, a small metal tube with an external thread, four self-tapping screws for wood and electrical wireconnected to a socket and a light bulb. In fact, there is nothing difficult in making a concrete lamp with your own hands. So let's get started.

Step 1. Drill holes in the caps of both plastic bottles with a diameter equal to that of the metal tube.

Step 2. Cut the large plastic bottle in two using a utility knife and scissors. This will be the main shape, the so-called "matrix" for our concrete lamp.

Step 3. Pass the metal tube through both bottle caps. Use the nuts to secure the bottles by screwing them onto the tube.

Step 4. Fix the plastic bottles together using wood screws.

Step 5. Prepare a liquid concrete mixture of the desired consistency.

Step 6. Then pour the prepared cement mixture into the resulting mold from two plastic bottles.

Step 7. After the concrete has hardened, unscrew the fixing screws and remove the excess parts of the plastic mold. Sharp corners can be sanded with sandpaper if desired.

Step 8. Insert the electrical cord into the hole in the metal tube that is fixed to the concrete base.

Step 9. Connect one end of the cord to the bulb holder and the other to the electrical plug.

All. Our stylish concrete lamp is ready.

We also attach a video with detailed description the process of making a luminaire from concrete in English. If you wish, you can experiment with various forms plastic bottles and the composition of the concrete mixture.