A phone stand made of scrap materials. Do-it-yourself stand - how original home-made stands and stops are made (90 photos). Cardboard and plastic cards

Home master having a minimum of tools and maximum diligence, it will not be difficult to make just such a phone stand out of wood. As a material, a 10 mm thick board, plywood is suitable. You can take plastic with a smaller thickness. The approximate dimensions are shown in the figure. The stand is 10 centimeters high and 8 cm wide. (6 cm clean) Installed on two semicircles with a radius of 4 centimeters. Of course, before you get down to business, measure the widest of the phones that will stand in it. A stand for PVC glue is assembled, then decorated at your discretion. For example, in the picture above, the edging is burnished.

Well, here I think I hardly need to explain that, especially to us - people are not young. Yes, many of course found out, the good old "cassette holder" from the audio cassette tape.

We simply remove the cassette, turn the cassette case over, open it to the other side and the stand is obtained at an angle of about 75 degrees. The width of the "pocket" is about 12 millimeters, the current not thick smartphone fits there perfectly.

Here is such a "brutal" phone stand made of an ordinary aluminum plug. The two outer teeth are bent at the very base at an angle of 90 degrees. The two middle antennae are bent at a distance of 15 millimeters from the base, also at an angle of 90 degrees. Your gadget is embedded between them. The fork handle acts as a support.

This stand requires six clothespins and one pencil. The pencil, preferably hexagonal, will slide on the round clothespins. I think it's clear from the photo - four clothespins are legs, two on the top actually hold the gadget, the phone is inserted between their petals. The width adjustment is quite large - for the length of the pencil. By the way, even if you hook a pair of clothespins on the edge of any vertical surface (let's say the wall of a box), they will successfully cope without four other clothespins and a pencil!

This stand is very simple, but also suitable for small phones. This is an ordinary old bank or discount plastic card. It should be divided across into three equal parts with a pencil and bent along the lines. But I would make the lower "heel" on which the phone will stand, I would make only a centimeter, and divide the remaining distance into the "shoulder" of the support and support itself.

It is impossible to imagine a person who would not have a mobile ...

Now it is almost impossible to imagine a person who would not have such a technical device as a mobile phone.

With the invention of this technique, life has become much easier: if you need to make an urgent call, the phone is always with you, besides it, it is also much easier to find someone ... In general, it makes no sense to describe all the advantages of a mobile phone, since they are really obvious and do not need advertising.

However, today, when we talk about mobile phones, we most often mean modern smartphones, which, in addition to ordinary calls, are capable of performing a lot different functions... A modern phone can instantly access the Internet and find the information you need, receive and send emails, take stunning photos and videos of great quality, etc. That is why we most often use the phone not as a means of communication, but also as a multifunctional gadget.

It is for this reason that you always want your phone to be always at hand, in the field of maximum availability. In addition, sometimes you need to view photos or videos on your phone, so you want it to be located in the most convenient way for this.

In order to satisfy all these needs, you must, of course, use mobile phone stand... Today in stores you can find a lot of accessories of various shapes. So, for example, many probably remember the popular phone stands in the form of a woman's hand a few years ago. Nowadays, the stands have become not only more attractive and elegant, but also functional. They are capable of charging the phone's battery, informing about a call, tilting the phone for viewing from a variety of angles, etc. So everyone, even the most discerning and demanding consumer, can always buy a product to their liking.

DIY mobile phone stand

However, if you prefer things made with my own hands, which will be a real exclusive, we will tell you how you can independently make an attractive phone stand... To do this, there are many different ways, but we will tell you about the simplest, and at the same time, unusual.

DIY mobile phone stand - 1

The first option is perfect for a phone with a wide display and a fairly long body, such as an iPhone or any phone from the Samsung line. The stand is incredibly comfortable to use and truly functional. To make it you will need only 2 minutes of your time.

1. You need a binder (a kind of clip that is used to hold papers together), as well as a suction cup, which is used to attach, for example, towel holders. So, attach the binder to the suction cup where the hook is. Voila! Simple and comfortable stand ready.
2. Attach the suction cup to the back of the phone (don't be afraid, it won't damage it and leave no traces when detached) and position the phone as you like, vertically or horizontally, in any case the viewing angle will be ideal.

DIY mobile phone stand - 2

The second option is suitable for truly creative people. In order to do it, you need to master the art of origami.

1. To make such a stand, you need to make 24 white check marks and 23 pink ones. Check marks are made in the same way as cranes.
2. Then the white check marks are fastened in a circle so that, as a result, a kind of circle is formed. Insert one pink checkmark between each pair. Thus, you get a tapering cone.
3. Continue construction to the desired height. Place your mobile phone in the center, and feel free to admire the creation of your own hands!

Stand- useful and convenient thing at home. For example, phones or tablets that have become an integral part of our daily life are a little inconvenient to use in stationary conditions. If you do not have a branded or suitable case that can secure the gadget in an inclined position, then you will have to hold it with your hands. This is inconvenient when watching a movie for a long time, while eating or reading for a long time.

The best solution to this problem may be to buy a specially designed stand. But, sometimes, we need it right now, or we simply feel sorry for the money for a seemingly temporary thing. In this case, you can make the stand yourself from available tools. It does not take a lot of time! A couple of minutes and you can comfortably sit in front of the screen of your gadget, while freeing your hands.

In this article, we will rely primarily on the options for phone stands, but they can also be slightly modernized and used for tablets, books, even pictures or plates. It all depends only on your imagination. But if she is sleeping, then there is nothing wrong with that. The options proposed in the article have been analyzed in detail, and it will not be difficult for you to slightly increase the dimensions specifically for the thing for which you are making a stand.

Materials at hand to help

You can make a stand yourself from scrap materials. For this, almost any material that you have at home will do. This could be:

• wire
• cardboard
• cardboard box
• fabric and padding
• bottle
• tree
• paper
• the pencils
• constructor
• stationery holders
• unnecessary plastic cards
• old cassette player

Only fantasy can limit you in your choice. Of course, the stores offer a huge selection of products in this category. Nevertheless, making the holder yourself has a number of indisputable advantages:

• Rapidity. Sometimes a stand is needed as soon as possible, and there is no time to go to the store to buy it.
• Inexpensive or free. You can make a holder from what you already have in your home.
• Originality. With your own hands, you will create a truly unique product.

Pencil phone stand

In order to assemble this structure, you will need:

• 6 pencils
• 4 stationery rubber bands

Despite the intricate appearance, this construction is very easy to assemble. The bottom line is that two pencils at the ends are held together with an elastic band, and a third pencil is pushed between the turns of the elastic band. The result is a geometric figure - a tetrahedron. If you still have questions about how to make this version of the stand, then use the example below.

The figure clearly shows how the pencils are held together.

Use pencils with erasers at the ends to avoid slipping and give the stand more stability.

Phone stand made of paper clips

The most economical and simple stand option, to create which you only need a paper clip.

To do this, you need to bend it into the same shape as in the figure.

This design will hold the phone in place without any problems.

Phone stand made of a plastic card

Any unnecessary plastic card will do for this. Just bend it along the short side, stepping back about 1 cm from the edge, and bend the rest in the opposite direction exactly in half. You will get as shown in the picture.

Cardboard stand for phone or tablet

Cardboard- an excellent material that is widely used for various homemade "stuff". Probably, many people at home have a cardboard box or an unnecessary sheet of cardboard. It is worth trying to use it to create a stand as well.

For this you need:

• cardboard
• scissors

From a sheet of cardboard folded in half, cut a 10 x 10 cm strip. Then draw the figure shown in the figure on it and cut it along the contour.

You will have a comfortable and stable stand that you can carry with you.

This holder option can be used for a tablet or book. The essence of manufacturing is the same, only you need to fit the part to the size of your gadget, as shown in the figure.

It is necessary to use well bending cardboard so that the stand does not "open".

It is important to understand that a cardboard stand is not necessarily a sloppy design. brown... It can be stylish, comfortable and beautiful. You just need to change the shape a little and the result will change dramatically.

Origami paper phone stand

Perhaps you don't have cardboard at home, but you have thick paper. It is also suitable for making a stand! All you need is paper and scissors. Cut out the shape according to the diagram below, and then fold along the fold lines.

That's all. The origami stand is ready to use.

Wire stand for phone or tablet

One of budget optionsmade from scrap materials.

During work you will need:

• wire 2-3 mm thick
• pliers
• wire cutters to cut the wire

Everything is done as simply as possible: in the right places, the wire is bent so that it becomes a holder.

To make the design more stable, the wire can be connected with a rubber band.

Such a stand can become real design solution: It can be painted in a different color and it will be completely transformed, or you can fill the "voids" with decorative wire curls. This design is suitable for both a phone and a tablet, the only difference is in the size of your gadget.

Unusual Lego phone stand

Probably, this version of the stand will especially appeal to teenagers and men. Here you can show your imagination by creating a whole complex for your smartphone with the ability to change the position, and maybe even with the amplification of the speaker sound, or you can do with a minimum of details. The creative process is not only enjoyable, but also beneficial.

To make such a design, you will need a few parts and a base. The tilt level can be changed by adding or removing details. And the position of the gadget is easy to change, also adjusting the design.

A phone stand from an old cassette holder

Perhaps an old cassette player was lying around at someone's house. It is unlikely that it will ever be useful, and no one uses cassettes with the advent of disks and electronic media. But still, you can find a use for the cover in which the cassette was located.

To do this, it is enough to "turn" the cassette to the inside out by folding the cover back. You can place a telephone in the hole in which the cassette was held. One of the advantages of this design is that it is easy to clean and transparent.

Plastic bottle phone stand

Many of us travel or travel on the train for business. Oftentimes, on trains, there is nothing near the power outlets where you can safely place your phone. Nevertheless, the gadget is discharged and needs to be charged. You can simplify this task with a stand made from a bottle. Its essence lies in the fact that the gadget is placed in the cut-off bottom of the bottle, which remains hanging on the plug from the charging device. Thus, there is no need to stand nearby and hold the phone in your hands or look for a way to fix it.

To make such a stand-holder, you will need:

• plastic bottle for shampoo or drink
• scissors

First, wash the bottle to remove any cosmetic or soda residue. Then, mark it up. The back wall of the stand should become a kind of handle on which the phone holder will hang. The front wall should be high enough so that the phone does not fall out over the edge. The next step is to cut the stand around the office.

For this, it will be more convenient to use a sharp stationery knife.

Cut a hole at the top of the handle so that it can be attached to the fork charger... You can decorate the stand for every taste: using adhesive paper, paints or stickers.

Wooden phone or tablet stand

If you want to do original standthen one of good materials for its manufacture can be called a tree. Such a stand will be strong, durable, and can also serve as a good gift for a loved one. It is important to understand that working with wood requires some minimum skill and special tools.

In the process of work, in addition to a wooden block, you may need materials such as:

• jigsaw
• sandpaper
• wood cutting knives

Be careful and attentive when working with such tools.

Stand manufacturing steps:

• Work the block of wood by sawing off excess parts and making a groove in the top center for your phone or tablet.
• Using sandpaper, remove all roughness and splinters from the surface of the future holder.
• You can cover the finished product with varnish or special paint.

Another option for a wooden stand for a phone or tablet is an analogue of its cardboard version. In this case, instead of a wooden block, it is better to use plywood.

To do this, make a stencil of the "legs" of the holder and a crossbar that will hold them together. And transfer it to plywood. Carefully cut with a jigsaw and smooth out any unevenness and roughness with sandpaper. Using super glue, connect the legs and the bar.

DIY stand case for phone or tablet

The most popular gadget stand is the stand case. You will have to tinker a little with it, but the result is worth it. This option is convenient to take with you when traveling, it is durable and can protect the screen.

To make such a holder, you will need:

• facing material, it is best to choose leather
• material for inner cladding
• plain and thick cardboard or rigid material
• elastic for fasteners
• pencil
• ruler
• scissors
• double sided tape

How to do it?

• Cut the cardboard to fit the size of the tablet, so that it completely covers it. This is the future base, the dimensions of which will be the base for all elements.
• Make a few folds so that the front of the case should bend to support the tablet.
• Now we take a hard material, which will give the case stability. Cut it off so that it follows the contour of the workpiece.
• We apply it to the base and make the edging so that it does not interfere with the folds.

• From the inside, we process the cover with soft materials, gluing it to the base blank with double-sided tape.
• The next step is to mount the tablet itself. To do this, we make small holes in the rigid elements for the rubber bands, which will hold the tablet.

• From the outside we glue the finishing material.

Do this as carefully as possible. The appearance of the product will depend on this.

That's all. The stand is ready! It is convenient and can be used not only as a holder, but also to protect the screen.

Stand-pouch for a tablet or phone

An original and cute version of the gadget stand. It is suitable for girls and can be a cute home accessory.

For manufacturing you will need:

• scissors
• the cloth
• padding material
• thick cardboard
• thread and needle
• button

Manufacturing process:

• First you need to cut out a template from the cardboard to fit your gadget.
• Then, from the fabric, cut a rectangle twice the size of the resulting pattern.
• Fold the fabric base in half and mark with stitches a fold 10 cm from the edge.
• Sew the bag, leaving one side not swept.
• After turning the bag inside out, position it so that the seam runs in the middle, and at the end you get a diamond. After ironing it with an iron, bend the top corner of the diamond so that it is in the middle and sew. This is shown in more detail in the figure.

• Then insert cardboard into the product and fill the remaining space with padding.
• Make a seam along the very edge of the template. Fold up the edges of the unsewn side and carefully stitch it, leaving a hole for the stuffing.
• Make a roller and sew the hole.

That's all. The product is ready. You can decorate it to your liking, giving it even more charm!

Phone stand made of stationery clips

Another interesting and at the same time very simple option. If you have several stationery clips at home, feel free to use them!

You will need 2 clamps, one larger and one smaller. By connecting them together as shown in the figure, in a couple of seconds you will receive a holder for the phone.

It can also be done with two clips of the same size.

Phone stand from unnecessary CD-ROM

An unnecessary CD can serve as a stand for your phone. In order to make such a holder, you will need a little time and work with temperature. So be careful!

Conclusion

For a creative person, all boundaries are erased. And he can create any object with his own hands from scrap materials. For the stand, you can use options such as an ordinary office business card holder, or a stand for books well known to all of us since school days, even a toilet paper sleeve can be an excellent option for a holder.

There are many opportunities for creativity, you just need to look around carefully. Maybe you can make the most unusual smartphone accessory with your own hands!

If you have accumulated unnecessary bank or discount cards, do not rush to throw them away, because they can be used to make useful things - stands for smartphones with different designs. We have collected several design options, including some pretty sophisticated ones.

The first stand is the simplest. It can be done by simply folding the card in two places so that you get something like this:

You can make three bends and get a structure that more securely holds the base of the smartphone.

To prevent the card from breaking and losing its strength at the bending points, it is better to bend it after preheating it with a hairdryer. The plastic will gain increased elasticity for a while, and then harden again.

To create this structure, you need to make cutouts on the map on both sides, forming hooks, and bend it in half. Sharp rags at the places of the cuts must be grinded off, this can be done with a file or sandpaper, and if they are not there - with a nail file or a clerical knife.

For such a delivery, you will need two cards glued together. This provides additional stability - you can put your smartphone on it not only horizontally, but also vertically.

Two cutouts on the card - and such a stand is ready. For greater stability, you can use two cards - one will be mounted on the left side of the smartphone, the other on the right. The second card can be cut out by putting the first on it, so they will be completely symmetrical and the smartphone will not warp.

The Chinese release such a stand. In terms of its size, it is exactly the same as a bank card, which means that you can make it yourself. To do this, you will need to make several cuts on the card using a highly heated knife and build the same structure by bending the bottom holder, the back for fixing and the base of the card. The advantage of this stand is the ability to adjust the angle of inclination.

Mobile phones are tightly embedded in our daily life... Even children already use them from the very first grades of school. In order not to throw your gadget just on the table, let's consider how to make a phone stand from scrap materials.

First option: from binders

Let's figure out how to make a do-it-yourself phone stand from what is in almost every home. There are quite a few ways. In this workshop, we will make it from binders (paper clips).

This model is well suited for widescreen phones. It will turn out to be very convenient and practical, and it will take literally two minutes to create.

To work, you need binders and a suction cup.

Manufacturing procedure:

1. Connect the binder to the suction cup (a towel holder will do as well) where the hook is.
2. Attach the back of your phone to this suction cup when you need to put it down, and you're done.

The advantage of this type is that the phone can be positioned in any position, both horizontally and vertically, or at an angle.

Second option: from paper

When there are a lot of pieces of paper at hand different colorsthen the modular origami technique comes to mind. Let's figure out how to make a phone stand out of paper.

To work, you need 24 white checkmarks and 23 pink ones. Check marks are the simplest element of modular origami.

To make modules, follow these steps:

1. The triangular module is folded from rectangles so that they turn out to be the same size, take an A4 sheet and cut it into 16 or 32 small rectangles.
2. Fold the rectangle in half.
3. And again in half, then unfold to form a fold line in the middle.
4. Bend the edges of the rectangle to this line, and those where the first fold line goes.
5. From below you have a ledge, bend its corners up to the edge of the first part.
6. Now bend the rest of the lower canvas upwards to form an even triangle on the back side.
7. Fold it in half. And you will see that you have pockets on both sides.

Now we turn to our question on how to make a phone stand from the following modules:

• Fasten the white check marks in a circle.
• Then place the pink ones between each pair. This will create a tapering cone.
• Continue assembling the structure to the desired height and you're done.

This method is suitable for those who like to work with paper using the modular origami technique, if you are more fond of cutting and pasting everything, then pay attention to the following model.

The third option: from a bottle of shampoo

How to make a do-it-yourself phone stand from a shampoo bottle? The work will turn out to be very stylish, despite the simple materials, it will look expensive, as if purchased.

Manufacturing progress:

1. Find the right sized shampoo bottle.
2. Make a line in the middle and cut along it. For convenience, it is better to do not straight, but leave a ledge with a slot on the back side, so that you can not only install the stand on the table, but also hang it on the wall.
3. Take a nice ornamental paper (you can use wrapping paper), wrap it around the stand and glue it.
4. Carefully trim the excess wrapper around the outline. Your work is ready.

This craft will look great in your home, especially if you choose the right color and pattern for the wrapping paper. You can independently come up with a form for such work or make it according to a sample. This was one of many ways to make a phone stand.

The fourth option: from popsicle sticks

One of the most original optionsHow to make a phone stand is using popsicle sticks. To do this, ask your friends and relatives in advance not to throw out such sticks.

When you collect enough, you will need to glue them together:

• make the bottom first;
• then the backrest along the height of the phone;
• the side ones will look good at an angle.

You can connect the parts not only with glue, but also by gluing a transverse stick for greater strength.

There are many ways to make a phone stand out of scrap materials. We have covered only a few of them. It all depends on your mood and imagination. Even from the old Lego constructor, you can make a wonderful option or sew a wonderful wall cover from dense fabric.

Use any idea. Enjoy your creativity!