Stand for the phone from improvised materials. Do-it-yourself stand - how original home-made coasters and stops are made (90 photos). Cardboard and plastic cards

Home master having a minimum of tools and a maximum of diligence, it will not be difficult to make just such a wooden phone stand. As a material, a board 10 mm thick, plywood, is suitable. You can also use thinner plastic. Approximate dimensions are shown in the figure. The stand is 10 centimeters high, 8 cm wide (6 cm clean). Installed on two semicircles with a radius of 4 centimeters. Of course, before you get down to business, measure the widest of the phones that will stand in it. A stand is assembled for PVC glue, then decorated at your discretion. For example, in the figure above, the edging is processed by burning.

Well, here I think it’s hardly necessary to explain anything, especially to us - people who are not young. Yes, of course, many have learned, the good old "cassette" from a tape cassette.

Just remove the cassette, turn the cassette holder over, open it to the other side and you get a stand at an angle of about 75 degrees. The width of the "pocket" is about 12 millimeters, the current thin smartphone fits perfectly there.

Here is such a "brutal" stand for the phone from an ordinary aluminum plug. The two extreme teeth are bent at the very base at an angle of 90 degrees. The two middle tendrils are bent at a distance of 15 millimeters from the base, also at an angle of 90 degrees. Your gadget is inserted between them. The fork handle plays the role of a support.

This coaster requires six clothespins and one pencil. The pencil is preferably hexagonal, on a round clothespins will slide. I think it’s clear from the photo - four clothespins are legs, two on the top actually hold the gadget, a phone is inserted between their petals. The width adjustment is very large - the length of the pencil. By the way, even if you hook a couple of clothespins on the edge of any vertical surface (let's say the wall of the box), they will successfully cope without four other clothespins and a pencil!

This stand is very simple, but also suitable for small phones. This is an ordinary old bank or discount plastic card. It should be divided across into three equal parts with a pencil and bent along the lines. But I would make the lower "heel" on which the phone will stand only a centimeter, and divide the remaining distance into the "shoulder" of the prop and support itself.

It is impossible to imagine a person who would not have a mobile ...

Now it is almost impossible to imagine a person who would not have such technical device like a mobile phone.

With the invention of this technique, life has been greatly simplified: if you need to call urgently, the phone is always with you, besides this, it is also much easier to find someone ... In general, it makes no sense to describe all the advantages of a mobile phone, since they are really obvious and do not need advertising.

However, today, when we talk about mobile phones, we most often mean modern smartphones, which, in addition to ordinary calls, are capable of performing a lot of various functions. A modern phone is able to instantly access the Internet and find the necessary information there, receive and send letters via e-mail, take amazing photos and video clips of great quality, etc. That is why we most often use the phone not as a means of communication, but also as a multifunctional gadget.

It is for this reason that you always want your phone to be always at hand, in the field of maximum availability. In addition, sometimes you need to view photos or videos on your phone, so you want it to be located in the most convenient way for this.

In order to satisfy all these needs, one must, of course, use mobile phone stand. Today in stores you can find a lot of different shapes of accessories. So, for example, many people probably remember the phone holders in the form of a female hand that were popular a few years ago. Nowadays, coasters have become not only more attractive and elegant, but also functional. They are able to charge the phone's battery, report a call, tilt the phone to view from a variety of angles, etc. So everyone, even the most demanding and demanding consumer, will always be able to purchase a product to their liking.

DIY mobile phone stand

However, if you prefer things made with my own hands, which will be a real exclusive, we will tell you how you can make an attractive phone stand. There are many different ways to do this, but we will talk about the simplest, and at the same time unusual.

DIY mobile phone stand - 1

The first option is perfect for a phone with a wide display and a fairly long body, such as an iPhone or any phone from the Samsung line. The stand is incredibly comfortable to use and really functional. It only takes 2 minutes of your time to make it.

1. You need a binder (a kind of clip that is used to fasten papers together), as well as a suction cup, which is used to attach, for example, towel holders. So, attach the binder to the suction cup in the place where it has a hook. Voila! Simple and convenient stand ready.
2. Attach the suction cup to the back of your phone (don't worry, it won't damage it and won't leave marks when you remove it) and position your phone however you like, vertically or horizontally, either way the viewing angle will be perfect.

DIY mobile phone stand - 2

The second option is suitable for truly creative natures. In order to make it, you need to master the art of origami.

1. To make such a stand, you need to make 24 white checkmarks and 23 pink ones. Check marks are made in the same way as cranes.
2. Then the white checkmarks are fastened in a circle so that a kind of circle eventually forms. Insert one pink tick between each pair. Thus, you get a cone tapering upwards.
3. Continue the construction to the desired height. Place a mobile phone in the center, and boldly admire the creation of your own hands!

Stand- useful and handy thing at home. For example, phones or tablets, which have become an integral part of our daily lives, are a little inconvenient to use in stationary conditions. If you do not have a branded or suitable case that can secure the gadget in an inclined position, then you will have to hold it with your hands. This is inconvenient when watching a movie for a long time, while eating or reading for a long time.

The best solution to this problem may be to purchase a stand specially designed for this. But, sometimes, we need it right now, or we simply feel sorry for the money for a seemingly temporary thing. In this case, you can make a stand yourself from improvised means. It does not take a lot of time! A couple of minutes and you can comfortably sit in front of the screen of your gadget, while freeing your hands.

In this article, we will primarily rely on phone stand options, but they can also be slightly upgraded and used for tablets, books, even pictures or plates. It all depends on your imagination. But if she sleeps, then there is nothing wrong with that. The options proposed in the article are analyzed in detail, and it will not be difficult for you to slightly increase the dimensions specifically for the thing for which you are making a stand.

Handy materials to help

You can make a stand yourself from improvised materials. Almost any material that you have at home is suitable for this. It could be:

• wire
• cardboard
• cardboard box
• fabric and padding
• bottle
• tree
• paper
• pencils
• constructor
• stationery holders
• unnecessary plastic cards
• old cassette

Only your imagination can limit your choice. Of course, the stores offer a huge selection of products in this category. However, making the holder yourself has a number of undeniable advantages:

• Rapidity. Sometimes a stand is needed as soon as possible, and there is no time to go to the store to buy it.
• Cheap or free. You can make a holder from what you already have in your home.
• Originality. With your own hands you will create a truly unique product.

Pencil phone stand

In order to assemble this design, you will need:

• 6 pencils
• 4 rubber bands

Despite the intricate appearance, this design is very easy to assemble. The bottom line is that two pencils are fastened at the ends with an elastic band, and the third pencil is pushed between the turns of the elastic band. In the end it will geometric figure- tetrahedron. If you still have questions about how to make this version of the stand, then use the example below.

The figure clearly shows how the pencils are held together.

To avoid slipping and to make the stand more stable, use pencils with erasers on the ends.

Paper clip phone stand

The most economical and simple version of the stand, to create which you only need a paper clip.

To do this, you need to bend it into the same shape as in the figure.

This design will hold the phone without any problems.

Plastic card phone holder

For this, any unnecessary plastic card will do. Just fold it along the short side, stepping back from the edge about 1 cm, and bend the rest in the opposite direction exactly in half. You will get it as shown in the picture.

Stand for phone or tablet made of cardboard

Cardboard- an excellent material that is widely used for various homemade "things". Probably, many people have a cardboard box or an unnecessary sheet of cardboard at home. It is worth trying to use it to create a stand.

For this you will need:

• cardboard
• scissors

From a sheet of cardboard folded in half, cut a strip measuring 10 by 10 cm. Then draw the figure shown in the figure on it and cut it out along the contour.

You will get a comfortable and stable stand that you can carry with you.

This holder option can be used for a tablet or a book. The essence of manufacturing is the same, only it is necessary to fit the part to the size of your gadget, as shown in the figure.

It is necessary to use well-flexible cardboard so that the stand does not "open".

It is important to understand that a cardboard stand is not necessarily a sloppy design. Brown. It can be stylish, comfortable and beautiful. You just need to change the shape a little and the result will change dramatically.

Origami paper phone stand

Perhaps you do not have cardboard at home, but there is thick paper. It is also suitable for making a stand! All you need is paper and scissors. Cut out the shape as shown below, then fold along the fold lines.

That's all. The origami stand is ready to use.

Wire stand for phone or tablet

One of budget options made from scrap materials.

During work you will need:

• wire 2-3 mm thick
• pliers
• wire cutters to cut the wire

Everything is done as simply as possible: in the right places, the wire is bent so that a holder is made from it.

To make the design more stable, the wire can be connected with a rubber band.

Such a stand can become a real design solution: it can be painted in a different color and it will completely change, or you can fill in the "voids" with decorative wire curls. This design is suitable for both phone and tablet, the difference is only in the size of your gadget.

Unusual phone stand from Lego

Probably, this version of the stand will especially appeal to teenagers and men. Here you can show your imagination by creating a whole complex for your smartphone with the ability to change position, and maybe even amplify the sound of the speaker, or get by with a minimum of details. The creative process will not only bring pleasure, but also benefit.

To make such a design, you will need a few parts and a base. The tilt level can be changed by adding or removing details. And the position of the gadget is easy to change, just adjusting the design.

Phone stand from an old cassette

Perhaps someone has an old cassette player lying around at home. It is unlikely that it will ever come in handy, and with the advent of disks and electronic media, no one uses cassettes anymore. But still, you can find a use for the cover in which the cassette was located.

To do this, it is enough to "turn" the cassette player inside out by folding the cover back. You can put a phone in the hole where the cassette was held. One of the advantages of this design is that it is easy to wash and it is transparent.

Plastic bottle phone stand

Many of us go on a trip or travel on business by train. Often, on trains, there is nothing near the sockets where a phone could be securely placed. However, the gadget is discharged and needs to be charged. You can simplify this task with a stand made from a bottle. Its essence lies in the fact that the gadget is placed in the cut off bottom of the bottle, which remains hanging on the plug from the charging device. Thus, you do not need to stand nearby and hold the phone in your hands or look for a way to secure it.

To make this holder you will need:

• plastic bottle for shampoo or drink
• scissors

First, wash the bottle to remove any cosmetic or soda residue. Then, mark it up. The back wall of the stand should become a kind of handle on which the phone holder will hang. The front wall should be high enough so that the phone does not fall out over the edge. The next step is to cut the stand around the office.

To do this, it will be more convenient to use a sharp clerical knife.

Cut a hole in the top of the handle so that it can be attached to the fork charger. You can decorate the stand for every taste: with adhesive paper, paints or stickers.

Wooden phone or tablet stand

If you want to do original stand, then one of good materials for its manufacture, you can call a tree. Such a stand will be strong, durable, and can also serve as a good gift for a loved one. It is important to understand that working with wood requires some minimal skills and special tools.

In the process of work, in addition to a wooden block, you may need materials such as:

• jigsaw
• sandpaper
• wood cutting knives

Be careful and attentive while working with such tools.

Stand manufacturing steps:

• Process the wooden block by sawing off the excess parts and making a recess in the top middle for a phone or tablet.
• Using sandpaper, remove all roughness and splinters from the surface of the future holder.
• You can cover the finished product with varnish or special paint.

Another option for a wooden stand for a phone or tablet can be called an analogue of its cardboard version. In this case, instead of a wooden block, it is better to use plywood.

To do this, make a template for the "legs" of the holder and a crossbar that will fasten them together. And transfer it to plywood. Carefully cut out with a jigsaw and smooth out irregularities and roughness with sandpaper. Using super glue, connect the legs and the crossbar.

DIY stand case for phone or tablet

The most popular option for a gadget stand is a stand case. It will take a little fiddling with it, but the result is worth it. This option is convenient to take with you when traveling, it is durable and can protect the screen.

To make this holder you will need:

• cladding material, it is best to choose leather
• material for inner cladding
• simple and thick cardboard or rigid material
• rubber band for fastening
• pencil
• ruler
• scissors
• double sided tape

How to do it?

• Cut the cardboard according to the size of the tablet, so that it completely covers it. This is the future base, the dimensions of which will be the base for all elements.
• Make a few folds in the way that the front of the case will then need to bend to support the tablet.
• Now we take a hard material, which will give the case stability. Cut it so that it follows the contour of the workpiece.
• We apply to the base and make a border, so that it does not interfere with the folds.

• From the inside, we process the cover with soft materials, gluing it to the base blank with double-sided tape.
• The next step is fasteners for the tablet itself. To do this, we make small holes in the hard elements for rubber bands, which will hold the tablet.

• From the outside we glue the finishing material.

Do this as carefully as possible. The appearance of the product will depend on this.

That's all. The stand is ready! It is convenient and can be used not only as a holder, but also to protect the screen.

Pouch for tablet or phone

An original and cute version of the stand for the gadget. It is suitable for girls and can become a cute home accessory.

For manufacturing you will need:

• scissors
• textile
• stuffing material
• thick cardboard
• thread and needle
• button

Manufacturing process:

• First you need to cut out a template from cardboard according to the size of your gadget.
• Then cut a rectangle out of the fabric twice the size of the resulting template.
• Fold the base of the fabric in half and mark the crease with stitches 10 cm from the edge.
• Sew the bag, leaving one side unswept.
• After turning the bag inside out, position it so that the seam runs through the middle, and at the end you get a rhombus. After ironing it, bend the upper corner of the rhombus so that it is in the middle and sew. This is shown in more detail in the figure.

• Then insert cardboard into the product and fill the remaining space with stuffing material.
• Make a seam along the very edge of the template. After folding the edges of the unsewn side, carefully stitch it, leaving an opening for stuffing.
• Make a roll and sew up the hole.

That's all. The product is ready. You can decorate it to your taste, giving it even more charm!

Phone holder made of stationery clips

Another interesting and at the same time very simple option. If you have a few stationery clips at home, feel free to use them!

You will need 2 clips: one larger and one smaller. By connecting them together as shown in the figure, in a couple of seconds you will get a holder for the phone.

It can also be done with two clips of the same size.

Stand for phone from an unnecessary CD-disk

An unnecessary CD-ROM can serve as a stand for the phone. In order to make such a holder, you will need a little time and work with temperature. So be careful!

Conclusion

For a creative person, all boundaries are erased. And he can create any object with his own hands from improvised materials. For the stand, you can use options such as an ordinary office business card holder, or a book stand well known to all of us since school days, even a toilet paper sleeve can be an excellent holder option.

There are many opportunities for creativity, you just need to carefully look around. Maybe you will make the most unusual smartphone accessory with your own hands!

If you have accumulated unnecessary bank or discount cards, do not rush to throw them away, because you can make useful things out of them - smartphone stands with different designs. We have collected several design options, including quite sophisticated ones.

The first stand is the easiest. It can be done by simply bending the card in two places so that you get something like this:

You can make three bends and get a design that more securely holds the base of the smartphone.

In order to prevent the card from breaking and losing strength at the bending points, it is better to bend it after preheating it with a hair dryer. Plastic will take some time increased elasticity and then hardens again.

To create this design, you will need to make cutouts on the map on both sides, forming hooks, and bend it in half. Sharp tatters at the sites of cuts need to be ground off, this can be done with a file or sandpaper, and if they are not there, with a nail file or a clerical knife.

For such a delivery, two cards glued together are required. This provides additional stability - you can put your smartphone on it not only horizontally, but also vertically.

Two cutouts on the map - and such a stand is ready. For greater stability, you can use two cards - one will be attached to the left side of the smartphone, the other to the right. The second card can be cut out by putting the first one on it, so they will be completely symmetrical and the smartphone will not warp.

The Chinese produce such a stand. It is exactly the same size as bank card which means you can do it yourself. To do this, you need to make several cuts on the card with a very heated knife and build the same structure by bending the lower holder, the back for fixing and the base of the card. The advantage of this stand is the ability to adjust the angle of inclination.

Mobile phones have firmly entered our everyday life. Even children already use them from the very first grades of school. In order not to leave your gadget just on the table, consider how to make a phone stand from improvised materials.

First option: from binders

Let's figure out how to make a phone stand with your own hands from what is in almost every home. There are quite a few ways. In this master class, we will make it from binders (paper clips).

This model is well suited for widescreen phones. It will turn out to be very convenient and practical, and it will take literally two minutes to create.

To work, you will need binders and a suction cup.

Production order:

1. Connect the binder to the suction cup (a towel holder will work too) in the place where the hook is located.
2. Attach the back of your phone to this suction cup when you need to put it down and you're done.

The advantage of this type is that you can place the phone in any position, both horizontally and vertically, or at an angle.

Second option: paper

When there are a lot of papers at hand different colors, then the modular origami technique comes to mind. Let's figure out how to make a phone stand out of paper.

To work, you need 24 white checkmarks and 23 pink ones. Check marks are the simplest element of modular origami.

To make modules, do the following:

1. The triangular module is made up of rectangles to make them the same size, take an A4 sheet and cut it into 16 or 32 small rectangles.
2. Fold the rectangle in half.
3. And again in half, then unfold to make a fold line in the middle.
4. Bend the edges of the rectangle to this line, and those where the first fold line goes.
5. From below you have formed a ledge, bend its corners up to the edge of the first part.
6. Now bend the entire remaining lower canvas up to get an even triangle on the back side.
7. Fold it in half. And you will see that you have pockets on both sides.

Now let's move on to our question, how to make a phone stand from such modules:

• Fasten white checkmarks in a circle.
• Then place pink ones between each pair. So you get a cone tapering upward.
• Continue assembling the structure to the desired height and you're done.

This method is suitable for those who like to work with paper using the modular origami technique, if you like to cut and paste everything more, then pay attention to the following model.

Third option: from a shampoo bottle

How to make a DIY phone stand from a shampoo bottle? The work will turn out to be very stylish, despite the simple materials, it will look expensive, as if purchased.

Manufacturing progress:

1. Choose the right size shampoo bottle.
2. Make a line in the middle and cut along it. For convenience, it is better not to do it straight, but to leave a protrusion with a slot on the back side, so that you can not only install the stand on the table, but also hang it on the wall.
3. Take beautiful paper with an ornament (you can use wrapping paper), wrap the stand with it and glue it.
4. Carefully cut off the excess wrapper around the outline. Your work is ready.

This craft will look great in your home, especially if you choose the right color and pattern for wrapping paper. You can independently come up with a form for such work or make according to the model. This was one of the many ways to make a phone stand.

Fourth option: from popsicle sticks

One of the most original variants how to make a phone stand is to use popsicle sticks. To do this, ask friends and relatives in advance not to throw out such sticks.

When you collect enough, they will need to be glued together:

• first make the bottom;
• then the backrest to the height of the phone;
• the side ones will look good when tilted.

You can connect parts not only with glue, but also by gluing a transverse stick for greater strength.

There are many ways to make a phone stand from scrap materials. We have considered only a few of them. It all depends on your mood and imagination. Even from the old designer "Lego" you can make great option or sew a wonderful cover on the wall from dense fabric.

Use any idea. Enjoy your creativity!