DIY wooden bar stool. How to make a bar stool with your own hands? Folding bar stool made of wood

If the area of ​​​​your apartment or house allows, then you can ennoble the rooms of the dwelling to your liking. The kitchen is no exception, which can be supplemented with bar stools. Such pieces of furniture are presented in abundance in modern stores, but their cost can be quite high. In addition, some consumers are not satisfied with the design of the described interior items. Therefore, their manufacture is sometimes done by home craftsmen on their own.

Instrument preparation

Do-it-yourself bar stools can be made only by preparing a certain set of tools and materials. Among the first should be highlighted:

• screwdriver-drill;
• grinder;
• pencil;
• drill;
• jigsaw;
• plane;
• roulette.

When preparing a screwdriver, you must take care of the availability of a set of bits. The jigsaw should have saw blades that will allow for clean cutting of plywood and wood. The grinder can be replaced with sandpaper. As for the drills, their length should be 3 and 6 mm.

Making a chair from solid wood

If you decide to make bar stools with your own hands, then you can use birch or pine. birch array better fit if you plan to tint products, because pine is stained unevenly. To carry out the work, an array is required, the thickness of which is 20 and 30 mm.

From a material of greater thickness, it is necessary to cut a circle with a diameter of 360 mm. This part will become the seat. If you have access to a manual router or milling machine, then you can select a profile around the perimeter. If this is not possible, then a uniform chamfer should be removed, and then the surface should be sanded. This recommendation applies to all blanks.

If you decide to make bar stools with your own hands, then at the next stage a small circle with a diameter of 260 mm will need to be cut out of an array of smaller thickness. From the same material, stiffeners should be cut, which act as a footrest. The legs should be cut out of an array of more impressive thickness. It is important to pay attention to the fact that the wood structure must be vertical.

Self-tapping screws are used for the screed. Dimensions equal to 5x80 mm will be needed to screw the legs to the small circle and to each other. In order to fix the seat to the small circle, 5x40 mm self-tapping screws should be used. To install the stiffeners, self-tapping screws 5x20 mm are used. The ribs must be installed on the legs with the help of corners. On final stage the product can be stained, dried, and then painted with several layers of varnish.

Another option for making a bar stool

If you decide to make bar stools with your own hands, then you should consider several technologies at once. The second involves the use of plywood, the thickness of which can vary from 25 to 30 mm. The legs can be made from balusters or shovels. The diameter of these elements should be approximately 30 mm.

To perform the work, a 30 mm drill should be prepared. For one chair, you will need four legs, each of which is 750 mm long. The seat radius will be equivalent to 180mm. It will also be necessary to cut out the draft seat, its radius should be equal to 170 mm. When a wooden bar stool is made with your own hands, you will need to cut the upper ring, its outer radius should be 143 mm, while the inner one will be 110 mm. The bottom ring should have outer and inner radii that are 153mm and 120mm respectively.

Work methodology

Before you start cutting out the rings, they should be marked for drilling. On the workpiece, draw the outer contour of the circle and draw two perpendicular straight lines through the center. From the crosshairs, 140 mm should be set aside in each direction, which will allow you to get the center points of the holes, they should be selected with a spade drill.

Next, the inner contour is determined, at this stage it will be necessary to cut the ring out of the workpiece. The rough seat is marked using the same technology as the top ring. However, only half the thickness remains to be drilled. This will allow you to get sockets for installing legs. When a do-it-yourself bar stool is made of wood, the details should be processed, as in the first version of the chair.

The legs should be fixed to the rings with furniture screws. They will need 8 pieces, and the size of each will be 6x70 mm. Don't forget the pucks. For them, you will need to prepare holes. The top ring does not need to be tightened tightly. First, the legs are installed in the nests, where you first need to pour a little wood glue.

The draft seat is additionally screwed to the legs with 5x60 mm self-tapping screws. In this case, it is important to drown the heads of the fasteners. The main seat is strengthened from above, it must be strengthened from below using 4x40 mm self-tapping screws. Before you make a bar stool with your own hands, you must prepare the stain. The surface of the chair is covered with it at the final stage.

Making a metal bar stool

Bar stool do-it-yourself metal can also be done. If there are remnants of sheet iron or a metal profile in the arsenal, then all these materials will be used. The shape of the future seat should be depicted on the surface of the asbestos sheet for welding. Using the sketch, you should cut out the workpieces and weld them together. The result is a polygon, the inner plane of which has yet to be filled.

To do this, blanks are cut from the same strip, you can use your own invented pattern. The blanks are welded together and cleaned, and the corners should be rounded. Legs are welded to the seat, for this you can use a profile with dimensions equal to 30x20 mm.

If you decide to make bar stools with your own hands, it is recommended that you first consider the photo. They will help you avoid many mistakes. In the process of welding, the legs will need to be grabbed at one welding point. The footrest levels are marked at a distance of 45 cm from the seat. In this case, you should be guided by the comfort of using the future chair.

Stops for legs should be made from the same profile. So that the legs do not squeeze finishing floors, rubber or plastic plugs can be put on them, instead of which decorative heels are sometimes used. They must first be cut to size and sanded.

Conclusion

Plugs do not need to be fixed with screws or glue, they will hold on their own. The main requirement in this case is to grind them to fit the size of the legs. When such a bar stool is made with your own hands, it is advisable to prepare the drawings in advance. Thanks to them, it is possible to accurately calculate required amount material, and generally facilitate the work process. Well, at the final stage, the chair should be painted, but first it must be covered with a layer of soil.

Happy residents of apartments of an acceptable layout or private houses have long understood the delights of free movement around the kitchen. And many male owners are happy to continue to improve the interior and furniture with their own hands. Quite often there are options for combining kitchen and dining spaces. As a rule, they are partitioned off with bar counters or kitchen "appendices" - continuations of the countertop. Chairs or stools for such racks sold in stores often have absolutely no “home” look, so we suggest making a bar stool with your own hands.

Appearance of the first bar stool

For both options below, you will need hand power tool. In this case, you do not have to order sawing on the side, since all the details are curly and relatively small size. Blanks for them can be bought at the construction market, in departments selling plywood and furniture panels.

Required Tools

• Screwdriver-drill with a set of bits.
• Electric jigsaw with files for a clean cut on wood and plywood.
• Sander or just sandpaper and a lot of patience.
• Plane.
• Pencil.
• Roulette.
• Drills with diameters of 6 and 3 mm.

Solid wood bar stool

The most affordable types of wood, sold immediately in the form furniture panels are pine and birch. If you plan to tint the product, that is, cover it with stain before varnishing, it is better to choose a birch massif, because pine is stained unevenly.

We need an array of two thicknesses: 30 and 20 mm.

From a thirty-millimeter cut out with a jigsaw a circle of diameters of 360 mm - this will be a seat, that is, the top of the chair. If you have access to a milling machine or manual frezer- you can choose a beautiful profile around the perimeter with a curly cutter. If this is not possible, simply remove a uniform chamfer with a planer and grind. This applies to all details.

Large and small seat circles

A small circle with a diameter of 260 mm is cut out of an array 20 mm thick. Stiffening ribs are cut out of it, serving as a footrest.

Drawing of bar stool legs

You can see the exact drawing of stiffening ribs and chair legs with dimensions in the pictures. The legs are cut from an array of thirty, and you need to pay attention so that the structure of the tree for the legs is vertical.

Drawing of stiffeners

The assembly order is visible in the pictures, for screeds you need to use three types of self-tapping screws:

• 5x80 - for screwing the legs to each other and to a small circle.
• 5x40 - for attaching the seat to a small circle.
• 5x20 - for attaching stiffeners. These parts are screwed to the legs with the help of corners placed from below, from the side of the floor.

We drill holes with a diameter of 6 mm into the plane under the screws, and into the end face - with a diameter of 3 mm.

Bar stool assembly

We tint with a stain, be sure to dry it and cover it with two or three layers of varnish. The bar stool is ready.

The second version of the bar stool

For the second option, we use plywood, 25-30 mm thick. The legs for it can be made from round balusters or simple cuttings for shovels, with a diameter of about 30 mm. To make bar stools with our own hands, as shown in the figure, we will additionally need a feather drill of the same diameter as the legs, that is, 30 mm.

The second version of the bar stool

So the details:

• Legs 750 mm long - 4 pcs.
• Seat, radius 180 mm.
• Draft seat, radius 170 mm.
• Top ring: Outer radius 143 mm, inner radius 110 mm.
• Bottom ring: Outer radius 153 mm, inner radius 120 mm.

Bar stool drawing

Before cutting out the rings, we mark them for drilling. We draw the outer contour of the ring on the workpiece and draw two straight lines perpendicular to each other through the center of the resulting circle. We measure 140 mm from the crosshairs in each direction - we get the centers of the holes that need to be selected with a pen drill, only four. We draw the inner contour and cut out the ring from the drilled workpiece.

We cut out the rings

The rough seat is marked in the same way as the top ring, but only half the thickness is drilled - these will be the “nests” for the legs.

All details are processed in the same way as in the first, wooden version of the bar stool.

The legs are attached to the rings with furniture screws at a height: Small 100 mm from the top, large - 250 mm from the bottom. We buy furniture screws with decorative caps in a hardware store, 6x70 mm - 8 pcs., Do not forget about the washers. We drill holes for them with a 6 mm drill. We don’t tightly tighten the upper ring yet - first we insert the legs into the nests of the draft seat, where we first fill in a little wood glue or PVA.

Additionally, we fasten the rough seat to the legs with 5x60 screws, trying to drown the heads of the screws. We glue the main seat on top and fix it from below, from the draft one, with 4x40 self-tapping screws.

We tint the product with a stain, varnish it, call the bartender.

Now we know how to make a bar stool with our own hands, and even in two versions. Objectively, they differ a little, but! With an array of wood for the first option, unpleasant incidents are possible. When choosing blanks for your parts in the store, be sure to ask the seller: Is it a structural array or a decorative one?

Decorative solid wood may look more attractive, but it will not withstand serious loads. With plywood, in this respect, it is easier and more reliable.

Good luck to you.

The spacious kitchen allows you to use the space to the maximum: here you can place not only the usual dining table, but also a bar with chairs. You can make a bar stool at home with your own hands, having a minimum set of tools and having the basics of woodworking. It will be a little more difficult to make furniture for the kitchen from metal pipes.

Furniture design

You need to start making a bar stool with your own hands by determining the material, as well as by measuring and creating a drawing. It is better to make a structure from wood (pine, birch) or metal (from pipes). A good economy option is plywood or chipboard panels, they are reliable and durable. Having chosen the material for the product, you can proceed to the next stage - inventing a shape and creating a drawing.

Do-it-yourself bar stools must have long legs, but everything else is optional. For example, the design may have a small back or a soft seat of a square or round shape. All this should reflect the drawings. When developing them, it is worth taking the height of the bar counter as a basis and subtracting 350 mm. Thus, the correct and convenient height of the furniture is obtained. This is the standard calculation. As for the height of the backrest, it should not be lower than 20 and not higher than 60 cm.

Features of creating a bar stool

Decided to make a chair out of wood? Logs are an excellent blank for the product.

Their thickness should be at least 20-30 cm, otherwise the chair will sag. However, if the thickness of the material is greater, then it is difficult to work with it. Logs need to be cut into 10 pieces, which must match the dimensions on the drawings.

• Seat circle. Thickness - 30 mm, diameter - 350 mm.
• Support for the seat in the form of a circle. Thickness - 20 mm, diameter - 250 mm.
• 4 wooden legs. Thickness - 30 mm.
• 4 straps for structural stiffeners. Thickness - 30 mm.

Please note: sawing should be done vertically so that the wood structure is not damaged and remains vertical, otherwise it will reduce the strength of the chair.

After cutting, the stage of assembly of the product begins. For this you will need:

• metal corners for fixing stiffeners to the legs;
• self-tapping screws 5x80 mm for fixing the legs of the structure to each other and for screwing them to a small circle;
• self-tapping screws 5x20 mm for fixing stiffeners;
• self-tapping screws 5x40 mm for fastening the seat to a small circle.

You need to start assembling a wooden chair according to this scheme: the legs are fastened together, then the stiffeners are installed on the metal corners, the small circle is screwed to the legs, and the main seat is fixed to the whole structure from above. The chair is ready! The product is varnished for practicality.

The second version of the wooden chair

The classic option for the kitchen is a high chair with a rectangular seat. As in the first option, in calculating the height, you need to build on the height of the bar counter. The classical optimal parameters are shown in the figure.

Logs are suitable as a material. Their thickness should be 30 mm, size 5 × 5 cm. After sawing the logs into the required parts, you can begin to assemble the furniture.

Start assembling the chair from the legs. To make them slanted towards each other, you need to transform them by beveling the corners and chamfers at both ends by 5 degrees. Now you can attach the top and bottom rails. Thus, it turned out 2 parts of the chair, parallel to each other. The next stage is the attachment of perpendicular partitions - at the top and bottom. It is important to understand here that the lower perpendicular partition will serve as a support for the legs, so it must be fixed at a convenient level.

We turn to the manufacture of the seat. At the end of the board, markup should be made, and then cut out the necessary shape. Give unusual curves will help a circular saw. Be sure to clean the part with a grinder.

The final stage is the connection of the legs of the chair and the seat. Holes are drilled at the tops of the legs and from the bottom of the seat, and 2 parts are fastened with pins. You can put them not only on pins, but also glue them with PVA glue to make the chair more stable. The product is covered with varnish or paint.

Metal bar stool

A metal product will decorate the kitchen interior in loft or industrial styles. Especially metal chair will look original at the bar in the kitchen. It can be made from iron pipes.

To create furniture you will need:

• piece of iron,
• pipe blanks preferably made of stainless steel (nickel-plated, chrome-plated, anodized),
• sheet of plywood or chipboard.

The diameter of the pipes depends on the type of furniture. But it should be borne in mind that the design must withstand the weight of a person and the pressure of the seat. It is recommended to take material with a diameter of at least 5 cm. The height of the legs is determined and the billet of pipes of the required length is cut off, preferably with a small margin of 1-2 cm.

Now we need to shape the material. This can be done using a pipe bender: the upper parts of the pipes are bent into a semicircle shape. They are fastened with fixing bolts to each other.

The seat can be made of metal or plywood. In the first version, the required shape is drawn on a piece of iron, then it is cut out and attached to a curved billet of pipes by welding or bolts. In the second version, the plywood base is cut out to the required shape and attached to a metal frame. In this case, the seat should be covered with a fabric with foam rubber so that it is comfortable to use. Please note: a chair with iron legs can scratch the floor, so you should “put on” plastic or rubber “socks”.

Recently, handmade interior items have become increasingly popular. They give the room individuality and can fully characterize its owner. Looks original kitchen furniture created by own design. For example, making a bar stool with your own hands is not so difficult. Such a hobby can become not only a full-fledged hobby, but also a good income.

Having opened any catalog of bar furniture, it is simply unrealistic to suddenly stop looking at a particular model, because the variety of shapes and colors is amazing. However, it is not always possible to find something suitable for your interior. In this case, it is worth making the furniture yourself. When making bar stools, a number of important parameters must be taken into account.

Properly calculated chair height is a guarantee of comfort. The optimal distance from the seat to the bar is 25-30 centimeters. The presence of such space provides comfort and freedom of movement.

A large surface area of ​​the furniture contributes to relaxation, immersion in an atmosphere of comfort. However, not every bar table can afford a wide scope. When thinking about how to make a chair yourself, you need to calculate the dimensions of the seat based on the width and depth of the table top. It is desirable that during operation there is no interference within a radius of 20 centimeters. This will provide comfort without violating the personal space of the person sitting at the bar.

When developing a chair design, it is necessary to consider the following components:

1. Base. Of course, everyone's preferences are different, but experts recommend the use of four legs. They will give the bar stool maximum stability and reliability. It would be useful to think about the possibility of adjusting the height, provided that among family members, relatives, and acquaintances there are people of different heights.
2. Back. For snacks or other short-term use of the chair, this parameter is not of particular importance. If you plan to sit for a long period of time, then it would be wise to opt for a high, well-fixed back, which you can lean back at any time.
3. Armrests. This design element is voluntary. There are no specific recommendations. It all depends on personal preference.
4. Upholstery. Its presence is due to the prioritization between style and comfort. Hard chair seats made of metal, acrylic, plastic, wood look more stylish, fitting perfectly into modern interior. Soft models, covered with fabric or leather, are pleasant to the touch, more comfortable.

In the matter of choosing a design, the decisive factor is the overall interior of the room. Traditional furniture, for example, will not look quite appropriate in a room decorated in high-tech, bionic or brutalist styles. A hand-made bar stool should harmoniously fit into the design of the room, not stand out from the overall picture.

It is better to choose the color of furniture based on the overall colors premises. This is especially important for the base. But as for the seat of the chair, it is recommended to give free rein to the imagination. You can choose options ranging from plain colors to floral or animal prints. Then the bar stool will become a bright highlight in the interior.

On four legs

with back

with armrests

With and without upholstery

Bright design

What materials can be made

The base is a kind of foundation for the entire product, which takes on the main load, is responsible for reliability and stability. Therefore, if there are people weighing more than 90 kilograms among those who will sit on the bar stool, preference should be given to more durable materials. These include wood, metal. The latter looks very expensive, solid, but gives the product a significant weight.

If it is decided not to use upholstery for the seat, then this structural element can be made of natural wood. This noble material will give the bar stool the look of expensive, high-status furniture. Its disadvantage is its high cost. Plastic is allowed. Particular attention should be paid to the transparent option. It is appropriate when creating an atmosphere of lightness and airiness. However, we should not forget that this material is not durable and, as a result, may crack with prolonged use.

If you decide to make the seat softer, more comfortable, then you can choose textiles or leather as upholstery. Natural materials are more suitable for the classic design of the bar stool. Artificial is best used when creating high-tech products and the like.

You can make a bar stool with your own hands completely from one material or combine several options. This will add charm to the interior details, will allow you to realize any fantasy. In addition, such a design will positively affect the final cost and functionality of the product.

Tree

Metal

Plastic

With leather upholstery

Required Tools

In order to make bar stools with your own hands, you need to have a certain set of tools in your arsenal. Most of the tools are universal, but there are some that can only be used when working with wood or metal. If they are not available, they can be rented.

Tool	purpose	Can be used for wood	Can be used for metal
Pencil	Marking
Screwdriver	Screwing in and out of threaded parts
	Accurate measurements
square	Building angles in 30°, 45°, 60°
Chisel	Sampling of recesses, cleaning grooves, creating a pattern
	Cutting blanks
Sandpaper	Product processing
	Connection of structural parts
Drill with drills with a diameter of 3 mm and 6 mm	Creating holes
	Bonding materials
Electric jigsaw	Sawing materials, creating curved cuts
	Gouging holes
	percussion work
screwdriver	Screwing in and out of connecting elements, drilling holes
	Fitting parts
Solvent	Giving paint and varnish liquids the desired consistency
	Surface painting
	Covering the outer sides of the product with a shiny layer
	Application of coloring components

At first glance, it may seem that there is too much equipment and materials. But experienced craftsmen know that it is better to have an extra tool in your arsenal than to interrupt and run to the construction department at the right time, during the creative process, for example, for the necessary drills or planer.

Dimensions and drawing

Before you start making a bar stool, you need to arm yourself with its drawing. This will make it possible to list necessary tools, accurately calculate the amount of material and avoid errors in work. The simplest and fast way- download the finished version. But since no one can give a 100% guarantee for the accuracy of the information, it is necessary to play it safe and personally check all the indicated sizes.

The next option is to independently draw a future bar stool using special computer programs. This process takes more time, but it guarantees the creation of a product that is unique in its kind. If there is no possibility or skills to work with a computer, then the drawings can be sketched by hand. To do this, you only need a sheet of paper, a pencil, a ruler and a great imagination.

How the drawing appears is not of fundamental importance. The most important - correct dimensions. It depends on them quality manufacturing bar stool. The following dimensions must be accurately measured and marked on the drawing:

• the height of the product from the floor to the seat (equal to the distance to the countertop minus 25-30 cm); standard - about 75-85 cm;
• back height (if available) - about 20 cm;
• seat length and width - at least 35 cm;
• the distance between the legs at floor level is approximately 44 cm.

The above standard sizes can vary according to individual preferences and dimensions of the bar counter. It will be interesting to look at a folding chair with an adjustable back height and sliding legs. For him, the drawing takes into account all the parameters in the retractable state.

DIY manufacturing

You can make a bar stool with your own hands from wood in the form of a stool or with a soft seat and back, as well as from plywood and metal. When working with the latest material, the master requires certain skills in welding. Therefore, most often they use a profile pipe, for which special knowledge is not needed.

wooden stool

Wooden furniture harmoniously fits into many interiors. It creates an indescribable atmosphere of coziness, comfort and warmth. A chair made with my own hands, will bring both aesthetic joy and practical benefits. It is recommended that a novice master try to create a simple wooden stool first, following the steps:

1. Purchase of wood. Most available materials- pine and birch. It is better to purchase shields with a thickness of 20-30 mm. If there is old, unnecessary wooden furniture, then you can use it.
2. Drawing markings on the material according to the drawing with a pencil.
3. Cutting parts with a jigsaw. One circle - the seat itself with a diameter of 36 cm and a thickness of 3 cm, the second - a substrate under it with a diameter of 26 cm and a thickness of 2 cm. You also need four legs 3 cm thick (vertical wood structure), four stiffening ribs (footrest) 3 cm thick It is recommended to plan the legs with a planer along the entire length, reducing the thickness downwards to 2.5 cm.
4. Chair assembly. Using a screwdriver or a screwdriver with 5 x 80 screws, the legs are connected to each other and with a small circle, with 5 x 40 screws the seat is screwed to a small circle, with 5 x 20 screws, through the corners, the stiffening ribs are attached to the supports.
5. Sanding the entire chair with sandpaper.
6. Coating the product with stain or varnish with a brush.
7. The wooden stool is ready.

The undoubted advantages of wooden products are durability and aesthetics. But you need to take into account such a moment: upon contact with water or at high humidity in the room, the product can quickly become unusable, swell.

We make markings according to the drawings

Cut out the details

Assembling a chair

Wooden stool ready

Made of wood with padded seat and back

Having trained on a bar stool in the form of a stool, you can move on to creating a wooden model with a soft seat and back. Such a product is more comfortable and aesthetic. Below is given step-by-step instruction for the manufacture and fastening of parts and a description of the process:

1. Materials for the chair are purchased.
2. Markings are applied to wood.
3. Parts are made from wood. Of the tools you will need a jigsaw and a chisel. You will also need parts from the following sizes: seat 34 x 34 x 2.5 cm, two front legs 2 x 44 x 74 cm, two rear legs 2 x 44 x 99 cm, front side 2 x 44 x 27.2 cm, rear side 2 x 44 x 32 cm , two side connecting strips 2 x 44 x 29.6 cm, two legs 1.5 x 22 cm each, four side legs 15 x 29.6 cm, two crossbars for the back 2 x 44 x 38 cm.
4. The front part of the chair seat is cut in an arc, cleaned with sandpaper. On the other hand, nests 2 x 2 cm in size are knocked out with a chisel.
5. On all sides, spikes are made with a hacksaw, on the side with a drill, two blind holes of 0.8 cm are drilled.
6. In the legs, sockets are created for the spikes of the connecting strips according to the drawing. In the rear elements, a place is prepared for the back. Using a chisel, the upper part measuring 2 x 2.5 cm is removed.
7. All details are carefully polished with sandpaper.
8. Then you need to assemble the chair with a screwdriver, drill and self-tapping screws.
9. Paintwork is in progress.

To create a soft seat, the following elements are needed:

• furniture foam rubber or batting as a substrate;
• upholstery material: natural or artificial leather, textiles;
• stapler and furniture glue.

Glue is applied to the top and sides of the seat, the edges of the filler and the edge of the upholstery material and aged for about 3-4 minutes. Then the substrate is pressed tightly against the base and covered with upholstery, which is fixed with a furniture stapler. After that, the seat is attached to the already made, painted chair frame.

We make parts from wood

From the details we assemble the frame

Fasten with self-tapping screws

We carefully grind

We carry out paint work

Preparing foam and upholstery

Cut the foam to the size of the seat and back

We cover with upholstery fabric and fix with a stapler

Attach the seat and back to the frame

Bar stool with backrest and upholstered seat

From a profile pipe

Recently, metal pipes have become widespread in the manufacture of furniture. Master classes with their use are recommended for beginner craftsmen. From profile pipe the body of the chair is made. Therefore, it is better to give preference to stainless steel, because products made from it are characterized by strength and durability. How to make a bar stool with your own hands from pipes - this is the next master class. You must follow the instructions below:

1. Stock up on the required material and tools: foam rubber, upholstery, metal pipes, fasteners, chipboard or plywood, pipe benders, drill, screwdriver or screwdriver, construction stapler.
2. In accordance with the drawing, cut blanks from metal profile. After that, give the upper part of the pipes a semicircular shape with a pipe bender.
3. Connect the bent parts to each other by means of fasteners using a screwdriver or screwdriver.
4. The seat is cut out of plywood or chipboard. The shape can be either round or square. To give softness, apply foam rubber, cover it with a cloth and fix it all on the underside with a stapler.
5. Connect the two parts of the structure with bolts.
6. From below, plastic or rubber plugs should be inserted into metal pipes. This will protect the floor from scratches.

A chair made of pipes will perfectly fit into the high-tech interior. classic kitchen, playing in contrast, it will add a casual atmosphere to the bar, and in a minimalist one it will be in perfect harmony with the design of the room.

We prepare materials

We assemble the parts of the chair with the help of corners and fasteners

Assembled frame made of metal pipes

We fasten metal carcass to the prepared wooden seat

Installing protective caps

Bar stool from a profile pipe is ready

From plywood

A fairly simple material to work with is plywood. Unlike wood, it is more moisture resistant and reliable in operation. The instruction for creating such a model is similar to the manufacture of a bar stool made of wood:

• in accordance with the drawing, markings are applied to the plywood, then blanks of parts (legs and seat) are cut with a jigsaw, which are subsequently polished with sandpaper;
• holes for hinges are created on the parts with a drill, recesses are hollowed out with a chisel;
• all components are assembled in one design;
• the chair is varnished or painted.

Most the best option when creating a bar stool, coniferous plywood will be used. This material is wear-resistant, retains an attractive appearance for a long time. appearance, less susceptible to the spread of fungi and the appearance of bugs. In addition, at first, coniferous plywood products will exude a pleasant aroma.

We mark the plywood sheet and cut out the details

We assemble the back

Plywood bar stool ready

Decoration methods

To give the bar stool a personality, it can be decorated in various ways. Due to the variety of colors and prints, the seat upholstery made of leather or textile (jacquard, microfiber, silk) will make the furniture a bright element of the interior. Cases will become great solution For those who don't want to be skinny. They are practical, they can be replaced at any time.

Decoupage is gaining more and more popularity in decorating furniture. It is used when working with wood as follows: the surface is cleaned with sandpaper, smeared with putty and painted, then decorations from napkins, flower pictures are glued. In conclusion, the product is varnished.

If creativity is not developed enough or there is simply no time, then you can decorate the chair with bright colors, which will also make it unique. An interesting solution will be the use of jute rope - it can wrap structural elements. The choice of decoration methods is huge. It all depends on tastes, desires, abilities, fantasies. Be that as it may, a bar stool made and decorated with your own hands will become the highlight of any interior, the pride of the master.

In decoupage technique

(no ratings yet)

If your house or apartment has a bar counter, you can complement it with exclusive chairs. To do this, you only need a few simple carpentry tools, a piece of plywood or board, bars and a little free time. So, we will describe in detail how to make a bar stool with your own hands.

Bar stool details and their dimensions

In fact, a bar stool is a high stool with footrests. Depending on your desire, it can be either massive, made of thick timber, or light, elegant, with round or square legs. The principle of its assembly in any case will be the same.

The height of the bar stools should be such that 30-45 cm remain between them and the tabletop. The seat can be made of prefabricated boards or two plywood circles(it is better to take plywood thicker, from 3 mm, so that it does not bend and break under the weight of the weight). The first circle will serve as an intermediate mount, and the second will serve as a seat.

For a country-style room, you can make a more massive bar stool with thick square legs. If they expand slightly downwards, then the product will turn out not only more aesthetically pleasing in appearance, but also more stable. Round and even turned legs can be ordered from a carpentry workshop or bought from an online store. If you know how to work with wood a little, you can carve them yourself even on the simplest home-made lathe. Curvilinear parts are sawn out with a circle saw (bow saw).

Round and chiseled legs

Sawing details

1. Just like for a regular stool, for a bar stool we need: 1 seat, 4 legs, 4 legs (bars connecting the legs in the middle or lower part) and 4 drawers (bars located under the seat). Naturally, all paired parts must be equal in size.

2. For ripping, it is better to fix the workpiece in the clamp of the workbench.

3. To obtain a stable product, cuts must be made strictly at 90 °.

4. Do not forget that when determining the length of the prolegs and the side, it is necessary to add the length of the spikes to it.

5. Sawing starts from one end, and, having reached the middle, they take out the workpiece, turn it over, fix it again and continue to work on the other side. Since in order to obtain a smooth surface, we will have to grind off the edge and then grind it with sandpaper, it is worth leaving a small allowance of 5 millimeters.

6. In order not to catch a burr, we carefully process each detail first with a large and then with a small pinch.

original bar stool

Spikes and grooves

On the network, some users recommend not to bother and screw the legs onto the bolts. Moreover, such products have recently begun to appear even on the shelves of furniture stores. But, alas, a chair assembled by this method will loosen in a couple of weeks. Therefore, we advise you to use the standard furniture assembly method - tenon-groove connection. In this case, the end of the part enters the groove, in which the fibers are located across, which makes it possible to ensure high strength of the product. With a tight fit, such a connection is able to withstand even an oblique load.

tongue-and-groove connection

On milling machine it can be done in minutes. However, manually, in the old-fashioned way, it is quite possible to prepare several tenon-groove fasteners for a chair. To do this, it is enough to have at hand only jigsaw or saw with fine teeth and rasp. The grooves are cleaned chisel. It is very convenient to choose a tree from a groove engraver- steel cutter

1. The width of the tenon-groove connection according to the standard should be equal to one third of the thickness of the workpiece, and its length should be 80% of the width of the part.

2. The location of the prolegs is determined arbitrarily. Since the legs of the bar stool are quite long, the design can be strengthened with additional thin prongs located closer to the seat. They are made thinner than the lower ones.

3. Work begins with the creation of a groove. In this case, the spike will be easier to fit using the groove as a template. We outline its length by making a line with a pencil on the side of the beam. First, we prepare several small holes in a row with a drill or screwdriver, and then choose a chisel excess wood.

4. Now we do thorn. It is more convenient to cut it with a jigsaw or a saw with fine teeth. We pre-fix the workpiece in the clamp of the workbench. For fastening a bar of small thickness (up to 4 cm), a single spike is sufficient.

Creating a cleat for a tenon

Can be made and plug-in spikes (dowels). Holes for them (as well as for standard spikes) are prepared a little deeper by 2 mm of their driving depth - this free space we'll drip glue. Accordingly, it is necessary to drive the spike into the hole so that it rises 3-4 mm less than the thickness of the part.

Plug-in spikes (dowels)

Assembly order

1. To check first collect the chair dry, without glue: we connect the first two legs with a drawstring and a proleg, then we prepare the second same frame, and only then we connect both frames. We check all corners with a square. Beveled or heaped parts will give the product a sloppy look, so even minor defects should be eliminated.

2. If there are no errors, we drip into the holes a little glue, carefully distribute it with a small brush or a torch and with a rubber mallet (mallet) carefully hammer it into a spike.

3. So that the prolegs (lower bars) can serve as a support for the legs, it is better to lower them lower.

Thinner additional prolegs can be made closer to the seat

4. We attach the seat to the drawers with screws or glue.

5. After the glue has completely dried, the product can simply be stained or painted in the desired color.

6. As a stuffing material for the seat, we use foam rubber or polystyrene, and for the upholstery itself, synthetic leather or any durable fabric - furniture, tapestry, etc.

7. The seat of the bar stool can be simply painted in a contrasting color.

Bar stool with decorative seat

Video: How to make a simple bar stool