Homemade indoor fountains. Do-it-yourself decorative fountain in the country: a step-by-step analysis of the construction stages. Building a stone fountain

The intense rhythm of our life involves periodic rest, both physical and moral, and there is nothing more pleasant than to sit in silence, enjoy beautiful view and pleasant sounds.

For this purpose, decorative fountains for an apartment can be suitable, which fully meet all these requirements.

After all, there is nothing more pleasant than listening to the sound of murmuring water and looking at a pouring fountain. And build it in an apartment, even if Not large sizes, a completely manageable problem.

In addition to those listed useful properties of this facility, the fountain in the apartment is a good air humidifier.

In contact with

Classmates

Types of mini-fountains at the place of application

Small home fountains can be divided into several types. According to the place of application, they are divided into country and indoor fountains. It is clear that a country fountain, in most cases, is installed on the street, and a room fountain in a city apartment. The country fountain is made large and it is important to choose the right place for its installation.

Do-it-yourself decorative fountain in the apartment video:

Place to install a country fountain

When choosing a place, it is important to observe three important conditions:

1. It is highly undesirable to install near trees. Firstly, growing roots can damage the fountain bowl and its waterproofing. Secondly, falling fruits and leaves can also disrupt the water system and the bowl.
2. If the fountain is installed in open areas, then flowering of water may occur due to direct exposure to the rays of the sun.
3. If the fountain is installed in the immediate vicinity of the house, then additional dampness may form on the building during windy weather, due to the drift of water drops from the fountain towards the house.

Classification of fountains according to the type of falling water

According to the type of falling water, a decorative fountain can be divided into several types.

1. Waterfall. This view has a ledge design with falling water. It has a beautiful appearance and is used most often.
2. Cascade. The installation scheme is the same as that of the first type, only it consists of several water flows. The liquid in them overflows along thresholds or inclined ledges.
3. An ordinary fountain, made in the form of a jet beating up and spraying spray around it.
4. Fountains made in the form of streams and lakes. They have an original appearance and are becoming increasingly popular.

Do-it-yourself indoor fountain

Looking at the decorations of some fountains, it seems that their manufacture and installation are very difficult to perform. Yes, there are rather bulky designs, and their installation will require you to have serious professional skills and knowledge, but a small mini-fountain with your own hands is quite capable of being made by almost every person who has simple skills in construction and installation work. In addition, you will create a design based only on your preferences and taste, the most suitable for your home interior. In addition, you will save a lot of money.

Materials and tools

So, if you still do not know how to make a mini fountain in your apartment, then read our step-by-step instructions. Before starting this work, you need to purchase necessary materials and tool.

• Fountain container. It can be a basin, a flower pot or something else at your discretion.
• The hose used to clean the aquarium is about 10 cm long.
• Polyethylene with dimensions slightly larger than the container.
• Glue waterproof, expanded clay.
• Aquarium pump.
• Medium or large sink, and stones or pebbles to strengthen it.
• Small shells and colored ground used for decoration.

The bowl for the fountain, which we choose, needs to be checked for cracks and holes in order to prevent future leaks.

Fountain materials

Pump installation

If you are making a tabletop fountain, then you first need to find a hose to work through which a stream of water will come out. To do this, cut off 10 cm from a regular aquarium hose and insert it into the pump. Immediately check whether your system is in working condition so that you do not return to this issue later. We install the pump to the bottom of the tank and fill it with expanded clay. Do not forget to level the surface after backfilling.

Final work

After you have filled up the expanded clay, you need to cover it with a film, having previously made a hole for the hose. Then we put decorative soil on the film.

Note!

For a sea shell, it is advisable to make a base of stones and fix them to the shell using waterproof glue.

The next step is to push the tube through the stones and the sink, after making a hole in it. The end of the hose should protrude from the sink by about 1 cm. The surface of the fountain should be decorated with stones and shells at your discretion. Thus, you saw that you can make a table fountain with your own hands without spending significant effort and money.

Advantages of a fountain without a pump

If you think that when building fountain structures, it is imperative to use a mini fountain pump, then you are mistaken. You can make a small fountain without using a pump, while it will work solely thanks to the laws of physics.

Yes, in these designs there are some restrictions on the power of the jet, but then you do not have to spend money on electricity and buy and connect a pump. You need to know that such a fountain should not be large, otherwise you cannot do without a pump.

decorative fountain

How the fountain works

Such a fountain will work on the principle of communicating vessels, with only some peculiarities. They need to be placed on the same level, connected to each other by two tubes. It is better to take plastic containers and preferably of the same volume, and tubes with a minimum thickness for longer uninterrupted operation of the fountain. Tubes are inserted into the bottom of each vessel, preliminarily drilled holes which then need to be sealed.

Illuminated fountain

Final assembly and installation of the fountain

In order for such floor fountains to work without a pump, you need to use a third vessel, equal in volume or greater than the previous two. To this vessel, in the walls, closer to the bottom, make two more holes, where you insert the two ends of the tubes from smaller containers.

We also tightly seal the inlets of these tubes, and insert a T-shaped adapter into the bottom of a large vessel. After that, the design of your fountain is considered complete. You will have to arrange it according to your taste, preferences and combination with the interior of the apartment.

Garden fountain

Where can I install apartment fountains. As you probably already understood from the above, fountains for an apartment are the most various kinds. In addition, they can be installed not only on the floor, but also on the table and even on the wall.

Note!

Desktop structures are usually the smallest in size and can even be placed on bedside tables and a window sill.

Floor fountains depend on the size of your apartment and can look quite impressive. Wall fountains look like real works of art and look like pano or paintings.

Their installation and manufacture, of course, is more complex and requires much more skills and material, but with a successful performance of your own, you will get indescribable pleasure contemplating them.

Watch a video on how to make a decorative fountain in an apartment with your own hands:

In contact with

See inaccuracies, incomplete or incorrect information? Do you know how to make an article better?

Would you like to suggest photos for publication on a topic?

Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!

Even the smallest pond is able to decorate your own summer cottage and give it a twist. And a do-it-yourself fountain will not only become a favorite place to relax and provide aesthetic pleasure, but will also become an occasion for compliments from invited guests.

But not everyone decides to build this mysterious hydraulic device with their own hands. Some summer residents mistakenly believe that the construction of a fountain is a laborious and expensive process, and one cannot do without the help of specialists in this matter. But every fan of spending time in nature can give himself such pleasure, the main thing is to know all the nuances of building a fountain with his own hands.

SELECTING THE TYPE OF THE FOUNTAIN

There are two types of fountains according to the type of construction.

1. The open version involves the supply of water to the nozzle. The formation of a jet in this version of the device occurs due to changes in the water level. The water pressure in this case is weak, so it is necessary to constantly monitor the water level. In addition, the water in such a fountain quickly becomes contaminated. To create it, you need to install a small tank at a height of about one meter above the nozzle.
2. A fountain with pump installation is the most practical and effective option. Thanks to the placement on the bottom of the pump, continuous circulation of water is ensured. Here, the pressure is stronger and the visual effect is more beautiful.

By design, pumps that act as fountains are divided into submersible and surface (stationary).

THE OPTIMUM PLACE FOR THE FOUNTAIN

picking up comfortable spot for the construction of a fountain, it is recommended to take into account the degree of slope of the earth. If the plot is uneven, it is better to place such a decoration in a lowland. This option for the location of the reservoir will allow not only to adjust the volume of groundwater, but will increase the oxygen saturation of the air.

• too close to the house so that moisture in windy weather does not get on the walls;
• in open areas, in order to prevent water from blooming due to ingress sun rays to the pond;
• next to the trees so that the leaves, seeds, fluff falling from them do not clog it, and the roots do not damage the waterproofing.

The fountain should be located in such a way that it is not an obstacle on the way to other buildings and is visible from all points. It is recommended to place the structure near the resting place.

The minimum distance that must be maintained between the fountain and plants, buildings, furniture is 50 cm. So the plants will not die from excessive moisture, and the furniture will not become unusable. Perfect option for the location of the fountain - partial shade and a place protected from the wind, located in proximity to a source of water and electricity. This arrangement will save you from unnecessary wires and additional work for their isolation.

Having decided on the place, it's time to think about the shape and depth of the future fountain.

PREPARATION OF MATERIALS FOR CONSTRUCTION

For the construction of a fountain in order to save money and effort, you can use the technology of building an ornamental pond with its equipment with a pump.

Materials needed to build a fountain:

• fountain container;
• pumping station;
• durable film;
• bayonet shovel;
• natural stones of various sizes;
• sand, gravel;
• decorative elements.

TANK SELECTION AND INSTALLATION

If you plan to build a miniature fountain, you can use an ordinary plastic basin or any other small container as a reservoir.

For large reservoirs, old bathtubs or a self-dug pit are suitable. If a bath is used, it is necessary to dig a hole of such a size that its edges are not higher than the ground. All holes are securely sealed in the bath, after which it is lowered into the pit and strengthened with earth, stones and sand.

For a homemade tank, a hole is made of the required depth and covered with a dense, high-quality film, which is fixed along the edges on the surface with stones. Stones are also poured to the bottom various forms and sizes. It is important that the stones do not have sharp edges and cannot cut through the film. The stones are evenly distributed over the entire bottom of the future fountain.

SELECTION OF A PUMP FOR THE CONSTRUCTION OF A FOUNTAIN

In order to construct a fountain on the site on your own, it is not necessary to purchase expensive materials, you can adapt any old elements. However, you should not spare money - the pump, the better it is, the more beautiful the fountain will turn out and will decorate the site for longer without causing problems.

Submersible pump - best option for the construction of a fountain at their summer cottage. Works on the principle of a centrifuge. You can also install a surface pump, it is mounted on the edge of the reservoir, but is most often used on large fountains and cascading reservoirs.

When choosing a pump, it is worth starting from the pressure that is constantly present in the pipe and the differences in this pressure. Therefore, buying the most powerful pump may not be justified, since not in all cases it will be able to work out its full power.

Regardless of which type of pump is chosen, it is important to remember that its power must be related to the diameter of the pipe. The jet of the fountain should come out under powerful pressure, and not slowly flow out of the pipe, since there will be no effect from such a design.

HOW TO MAKE A FOUNTAIN WITH YOUR HANDS: A STEP-BY-STEP INSTRUCTION

The construction of the fountain includes several main stages:

• pit preparation;
• fixing the trench;
• installation of a container or covering the bottom and edges with a film;
• installation of pumping equipment;
• fountain decoration.

FOUNTAIN WITH A POND FROM AN OLD TIRE

To build such a fountain you will need:

• an old tire from a truck or tractor;
• cement mixture, water, crushed stone and sand;
• container for mixing cement and a shovel;
• sealant;
• building level;
• mastic;
• stones;
• pump.

Stages of work:

VIDEO - FOUNTAIN FROM THE TIRE WITH YOUR HANDS

FOUNTAIN FOR COTTAGE USING FILM

For such a fountain you will need to prepare:

• thick film;
• shovel;
• sand;
• pump;
• stones different sizes without sharp corners.

Stages of work:

• we dig a hole, clear it of stones and tamp the bottom;

NEW LIFE FOR AN OLD BATH

For this version of the country fountain, you need to prepare:

• shovel;
• pebbles;
• pump equipment;
• bath;
• insulating tape;
• metal scissors;
• colored iron sheet;
• drill.

Stages of the construction of the fountain:

• we dig a pit corresponding to the size of the existing container;
• we put the bath inside and plug all the holes;

• we cut out wide strips from iron and lay them around the bath, close them with stones;

MINI FOUNTAIN FROM A PLASTIC BOTTLE

For this sprinkler you will need:

• plastic bottle;
• metal, strong wire or nail;
• insulating tape;
• garden hose.

Materials for a decorative fountain

Construction stages:

• decorate the pot with paints;
• make a small hole in the bottom of the pot;
• install a pump under the pallet;
• we drag the pump tube through the hole made in the pot;
• we fill the bottom with pebbles;
• decorate with artificial plants and figurines;
• fill the pot with water.

VIDEO - DECORATIVE FOUNTAIN OWN HANDS

FOUNTAIN DECORATION

You can emphasize the uniqueness of a handmade fountain by decorating it. It is recommended to lay out beautiful, multi-colored stones of different sizes around the reservoir, put flowers in pots, place cute figurines of animals, birds, and so on.

In order for the fountain to amaze with its beauty and unusualness at night, you can make it illuminated with the help of special equipment. Lamps installed around the perimeter of the fountain and lighting at its bottom will create a fabulous, magical atmosphere.

The bottom of the reservoir can be planted with special plants, bushes can be planted around the fountain.

Any country pond and fountain, including, needs careful care. To maintain the order and transparency of the water, a pleasant spring appearance of the structure, it is necessary to regularly clean the tank. By using special devices it is required to remove leaves, seeds, fluff and other objects from the surface of the water that can not only spoil the appearance of the reservoir, but also lead to a malfunction of the fountain.

At the end holiday season it is necessary to drain all the water, transfer the removable parts of the structure to a closed room, and cover the remaining parts and the bowl with a film so that dirt does not get into them.

It will not be difficult to build a fountain with your own hands in a country house or even in an apartment and will not require large financial resources. Before building a decorative fountain, you need to decide on the shape, size and installation location. There are many options for the location of such structures - at the gazebo, on the lawn, in the garden. After the construction of the fountain, you need to carefully monitor the purity of the water, regularly remove debris and add water, as it will evaporate.

Such designs are widely used in the design of suburban areas. Fountains can decorate any abandoned area or become a highlight suburban area. And by connecting fantasy and decorative elements, you can make it even more beautiful and unusual.

contemplative

landscape design

Even the smallest pond is able to decorate your own summer cottage and give it a twist. And a do-it-yourself fountain will not only become a favorite place to relax and provide aesthetic pleasure, but will also become an occasion for compliments from invited guests.

But not everyone decides to build this mysterious hydraulic device with their own hands. Some summer residents mistakenly believe that the construction of a fountain is a laborious and expensive process, and one cannot do without the help of specialists in this matter. But every fan of spending time in nature can give himself such pleasure, the main thing is to know all the nuances of building a fountain with his own hands.

There are two types of fountains according to the type of construction.

1. The open version involves the supply of water to the nozzle. The formation of a jet in this version of the device occurs due to changes in the water level. The water pressure in this case is weak, so it is necessary to constantly monitor the water level. In addition, the water in such a fountain quickly becomes contaminated. To create it, you need to install a small tank at a height of about one meter above the nozzle.
2. A fountain with pump installation is the most practical and effective option. Thanks to the placement on the bottom of the pump, continuous circulation of water is ensured. Here, the pressure is stronger and the visual effect is more beautiful.

By design, pumps that act as fountains are divided into submersible and surface (stationary).

Best location for a fountain

When choosing a convenient place for the construction of a fountain, it is recommended to take into account the degree of slope of the earth. If the plot is uneven, it is better to place such a decoration in a lowland. This option for the location of the reservoir will allow not only to adjust the volume of groundwater, but will increase the oxygen saturation of the air.

• too close to the house so that moisture in windy weather does not get on the walls;
• in open areas, in order to prevent water from blooming due to sunlight on the pond;
• next to the trees so that the leaves, seeds, fluff falling from them do not clog it, and the roots do not damage the waterproofing.

The fountain should be located in such a way that it is not an obstacle on the way to other buildings and is visible from all points. It is recommended to place the structure near the resting place.

The minimum distance that must be maintained between the fountain and plants, buildings, furniture is 50 cm. So the plants will not die from excessive moisture, and the furniture will not become unusable. The ideal option for the location of the fountain is partial shade and a place protected from the wind, located in close proximity to a source of water and electricity. This arrangement will save you from unnecessary wires and additional work on their insulation.

Having decided on the place, it's time to think about the shape and depth of the future fountain.

Preparation of materials for construction

For the construction of a fountain in order to save money and effort, you can use the technology of building an ornamental pond with its equipment with a pump.

Materials needed to build a fountain:

• fountain container;
• pumping station;
• durable film;
• bayonet shovel;
• natural stones of various sizes;
• sand, gravel;
• decorative elements.

Selecting and installing a container

If you plan to build a miniature fountain, you can use an ordinary plastic basin or any other small container as a reservoir.

For large reservoirs, old bathtubs or a self-dug pit are suitable. If a bath is used, it is necessary to dig a hole of such a size that its edges are not higher than the ground. All holes are securely sealed in the bath, after which it is lowered into the pit and strengthened with earth, stones and sand.

For a homemade tank, a hole is made of the required depth and covered with a dense, high-quality film, which is fixed along the edges on the surface with stones. Stones of various shapes and sizes are also poured to the bottom. It is important that the stones do not have sharp edges and cannot cut through the film. The stones are evenly distributed over the entire bottom of the future fountain.

Choosing a pump for building a fountain

In order to construct a fountain on the site on your own, it is not necessary to purchase expensive materials, you can adapt any old elements. However, you should not spare money - the pump, the better it is, the more beautiful the fountain will turn out and will decorate the site for longer without causing problems.

A submersible pump is the best option for building a fountain in a summer cottage. Works on the principle of a centrifuge. You can also install a surface pump, it is mounted on the edge of the reservoir, but is most often used on large fountains and cascading reservoirs.

When choosing a pump, it is worth starting from the pressure that is constantly present in the pipe and the differences in this pressure. Therefore, buying the most powerful pump may not be justified, since not in all cases it will be able to work out its full power.

Regardless of which type of pump is chosen, it is important to remember that its power must be related to the diameter of the pipe. The jet of the fountain should come out under powerful pressure, and not slowly flow out of the pipe, since there will be no effect from such a design.

How to make a fountain with your own hands: step by step instructions

The construction of the fountain includes several main stages:

• pit preparation;
• fixing the trench;
• installation of a container or covering the bottom and edges with a film;
• installation of pumping equipment;
• fountain decoration.

To build such a fountain you will need:

• an old tire from a truck or tractor;
• cement mixture, water, crushed stone and sand;
• container for mixing cement and a shovel;
• sealant;
• building level;
• mastic;
• stones;
• pump.

Stages of work:

Video - Do-it-yourself tire fountain

For such a fountain you will need to prepare:

• thick film;
• shovel;
• sand;
• pump;
• stones of different sizes without sharp corners.

Stages of work:

• we dig a hole, clear it of stones and tamp the bottom;

New life for an old bath

For this version of the country fountain, you need to prepare:

• shovel;
• pebbles;
• pump equipment;
• bath;
• insulating tape;
• metal scissors;
• colored iron sheet;
• drill.

Stages of the construction of the fountain:

• we dig a pit corresponding to the size of the existing container;
• we put the bath inside and plug all the holes;

• we cut out wide strips from iron and lay them around the bath, close them with stones;

For this sprinkler you will need:

• plastic bottle;
• metal, strong wire or nail;
• insulating tape;
• garden hose.

Stages of building a fountain:

• put the mini-fountain in the right place and turn on the water.

This option is perfect for watering the garden and garden.

Decorative fountain for home

To build such a fountain you will need:

• a large flower pot with a pallet;
• paints on glass and ceramics;
• small water pump
• contours;
• decorative balls, aquarium decorations.

Construction stages:

• decorate the pot with paints;
• make a small hole in the bottom of the pot;
• install a pump under the pallet;
• we drag the pump tube through the hole made in the pot;
• we fill the bottom with pebbles;
• decorate with artificial plants and figurines;
• fill the pot with water.

Video - DIY decorative fountain

Fountain decoration

You can emphasize the uniqueness of a handmade fountain by decorating it. It is recommended to lay out beautiful, multi-colored stones of different sizes around the reservoir, put flowers in pots, place cute figurines of animals, birds, and so on.

In order for the fountain to amaze with its beauty and unusualness at night, you can make it illuminated with the help of special equipment. Lamps installed around the perimeter of the fountain and lighting at its bottom will create a fabulous, magical atmosphere.

The bottom of the reservoir can be planted with special plants, bushes can be planted around the fountain.

Any country pond and fountain, including, needs careful care. To maintain the order and transparency of the water, a pleasant spring appearance of the structure, it is necessary to regularly clean the tank. With the help of special devices, it is required to remove leaves, seeds, fluff and other objects from the surface of the water that can not only spoil the appearance of the reservoir, but also lead to a malfunction of the fountain.

At the end of the summer season, it is necessary to drain all the water, move the removable parts of the structure indoors, and cover the remaining parts and the bowl with a film so that dirt does not get into them.

It will not be difficult to build a fountain with your own hands in a country house or even in an apartment and will not require large financial resources. Before building a decorative fountain, you need to decide on the shape, size and installation location. There are many options for the location of such structures - at the gazebo, on the lawn, in the garden. After the construction of the fountain, you need to carefully monitor the purity of the water, regularly remove debris and add water, as it will evaporate.

Such designs are widely used in the design of suburban areas. Fountains can decorate any ownerless area or become the highlight of a summer cottage. And by connecting fantasy and decorative elements, you can make it even more beautiful and unusual.

Even the smallest fountain is capable of transforming the landscape of a summer house or a private house beyond recognition. This decorative building will definitely become your favorite recreational area on your site, because it will give you the opportunity to unite with nature at any moment. Would you like it to become a reality sooner? There is nothing super complicated here - everyone can make a fountain with their own hands. Don't believe? Then to your attention step-by-step instruction with a photo, following which you can quickly and without the involvement of professionals get a spectacular and functional fountain.

First of all, you need to choose suitable option fountain for your site. We are talking about its dimensions, shape and materials. When solving this issue, be guided by the area and style of the courtyard of your summer house or private house.

So, for a large area, it is better to choose a classic sculptural model that will become the center landscape composition. And for a modest courtyard, fountains in the form of small architectural forms are suitable: sea shells, fairy-tale heroes, houses, pots and other similar figures.

Original fountain from improvised materials

But it is not necessary to buy a ready-made sculpture, because you can also build a fountain with your own hands. The simplest option is the construction of stones. To make it, lay large flat stones on top of each other, make holes in each of them with an electric drill and string all the resulting products on copper pipe- it is through it that water will flow to the top of the structure. Then close the gaps with small pebbles and seal the gaps with silicone sealant.

Choose a location

The next step is to decide where exactly on the site the fountain will be located. In order for the structure to fully fulfill its aesthetic function, it cannot be installed “anywhere” - it is important to choose the best location. And for this you need to take into account several nuances.

1. First, the fountain has no place on too open area, because under the influence of active sunlight, the water can begin to "bloom".
2. Secondly, the fountain cannot be placed among powerful trees - their roots can provoke deformation of the reservoir and waterproofing. In addition, leaves, fluff, fruits and seeds of trees will constantly pollute the fountain.
3. Thirdly, the structure should not be too close to the house, otherwise moisture with the wind will fall on its walls.
4. Fourthly, it is undesirable to stir the fountain in the open wind so that its gusts do not “tear off” the jets.

Position the fountain so that it can be seen from different parts of the site

Thus, the ideal location for a decorative fountain is a light penumbra surrounded by flowers and low bushes.

When you choose a place, proceed directly to the arrangement of the fountain. It suggests phased implementation three main groups of works:

• tank preparation;
• pump installation;
• installation and decoration of the fountain.

Preparing the tank

In order for the fountain to be durable and solid, it is necessary to equip a special reservoir for hydraulic equipment and water. This is done as follows:

• Dig a pit of a pre-calculated depth and the diameter you need.

Important! The depth level of the tank must be below ground level so that the soil around the fountain bowl does not wash away and the base does not deform.

• Pour a thin layer of sand on the bottom of the resulting pit and carefully reinforce its side walls with bricks.
• Lay inner surface pit with a dense plastic film - it will prevent the passage of water.
• Fix the film along the top edge of the tank and seal the seams with frost-resistant silicone sealant. Pour stones at the bottom of the pit, distributing them over the surface of the film. Stones should not be sharp so as not to deform the film.
• Install a small emergency drain near the pit in order to prevent the water level in the tank from rising.

Fountain construction

Installing the pump

The fountain will not be able to work without the most important mechanism - the pump. It is he who is responsible for the continuous movement of the water flow. General principle The operation of the pump is simple: water is ejected through the nozzle into the tank, then it enters the pipeline, where it undergoes coarse and fine cleaning, and then the already purified water is sent back to the nozzle.

The quality of the functioning of the fountain directly depends on the type of pump:

• Submersible - works on the principle of a centrifuge and is located in the center of the fountain tank under water. This is a cheap, but reliable device, for the installation of which no fasteners are needed - the submerged pump is quite heavy, so it does not budge. It is suitable for small weak fountains.

Diagram: fountain pump operation

• Surface - a more serious type of pump, which is not installed inside the tank, but on its edge on the surface of the earth. Such a device is designed for large fountains with a complex design.

The pipeline for the pumping system can be constructed from plastic pipes. Their optimum diameter- 16 mm.

Advice. In order to enhance the operation of the pump, additionally install a pressure tank - it will guarantee a constant pressure of the water flow.

Fountain decoration

After the main functional elements are installed, you need to take care of the installation of the fountain itself, or rather its upper part. If you are using ready-made sculptures, then they must be provided with special fasteners for installation. But a home-made stone fountain is best installed on metal slats, previously laid on top of the tank.

Then proceed to decorate the design. The fountain can be decorated with plants, stones of various sizes, clay figurines, microsculptures and any other details that seem appropriate to you on your site.

You can decorate the fountain with stones, sculptures and plants

Do not forget about such a spectacular decor tool as lighting. It can be underwater lamps, light strips, floating lanterns, ground lamps - here you are also unlimited. But remember that lighting structures must be completely sealed, and all their contacts must be protected from water as reliably as possible, otherwise it will be unsafe to use them.

When all work is completed, fill the tank with water and start the fountain.

How to see to do beautiful fountain with your own hands, you do not need to work hard and spend a lot of money. Do not deviate from the instructions, use quality materials and don't be afraid to experiment with decor - keeping these three simple rules, you will definitely get a functional fountain that will delight your eyes and tune in a positive way for more than one year.

Which fountain to choose for a summer residence: video

For any owner, the appearance of a summer cottage or yard has great importance. Its design can be done by specialists, but, if desired, you can do it yourself. A fountain will be a good decoration of the yard or plot. It can also be built according to your own project.

Types of fountains

Fountains for giving are different types. They are divided into types: by device, by appearance, according to the features of work, etc. According to the method of arrangement, country fountains are circulation and flow, they are also called "Roman".

Did you know? The first fountains appeared in ancient Greece and in ancient Rome.

Circulating suggest the water cycle. Water fills a certain reservoir (bowl, vase, reservoir) and with the help of a pump is supplied to the device, from which a stream of water directly shoots.

Everything is arranged so that the outgoing water enters the tank and swings up again. Thus, the device does not involve the supply of water from a water supply system or a well. The only thing that is needed is to add water to a certain mark, because it tends to evaporate or splash.

flow fountains arranged with the involvement of water supply (wells) and sewerage. Water flows up, falls down and goes into the sewer. The method is, of course, irrational, but such fountains have a number of advantages:

• aesthetic appearance;
• drinking water;
• the possibility of using water for watering lawns, flower beds, shrubs and trees.

By appearance and features, fountains can also be classified into single-level and multi-level, single and group, jet, waterfall, cascading, in the form of a ring or tulip, dancing, singing, colored, with a pond, with a reservoir, etc.

Did you know? The tallest fountain in the world- 312 m. It is called the fountain« Fahda» is located in Saudi Arabia.

Choosing the right place

If you decide to build a fountain on the site with your own hands, then, first of all, choose a suitable place for this. If there is a cottage or a pond, the choice of location is obvious. Where the pond is located, there will be a fountain. The device of the pond, of course, will have to be modified, corrected, but the foundation will remain.

If you are starting from scratch, then you need to choose a place, carefully weighing all the pros and cons. DIY garden fountains perform different functions: Humidify the air in the garden, which is good for trees, create a cool environment, can be used for irrigation, etc.

For this reason, you need to choose a place so that the fountain not only brings aesthetic pleasure, but is also useful. A suitable place for arrangement would be an open area between trees, shrubs or hedges.

Trees and bushes should not hang over a pond or reservoir so that debris does not fall into the water and leaves fall. This is bad for water filters. Also, due to the proximity of trees, and hence their root system, a violation or even destruction of the underground part of the fountain is possible. If plants grow in the country that cannot tolerate waterlogging, equip the fountain away from them.

Important! Do not place the fountain near buildings.

There is no need to equip the structure in the open sun, because this is fraught with flowering water. There is one more condition: a do-it-yourself fountain in the country should be in harmony with the overall design. Everything should be done in the same style. This should be a platform that is clearly visible from the windows of the house and from any part of the yard, because you are building a fountain, first of all, for aesthetic pleasure.

Preparation of materials for construction

When the place for the fountain and its type are chosen, the project is developed, it is necessary to determine what materials for construction will be needed. Let's assume that the project is designed for a circulating jet static fountain with a single ejection of water, i.e. of the "Geyser" type.

At home, to equip a fountain with your own hands, you will need cement, sand, gravel, a durable plastic film and a building facade mesh sized according to the diameter of the structure (both the film and the mesh must be the same size). In addition, you need a plastic container with a volume of about 50-70 liters, depending on the size of the structure.

If you plan to decorate everything with stones, then prepare them immediately. It can be a wild stone of the right size, cobblestone, granite, large pebbles, etc. A fountain pump will be needed to ensure proper operation.

Pump Selection Criteria

Depending on the type of fountain, you need to choose a pump. For the "waterfall" we would choose a surface pump, and since we have a traditional fountain, we choose a submersible one.

Usually, submersible pumps perform their function perfectly. They are compact, quiet, easy to install and, most importantly, affordable. Submersible pumps come in different capacities. It is calculated in the amount of pumped water per hour (l/h).

The height of the jet will just depend on the power of the pump. The maximum height is calculated by the diameter of the "foot" you made. The pump in this case does not need to be chosen according to the principle "the more powerful, the better." For the arrangement, we need such that the jet is high enough, and that the spray does not fly out beyond the "foot". For summer cottages, the height of the jet is suitable from 80 cm to 1 m.

Important! Care must be taken to ensure that water does not splash outside the fountain. Excessive moisture can lead to the death of plants and damage to things.

Manufacturers, as a rule, provide a table of the ratio of power and jet height in the instructions. Since we are equipping the Geyser, such a device will need a pump with a capacity of about 7000 l / h.

The principle of installation of the pumping system

The pumping system is installed 10 cm above the bottom on a stand (lined brick or mounting pedestal). A hose or pipe with water supply is supplied to it. Usually a sprinkler comes with a pump, but if it is not there, then you can make it yourself.

To do this, you can take a regular pipe made of stainless steel. The diameter will depend on the height of the jet and the diameter of the water spray. For a small fountain of 0.8-1.0 m, a diameter of 2-2.5 inches will suffice. The length will depend on how deep the pump is submerged. It is enough to leave 10-15 cm above the water.

To shape the jet, you can flatten the pipe, roll it, leaving a hole, drill a few holes, or cut a thread and screw on the desired nozzle. Connect to the pump directly or through an adapter (if necessary).

Fountain installation. Step-by-step instruction

Do-it-yourself master class for installing a fountain in the country with step by step photo easy to find on the internet. Typically, installation takes place in several stages. Arrangement for the selected project includes 10 steps:

Important! Be sure to follow safety precautions when performing any work on installing the fountain.