3,797 Views

Over time, gluing wallpaper to the ceiling loses its relevance. And many are faced with the problem of dismantling the old ceiling trim during a new renovation. They are removed not only because they are out of fashion, but also because they can become unusable. In addition, enough alternative materials have appeared. In this article we will tell you how to remove wallpaper from the ceiling.

Removing wallpaper from the ceiling

They can be difficult to remove due to the adhesive. The work performed must be of especially high quality for a good preparation of the ceiling for putty. Any renovation work it is worth starting with preparation. Ceiling finishing should be started before wall finishing. If carried out in a different sequence, you can damage the wall decoration.

The process will get pretty messy. Cover the floor if possible. For example, polyethylene. Please note that the protective coating will have to be thrown away immediately after the repair of the ceiling is completed. Otherwise, you will carry dirt. You also need to cover windows and doors.

It is better not to carry out such work if the room temperature is less than 5 C heat. Cover outgoing electrical wiring. Remove the chandelier and cover the wires.

Wear protective clothing, goggles and gloves. Be sure to cover your hair.

Of the tools you will need:

  • Spatula (may become unusable after work).
  • Building roller with long pile.
  • A bucket of warm water in any container.
  • Ladder.

Getting started

If the wallpaper was two-layer, remove it dry by prying it off with a spatula and peeling it off. If the method does not work, you must wet them with water or a commercial water-based solution. You can wet the wallpaper with a roller. Wait until the water is absorbed. If they are not wet enough, re-wet. Try removing the wallpaper again with a spatula.

If the material is waterproof, then make notches so that the water gets under the wallpaper itself. After that, you will most likely be able to remove the wallpaper. At least almost everything. Remains can be wetted separately and removed with a spatula.

Knock off any loose plaster with a hammer. Expand the cracks up to 1 cm and putty. If you find a fungus, treat it with an antiseptic several times.

After fixing any ceiling defects, apply a deep penetrating primer.

The renovation is accompanied by a change of wall covering, and you have to decide how to remove the old wallpaper. The process requires effort and differs depending on the type of substrate and the quality of the canvas. The old coating can be removed in various ways.

Preparing to remove wallpaper

Before starting dismantling, it is important to prepare workplace... Old coating does not always come off easily - tools should be at hand. Safety precautions are equally important.

Observance of precautions

It will not be possible to remove the old coating completely clean. Plaster may come off along with the wallpaper, old paint, dust. To preserve furniture or floors, you need to prepare the room.

Room preparation:

  • Completely turn off the electricity in the room.
  • Cover the sockets and switches with masking or office tape.
  • Take out the furniture.
  • Lay tape or newspapers on the floor.
  • Cover the skirting boards.
  • If there is furniture left, move it to the center and cover.
  • Leave a wet rag at the entrance - it retains dust.

What tools are needed for dismantling?

Different implements are used to remove the old coating. Material matters - some wallpapers are easy to remove, others need to be wetted or processed special composition... But there is a list of basic tools.

You will need:

  • Gloves.
  • Putty knife.
  • A bucket of warm water.
  • Dishwashing liquid.
  • Roller.
  • Sponge.
  • brush with metal bristles.
  • Washing off wallpaper.
  • Iron.

Basic methods and tools for removing old wallpaper

Each material has its own characteristics. How to shoot depends on the type of old paintings.

With water

The simplest and most obvious method. You can easily remove old self-adhesive, non-woven, paper and even vinyl wallpapers.

Tools:

  • A bucket of water at room temperature.
  • Roller.
  • Construction trowel.
  • Stationery knife.

Algorithm of actions:

Video

The full process can be seen in the video.

Mechanical method (steam and needle roller)

With this method, almost any old coating can be easily removed. The presence of a steam generator is a great bonus in the work. An alternative is an iron, but you need a sheet or a piece of cotton cloth.

Suitable for paper, non-woven, vinyl wallpaper.

Inventory:

  • Steam generator or iron with sheet.
  • A container with water.
  • A wallpaper tiger (aka a needle roller), but a clerical knife will do.
  • Putty knife.

How to remove wallpaper by ferry:


Video

Life hack for removing wallpaper with a steam generator, as well as comments can be viewed on the video.

Special chemicals

If the wallpaper is tight, it is difficult to remove it using traditional methods. To save time and achieve the best results, special chemical solutions are often used. They are sold in building supermarkets and help to quickly remove old canvases.

For which wallpaper is it better to use?

It is used for non-woven, paper, washable, textile wallpapers.

Required inventory:

  • Roller.
  • Rubberized gloves.
  • A basin of water.
  • Wallpaper tiger (if not, you can use a knife).
  • Putty knife.

Step-by-step instruction

  1. Dilute the substance with water according to the instructions.
  2. Roll the walls with a wallpaper tiger or poke them with a knife.
  3. Apply the composition to the walls with a roller.
  4. Leave the wallpaper to soak ( exact time is on the package).
  5. It is enough to pry the canvas with a spatula and tear off.

Video

See the video for details.

Removing old Soviet wallpaper takes effort. Often they are glued to the layer of newspapers under which there is old plaster... To begin with, you can try the traditional method - soak with water and peel off. If it doesn't work, use a liquid.

Removal features depending on the base and material

Different coverage has its own characteristics. This must be taken into account when choosing a removal method.

  • Vinyl. Leave easily. It is enough to soak them with water and remove after 20-30 minutes.
  • Paper. They come off easily if glued to high-quality glue (universal "Methylane"). They are removed with a knife or spatula. If they do not come off, soak with water or steam with an iron.
  • Non-woven. They have two layers, the top layer is removed. Ideally, it is better to steam old canvases or use a wallpaper remover.
  • Liquid. They are afraid of moisture. To "peel off" them, it is enough to soak the wall, after a while the coating will begin to lag behind the walls.
  • Washable. Processed protective compoundmoisture-proof. It is necessary to roll the walls with a needle roller, apply wallpaper remover, remove after a while.
  • Glass fiber. Removable easily. It is necessary to tear the sheets, fill the space under them with water. After 45 minutes they will start to lag behind. Or immediately fill it with a special liquid and peel it off easily.
  • Self-adhesive. Old sheets come off easily; to speed up the process, you can moisten them with boiling water or use a construction hair dryer.

How to peel wallpaper depending on the type of surface?

To remove old coating from walls, it is worth considering the type of surface. This will simplify the work and save you from additional manipulations after.

Drywall

The material is not resistant to moisture. It will not work to use water or chemical composition, as it will lead to deformation of the drywall. You can remove the old coating with steam (iron) or rip it off by hand using a knife. Work carefully so that the knife does not scratch the drywall.

Concrete walls

Concrete is not afraid of water and high temperature... You can remove the old coating in any way, you need to push off from the material of the canvases. Paper can be easily removed with water, washable, textile, vinyl and others - remove mechanically or chemical composition.

Wooden surface (plywood, chipboard, fiberboard, gvl)

Wood and plywood are afraid of moisture, and if the surface was not additionally processed before pasting with wallpaper, it will not work to remove the canvases by soaking. Steam can be removed from painted walls. A safe bet is a composition for removing old wallpaper. It does not deform wooden surface and will help remove the coating from minimum cost time. Or, carefully peel off the wallpaper with a knife or spatula.

The best way to shoot quickly and easily at home

To remove the coating quickly and effortlessly, it is recommended to use a wallpaper remover. Chemicals a convenient option for home - harmless to health, suitable for all surfaces (wood, drywall), a minimum of dirt and dust during work. You can remove old canvases and steam - the result is good, but if there is no steam generator, laborious work awaits.

How to remove old ceiling wallpaper?

Removing old wallpaper from the ceiling depends on the material. It is inconvenient to work with an iron on the ceiling, the option of soaking with water or a chemical solution remains.

You will need:

  • Stepladder or table.
  • Container for water.
  • Putty knife.
  • Roller.
  • Masking tape.
  • Film.

Prepare glasses, gloves, hat, old clothes from equipment.

Step-by-step instruction:

  1. Take out the furniture.
  2. Turn off the electricity, remove the chandelier (preferably).
  3. Tape up the sockets, skirting boards.
  4. Cover the floor.
  5. Moisten the roller in water or a special water-based solution.
  6. Blot the ceiling.
  7. Wait 25-40 minutes until the canvases are soaked.
  8. Gently pry the sheet with a spatula, remove.
  9. Do not turn on electricity, wait for the ceiling to dry.

What to do if the wallpaper is glued on PVA glue or bustilate?

If the old coating is glued to PVA glue, it will not work to peel it off with a spatula or scraper. Ideally, you need a device - a sander or grinder with sandpaper nozzles. The process is dusty, but the result is worth it.

If there are no such devices in the arsenal, a needle roller will help out. It takes a long time to scratch the old wallpaper. At the end, treat the walls with a wallpaper remover, tear them off.

To remove the old wallpaper pasted on the bustilate, you need to work for a long time with a scraper, a metal brush, and sandpaper.

  • If there is putty under the wallpaper, this method is not recommended, so that you do not have to re-finish the walls.
  • The steaming method is suitable for paper sheets.
  • Washable, vinyl and textile wallpapers are best treated with a chemical composition, and then removed calmly.

How to rip off in problem areas?

The job will take more time and patience. This applies to peeling old wallpaper in a room with stretch ceiling and behind the batteries.

From under a stretch ceiling

You will need:

  • A sharp knife.
  • Wide spatula (preferred).
  • Water or adhesive thinner.

Algorithm of actions:

  1. Place the trowel vertically on the ceiling.
  2. Use a knife to cut the blade along the edge of the trowel.
  3. Attach the spatula again by moving it.
  4. In this order, trim the wallpaper at the border with the ceiling around the entire perimeter.
  5. Moisten wallpaper with water or solution, remove.

Behind the battery

If the radiator can be dismantled, there will be no problems. For a stationary battery, you will have to wield a small spatula or knife. The result depends on the size of the radiator and how far the hand reaches.

Removing old wallpaper with your own hands without the involvement of masters should not be difficult. Manufacturers offer special chemical compositionsthat cope even with tightly glued old sheets. The main thing is to decide in advance on the method of removal, prepare the inventory and the room.

The ceiling is the most prominent place in the apartment. Therefore, all the flaws and flaws in the decoration will be immediately visible not only to residents, but also to guests. For this reason, it is recommended to entrust ceiling repairs only to professional performers. You can independently, unless thoroughly clean the surface.

Below we will look at how to remove old wallpaper from the ceiling and prepare its surface for repair.

However, here one cannot do without knowledge of small subtleties and secrets. You can, of course, pry off the edge of the wallpaper and try to tear it off. Only in this case, there will be tightly glued areas of paper that will have to be cleaned off with a knife or spatula. The apartment and everything that is in it, after such an action, will be a miserable sight - ingrained wherever possible, the whitish dust will remind of the decoration of the ceiling for many months.

It is much faster and more efficient to remove old wallpaper from the ceiling after wetting it. So, firstly, there will be much less dust and dirt. In addition, wet paper is much easier to separate from the surface. If later you have to work with a spatula, then just a little.

Since wet paper and damp concrete are good conductors of electricity, it is necessary to first de-energize the apartment to avoid accidents. After that, you can moisten the wallpaper with water. It is better if it is not just warm, but almost hot - so the process will go several times faster. It is best to use a large sponge or paint roller as a handy tool. You may need to wet the wallpaper several times before it absorbs enough moisture to easily and effortlessly fall behind the ceiling.

Despite all efforts, there may be areas where the paper is firmly adhered to concrete or plaster. There are two options here:

  • slow - arm yourself with a spatula or knife and, carefully prying the glued paper, finally clean the ceiling;
  • quick - buy a special attachment in the form of a metal brush for a drill and remove old wallpaper in a few minutes.

In either case, one should not forget about safety precautions. Safety glasses and a respirator will protect your eyes and lungs from the aggressive effects of dust, mostly consisting of lime. If you decide to work with a drill, then wait until the ceiling is completely dry, since turning on electricity with wet concrete can provoke a short circuit. Professional builders and finishers use a sander with interchangeable attachments instead of a drill to remove paper.

The last - the final stage of surface preparation after removing the old wallpaper from the ceiling - is dust removal. For this purpose, an ordinary household vacuum cleaner is suitable, but if the volume of work is large, then it is better to rent a special construction vacuum cleaner, which will cope with the task much better and faster. By the way, there will be much less dust removal work if you first cover the floor and large things in the apartment with protective film or paper. Compulsorily takes cover cushioned furniture (if there is no way to take it to another room). Otherwise, you will have to change the upholstery, as the old one will be soaked through with dust.

READ ALSO:

Well, if the house is built using the technology of monolithic reinforced concrete, then there will be no joints on the ceiling. It is more difficult when with ...

Therefore, there are often cases when the ceiling in a new building is not a smooth and even surface, but a series of small ...

Your question:

How do I remove old wallpaper from the ceiling?

Master answer:

If you decide to change the ceiling covering, then before starting work, you must clean it from old wallpaper.

Before removing the old coating, the ceiling is impregnated with a sponge hot water, after which the wallpaper can be easily removed with an ordinary spatula. If the ceiling is flat enough and does not require additional alignment, then the new wallpaper can be glued over the old layer, provided, of course, that the materials do not have overly contrasting colors that may appear on the new finish.

The described method is the most economical and widespread. However, if you want to execute quality repair, it is recommended to use new technologies and special tools that will not only clean the surface with high quality, but also greatly facilitate your work. At the same time, it is necessary to divide all the work into certain stages, each of which requires a separate careful approach.

Separately, it is necessary to highlight the preparation of the ceiling, which has already been thoroughly putty several times, painted or pasted over with wallpaper. In this situation, it is necessary to clean the ceiling to the very foundation, i.e. before brickwork or a concrete slab. Otherwise old finish may start to crack and damage new wallpaper. To facilitate this difficult work, a special puncher with a shovel or a card brush with a cutting machine will help. You can also use a drill with a special nozzle, which is especially convenient for removing old wallpaper.

After removing the old wallpaper, you need to clean the ceiling from dust using an industrial vacuum cleaner.

All work must be carried out in overalls that will protect your hands, eyes and respiratory organs from dirt, dust and other particles of the old coating that will fly from the ceiling during cleaning.

also old wallpaper can be removed chemically or thermally. But in this case, there is a risk of skin damage or poisoning, so if you resort to this option, then be sure to follow all safety measures.

You can start finishing the ceiling with a new coating immediately after completely removing the wallpaper, provided that the ceiling is even, the surface is dry and clean. Otherwise, all cracks must first be repaired and the surface must be leveled.

Hi everyone!
We continue to work on the ceiling. At the first stage, we washed off the old whitewash, removed the fragile layer of plaster and primed.
And today we will tell you about removing old wallpaper from the ceiling.

When decorating the ceiling, wallpaper is often used. But also like anyone construction material, the wallpaper has its own lifespan, after which it loses its original appearance. When you start renovating, the question of removing old wallpaper from the ceiling comes up.

All work on the repair of the ceiling must be done first, before the walls and floor are repaired. Installation of windows and doors is carried out both before and after the repair of the ceiling, at the discretion.
In order to avoid excessive dirt, all furniture (if any) and ceiling lamps should be covered with polyethylene or other covering material.

Also cover the floor with a covering material, then, after the repair, the working flooring should be carefully collected from the floor and thrown out along with the dirt. Do not forget about covering the surfaces of door blocks and window openings from splashes, since then they are poorly washed.

The temperature in the room during work must be at least +5 C.
Be sure to follow safety precautions. All electrical wiring in the repaired room (room) must be de-energized to avoid short circuits and accidents. Wear safety glasses. Put a hat on your head, if possible, work with gloves. Use only serviceable tools strictly for their intended purpose.
The following tools and materials are used to remove old wallpaper from the ceiling:

  • steel spatula
  • long nap roller
  • water or a solution of a special wallpaper remover
  • step ladder

There is a special solution as an alternative to water, when applied, removing old wallpaper is much easier. If you use special solutions, first carefully read the instructions for its use and the precautions when working with them.

Old wallpaper must be removed without residue. If the old wallpaper is two-layer or removable without residue in a dry state, then this does not require much effort. Just pry them off with a spatula and carefully remove them from the ceiling. If not, then the old wallpaper must be wetted with water or a special solution. Leave for a few minutes to get the wallpaper wet. After getting wet, old wallpaper is much easier to scrape off the surface with the same spatula. Sometimes it is difficult to remove even wet wallpaper, this is due to the fact that water does not soak all layers of old wallpaper. In this case, it is necessary to break the top layer of the wallpaper, scrape it with a sharp object, make notches, and give water access to the lower layers.

After removing the wallpaper, it is necessary to check the strength of the plaster, if any (tap the plastered areas). In case of insufficient strength, the plaster is removed from the ceiling surface.

Before applying the leveling layer (plaster, putty), the ceiling must be treated with reinforcing primers. To apply the primer, use a paint roller and a brush. The primer is applied evenly over the entire surface with a roller, in hard-to-reach places - with a brush. On highly absorbent substrates, apply the primer several times.

After removing old wallpaper and priming the ceiling, carefully pick up the debris from the floor or remove the covering material in a place with dirt.
Our advice: It is best to use warm water to wet the wallpaper.


Close