Do-it-yourself trailer for a walk-behind tractor from improvised materials. Homemade tipper trailer for motoblock fireworks Drawings and dimensions of factory trailers for motoblock

One of the most useful things in the garden is a walk-behind tractor. In addition, it is useful in the garden. With its help, you can easily cultivate land, as well as transport some goods: straw, vegetables, fruits, equipment, and the like. However, without a trailer it will not be possible to do all of the above. In this case, it is appropriate to tell you how to make a trolley for a walk-behind tractor with your own hands. This is the best way to save money. Also, for study, the topic "", with useful photos and video materials.

Drawings of homemade carts for walk-behind tractor

It is noteworthy that the made trolley will be able to carry a load weighing up to five hundred kilograms, as well as a driver. That's about seven full sacks of potatoes.

We present to your attention a drawing of the trolley:

1. Mounts for hanging devices walk-behind tractor (brackets).

2. cantilever beam

3. carrier

4. Footrest (from board 20)

5. Driver's seat

6. Main frame

7. body part

8. Support beam made of timber

9. M8- bolt

10. Thrust ring made of pipe

11. Stroller wheel.

The carrier is designed to hold only a few parts of the cart. They are fastened together by welding. Obviously, the most loaded part is the drawbar interface, as well as the turning part. Therefore, it is necessary to install stiffeners in this part of the structure.

Frame

The frame can be assembled from steel corners and pipes of round and rectangular cross section. At first glance, the design is very complex and has a large margin of safety. But it is worth noting that the transport will be used in difficult conditions. Therefore, all questions regarding strength disappear.

Drawing and dimensions of the trolley frame for walk-behind tractor

1. Slope from a metal corner.

2. Driver's seat frame

3. Riser made of pipe

4. Racks of the driver's seat, made of corner.

5,14. Pipe front braces

6,15. Longitudinal spars from the corner

7,8. Supports for wheel axles.

9,16. Rear struts made of pipes

10. Crossbar for reinforcement, made from a corner

11. Longitudinal joint housing

12. Wheel axle

13,17. Cross spars

18. Scarves.

However, if the loads are not so large-scale, then simpler structural solutions can be chosen (see).

trolley carrier

The wheel axle is made of a steel round billet with a diameter of 30 millimeters. If the axle length is one meter, then the wheels will be located under the body. The axle of the wheels with corner bearings, as well as a scarf, is welded together with the side members, as well as the body of the longitudinal hinge.

Body - dimensions and main parts

The body of the trolley is made of boards 20 mm thick. At the corners of the boards you need to fix the corners of steel. With the help of three beams, the body is attached to the bogie frame itself. Beams consist of a bar 50 by 50.

wheels

Wheels for the trolley can be used from a motorized stroller. The hub comes assembled. The ends of the axle must be sharpened so that they match the diameter of the bearings.

Spepka with a walk-behind tractor

With the help of a cantilever beam, the trolley is connected to the walk-behind tractor. The upper part of the console is similar to the contour of the holder. It is mounted in the bracket of attachments of the walk-behind tractor.

When the trolley is operated in difficult conditions, it is necessary that its connection to the walk-behind tractor be articulated.

The drawbar must be inserted into the tubular body of the hinge. The drawbar is fixed with a retaining ring. With the help of this design, it is possible to achieve independence of the wheels of the cart from the wheels of the walk-behind tractor. When driving with a loaded cart, this allows you to better control the walk-behind tractor.

Swivel assembly - diagram

1. Console;

2. Anthers;

3.6 Bearings (36206);

4. Housing;

5. Spacer sleeve;

7. Remote bushing;

9. Nut M20*2.5;

10. Oiler;

The driver will sit on a cushion that has medium hardness, because it is made of wood. The driver's seat is in front of the body. Management is carried out from the trolley. The operator's hands hold the handle of the walk-behind tractor.

Trolley design

A trolley of any design has the following parts:

Place for the driver;

Trolley with a body;

What material is suitable for the manufacture of the trolley frame?

It is best to prepare a frame for a cart from corners and a channel. They can be bought in almost any building hypermarket or at the base. It is important to cook the frame very carefully. The design must withstand movement with loads on difficult sections of roads.

Blank for wheel axle

For the wheel axle, you can use steel circles that have a diameter of 30 millimeters. The axis is connected to the longitudinal hinge by means of welding. It is important to choose such an axle so that the wheels are located under the body.

How to make a trolley body

You can independently make a body for a cart from boards that have a thickness of 20 millimeters. Steel corners are attached to the corners of the boards. With their help, the body is bolted to the frame. The best option is folding sides. So it will be possible to easily remove loads, as well as stack them on a wagon.

Wheels - what will fit

In principle, wheels can be taken from any agricultural machinery. In addition, some craftsmen use wheels from motorcycle equipment, as well as from strollers. That's just the axis will have to be machined to the diameter of the bearings.

trailer hitch

The hitch can be made from any piece of metal. It is necessary to drill a hole in it, which will be used for the hitch. The swivel assembly must be used with a bearing. It is important to strengthen it as firmly as possible by welding.

Trolley bottom

The bottom of the trolley can even be made from edged boards. However, it is best to use 2mm steel. The result is a trailer for a walk-behind tractor that can serve for several years without service. All materials for manufacturing can be easily found in any hardware store. The tool is sure to be found in every home. Is that electric welding can be rented.

When making a trailer for a walk-behind tractor with your own hands, it is important to consider that every detail must be made as accurately as possible. The quality and durability of the product depends on this. You can get the job done in just a few days.

Video examples of making homemade carts

Detailed video instructions for making a homemade cart, showing what and how to do.

Another example of high quality craftsmanship.

Equipment such as walk-behind tractors has long taken root among summer residents. Of course, this is an excellent assistant, which is designed to reduce labor intensity. earthworks. But it is difficult to underestimate the need for a quality trailer for a walk-behind tractor. It can be used for a variety of purposes, from transporting seedlings to crops or heavy tools. Let's talk about how to make a trailer for a walk-behind tractor with your own hands. Let's start from the very beginning.

About the characteristics and price of trailers

Before proceeding directly to the topic, I would like to consider a few basic characteristics inherent in any trailers for walk-behind tractors. First, it is their carrying capacity. It is impractical to make a trailer that cannot carry even 300 kilograms, so we will start from this minimum. As for the maximum carrying capacity, it should be no more than a ton. It is unlikely that the walk-behind tractor will drag more.

For example, an existing trailer for light walk-behind tractors with a carrying capacity of 300 kg and dimensions of 1 mx 0.85 cm costs about $ 200. If you take equipment for medium-sized walk-behind tractors, then their price rises to 250, and heavy - up to 500. Agree, the numbers are not small. Nevertheless, you can make a trailer for a walk-behind tractor with your own hands without any problems and at the same time you will not spend a lot of money. It is always necessary to start with the fact that a drawing is being drawn up. Let's do that.

We make a trailer for the Neva walk-behind tractor with our own hands: drawings and highlights

Most modern adapters for walk-behind tractors are made of galvanized steel. This solution is most appropriate, since the trailer will serve for a long time. The bottom is also recommended to be made of metal, it is an order of magnitude stronger - therefore, it will last longer. The drawings given in this article do not have to be used in the form in which they are submitted. You can sketch your own sketch with sizes and types of fasteners and use it.

But it is still recommended to use ready-made drawings of the main elements. These include the connecting frame, the body and the carrying carrier. You are probably wondering why this moment is so important. The thing is that you can make a trailer for the Neva walk-behind tractor without any problems with your own hands. The drawings also allow you to see the complex places of the structure, the methods of fastening and the places of attachment of various nodes. Believe me, it is much easier to think through everything at once than to redo it later.

From simple to complex

First, I would like to consider the simplest model in terms of manufacturing complexity. In order to start assembly work, we need the following material:

steel pipes with a section of 60x30, as well as 25x25 mm;
wheels and springs;
sheet steel with a thickness of at least 0.8 mm;
duralumin sheet with a thickness of at least 2 mm;
channel and fasteners.

It is not difficult to guess that you can not do without the appropriate tool. You will need a grinder, a jigsaw, welding machine and also a screwdriver.

The trailer frame in our case is a one-piece structure that is placed on a frame lattice. In order to properly equip it, we first make two traverses 25x25 mm, which will be the crossbars. Spars can be made from a 60x30 mm pipe. All elements are connected in such a way that eventually a lattice is obtained.

Continuing assembly work

After you have made the grate, two longitudinal pipes are welded to it, in the upper part of which a 25x25 mm strap is made and joined by welding. A do-it-yourself trailer for a walk-behind tractor, the photo of which you see in this article, has folding sides. This solution is most preferable, and for its implementation, the frames are made separately from the frame. Thin sheets of steel can be used as material for the sides.

Now we need to make a beam. To do this, you need two channels that are inserted into each other. One of the ends must be equipped with wheel axles. Now we need pre-prepared springs, with which we will connect the spar. To do this, the end of the springs is put on the axis of the earring and the axis of the beam, and the central part is welded with stepladders to the same beam. It remains to make a drawbar from pipes 60x30 mm. To do this, the pipes are joined and welded to the trailer, and the rear parts are welded to the spars.

We make a multifunctional trailer for the Zubr walk-behind tractor with our own hands

We have already figured out that before designing an adapter, it is necessary to draw up a drawing that will indicate the main dimensions and general form products. Next, you need to make sure that all the materials are in our required quantity. For hitching, we will use a channel, so they should also be stocked up. It is this stage that should be given special attention. The fact is that if you buy too many fasteners and rolled metal, then this is a waste of money, and not enough will entail redesigning the structure, which is not good.

I would like to note that a trailer made without the use of welding, that is, on self-tapping screws, will not last long, you must understand this. Therefore, borrow a welding machine from neighbors or friends for a while. To make a frame, you can take steel corners 50x25 and 40x40 mm. For the body, boards of 20 mm and a bar of 50x50 mm are suitable from which the support beams will be made.

Making the base of the trailer

A do-it-yourself dump trailer for a walk-behind tractor can be made according to the existing design scheme presented in this article. This trailer has 4 main units: wheels, carrier, frame and body. They are connected to each other by welding.

The body is almost completely wooden, assembled from 20 mm boards, the corners of which are reinforced with metal corners. The body is fastened to the trailer frame by 3 support beams (bars 50x50). Since we are presented with a single-axle design, it is extremely important that the center of gravity is shifted to the front, but does not go beyond the axle of the wheels. The disadvantage of this design is that the sides are not folding. But by slightly improving the trailer, this defect can be eliminated. It is advisable to make side loops. They are needed to secure the cargo during transportation.

Trailer running gear

This stage is one of the most important. The fact is that if the undercarriage is made incorrectly, then it is not necessary to count on the durability of such equipment. Therefore, pay special attention to this. What does not matter in our case is the wheels and springs. You don't have to buy new ones at all. Used wheels of any car are perfect, and you can buy second-hand springs from Moskvich.

In general, wheels from a motorcycle are suitable for assembly. It is desirable to remove them together with the hub. If the diameter of the rod and the hub bearing do not match, then the end of the rod must be sharpened. A good wheel axle can be obtained from a steel rod with a diameter of at least 30 mm. Its length should be such that the wheels do not protrude beyond the body rims. The connection of the rod with the trailer is carried out by welding through the corner supports to the spars.

The final part of the assembly work

It remains to connect the trailer and walk-behind tractor to each other. The console is used for this. It is desirable that it be attached to the bracket attachments. In this case, the rotary assembly of the carrier must rotate freely in its lower part.

The drawbar is inserted into the tubular body of the hinge. Fixing is best done with a thrust ring. This solution is the most preferable, as it provides independent movement of the wheels of the walk-behind tractor and the trailer. This is extremely important when driving on bumps.

Conclusion

So we assembled a dump truck trailer for a walk-behind tractor with our own hands. All that's left to do is secure the driver's seat and footrest. Management is carried out directly from the seat. If necessary, you can make a trailer with brakes for a walk-behind tractor with your own hands. True, this is not always necessary, since the connection described in this article does not provide for a large longitudinal movement, therefore, when the walk-behind tractor stops, the trailer will also become. That, in principle, is all on this topic. Now you know how to make a trailer. To do this, you will need a drawing, the necessary material and tools. And, of course, free time and desire. You do not need to be any mechanic or designer for this.

The use of a trailer for a walk-behind tractor allows you to significantly expand the functionality of this popular technical tool. However, the purchase of a finished device is not financially feasible for all homeowners. In such a situation, you can think about making a trailer with your own hands.

Types and features of structures

Trailers have different carrying capacities, and this is one of the criteria used in their classification. Most often, at home, there is no need to use devices with a high load capacity. Besides, all trailers for walk-behind tractors can be divided into groups according to their design:

Whole - have the most simple design, in which the bottom and walls are connected motionlessly.
With folding sides - great for transporting bulky goods.
Tipper - convenient during unloading and allows you to increase their productivity.

When planning to purchase a trailer or make a do-it-yourself cart for a walk-behind tractor, it is important to take into account some design features.

If everything is quite simple with one-piece trailers, then in the case of other types, this must be done. . Particular attention should be paid to the following factors:

Making a trailer with your own hands

After studying all the design options in the manufacture of a home-made trailer for a walk-behind tractor, the most simple options. A dumping device is certainly more difficult to make, but its functionality is an order of magnitude higher.

Do-it-yourself work on creating a towing device for a walk-behind tractor start with a drawing. Thanks to this, you can determine the amount of materials needed and select complex nodes that require the development of more accurate circuits.

It should be remembered that the center of gravity of a properly balanced trailer should be located closer to the front side, but at the same time not go beyond the level of the wheel axle.

Frame assembly

The reliability of the frame is determined by the durability and strength that the tow hitch will have. This should be taken into account when creating a project for a future towing device. Thus, in the manufacture of the trailer frame, the following materials can be used:

Is a pretty simple thing. Some homeowners decide to make more complex devices. In such a situation, all subsequent actions depend on the choice of a particular type of trailer:

On a tipper hitch, the tailgate must be hinged.
If it is planned to manufacture a trailer with folding sides, then all three sides, except for the front one, should have such a design.
Frames of folding elements should be made separately from the general frame. For simple models they may be its common elements.

Frame sheathing

This is one of the most simple steps in the creation of a towing device. However, some nuances are present and must be taken into account. To carry out work on the frame sheathing, it is worth choosing those materials that cannot increase the cost of the tow hitch:

First you need to sheathe the bottom (floor) of the trailer, and then deal with its sides.

Chassis

This structural element can be taken from an old vehicle, such as a garden wheelbarrow. An additional pipe is required for its fastening. The hub can be pressed on, and its rear part can be bored and strengthened on the axle. At the same time, it is extremely important to ensure that there are no distortions.

For mounting wheels the best option are the pins. They will provide a fairly reliable and long-term connection. Bolted connections can be used to strengthen structures. final stage work on the manufacture of the chassis will be the fastening of the caps.

After creating the towing device, it remains to make a hitch. This separate element, which is also very responsible. Most in a simple way the connection of the walk-behind tractor with the trailer is the "pipe in pipe" assembly. To one end in advance bent pipe a short piece of pipe is attached in a vertical position.

At the opposite end of the main element (curved pipe), a second segment is welded, and a kingpin must be fixed on it, which will act as a connecting element. This robust construction easy to manufacture and highly reliable.

One of the most necessary tools for every gardener, farmer or gardener who owns mechanized agricultural equipment is a trailer for a walk-behind tractor. Using a walk-behind tractor on the farm, you can plant, plow and cultivate. And if you attach a trailer to the walk-behind tractor, we will get an excellent assistant who can transport quite heavy loads. The dimensions of the trailer for a walk-behind tractor are calculated in such a way as to be a universal and multifunctional unit. They also facilitate the work of the farmer, due to the tilt of the body and the ability to open the tailgate.

The optimal dimensions of the trailer for a walk-behind tractor

Most trailers can be operated while seated thanks to the installed seat. Before choosing a trailer for a walk-behind tractor, it is necessary to check its compatibility with the walk-behind tractor itself. It is also necessary to take into account the strength of the frame and the thickness of the steel sheet, so that during the operation of the walk-behind tractor, the trailer does not deform.

Let's look at specific examples of what sizes trailers are.
Tipper trailer PM-0.6S. Trailer length 1400 mm. Trailer width 1000 mm. Load capacity 350 kg.

Motoblock trailer with springs 7C. Trailer length 2900 mm. Trailer width 1000 mm. Trailer height 1200 mm. Maximum load capacity 500 kg.

Homemade trailer for a walk-behind tractor. Trailer length 2250 mm. Trailer width 965 mm. Trailer height 885 mm. Load capacity 400 kg.

Trailer drawing for walk-behind tractor

This trailer can be used both with a walk-behind tractor and with a car, and is a transformed unit. Equipped with a simple sprung suspension.

One of the purposes of the trailer is the ability to transport a walk-behind tractor by car. The “Fork” knot allows one person to load and unload the walk-behind tractor without much physical effort.

With absence passenger car, the trailer is equipped with a body and connected to a walk-behind tractor. Instead of milling cutters, wheels are installed on the walk-behind tractor. The trailer has a good sprung suspension, thanks to which there is an excellent softness of the ride, good longitudinal stability and almost no rigidity. Parts of the trailer can be easily separated, which allows you to compactly store the trailer, in a disassembled state.

The length of the body is 2320 mm, the width is 1590 mm, and the height is 500 mm. Track width - 1490 mm. Body dimensions: length 1500 mm, width 1200 mm, height 300 mm. Fork size 500x300 mm.

Options

All parts by detail

Trailer options

trailer dimensions

The main purpose of the trailer is to transport cargo. The trailer itself is an intermediate link in the transportation of cargo. Therefore, the primary task when creating a trailer is to achieve low weight and good load capacity. All elements of the trailer design are rationally used. Chassis weight - 25 kg. The weight of the transported cargo is 200 kg. When stored, the trailer takes up very little space and fits easily into a car.

Equipment such as a walk-behind tractor is an excellent helper when working in the field, garden, cottage or farm. To expand the capabilities of the equipment, you can attach a trailer to it and transport soil, garbage, crops, tools and other heavy or bulky goods. You can make a trailer for a walk-behind tractor with your own hands, spending only a few days on it. The result is an indispensable assistant that will facilitate further work.

Preparatory work

First of all you need to consider what size the trailer should be so that it fits a specific walk-behind tractor, and it is convenient to use it. After that, you will need to sketch a drawing or sketch of the trolley, on which to display the structure from different angles, put down all the dimensions and draw the nodes.

Trailer mechanisms

You need to think through everything to the smallest detail so that during the assembly of equipment there are no difficulties. To do this, you need to figure out:

Having dealt with all these questions, you can start preparing list of necessary materials and calculation of the approximate cost of the future trailer.

A simple trailer for the Neva walk-behind tractor

To start making a trolley with your own hands, you need to prepare the following materials and tools:

duralumin sheet with a thickness of 2 mm;
sheets of steel with a thickness of 0.8 mm;
springs and wheels;
steel pipes 25x25 and 60x30 mm;
channel;
fasteners;
screwdriver;
welding machine;
jigsaw;
grinder.

trailer frame will be one piece mounted on a frame lattice. To make it, two traverses 25x25 mm must be made transverse and pipes 60x30 mm must be attached to them so that the result is a lattice.

To the finished grid welded two longitudinal pipes, on top of which a 25x25 mm harness is attached by welding. Sheets of steel, which are cut to the required dimensions and welded, will serve as the material for the sides.

The turn of the beam has come, for the manufacture of which two channels will be needed. The elements are inserted into each other, after which wheel axles are put on one of the ends of the resulting part.

The spar is connected with the help of springs, the end of which should be put on the axis of the beam and the axis of the earring. Then, the central part of the springs must be welded to the same beam with stepladders.

Lastly, do it yourself you need to make a drawbar from pipes 60x30 mm. They should be docked and, by welding, one part should be attached to the trailer, and the other to the side members.

A simple trailer for a walk-behind tractor is ready. I would like to note that experts recommend using a welding machine to connect its parts. Such a mount will allow you to operate the structure for a long time.

Do-it-yourself multifunctional trailer for a walk-behind tractor: stages of work, video instruction

Having decided on the dimensions and sketched out the drawing, how many should be calculated meters of rolled metal and how many channels will be needed to make a homemade trailer. This is necessary in order to protect yourself from unnecessary costs for the purchase of unnecessary parts and fasteners.

Required materials and tools:

welding machine;
steel corners 40x40 mm and 50x25 mm;
a bar measuring 50x50 mm;
boards 20 mm thick;
cutting of pipes of round and rectangular section;
wheels assembled with a hub.

future trailer will consist of four main nodes connected by welding.

Stages of work:

Trailer dump truck for walk-behind tractor is ready. Now you can attach the footrest and the driver's seat, from which the equipment will be controlled.

Homemade trailer for a walk-behind tractor from auto parts

Drawing up a drawing in advance and preparing necessary materials and tools, you can assemble such a trailer with your own hands in 1-2 days.

For work you will need:

front axle shafts from Zhiguli or Moskvich;
channel 65 mm along the length of the body;
corners 60x60 mm;
two pipes 2 m long;
one pipe 60x40 mm, 3-5 m long;
welding machine.

The load-bearing part of the structure will be axle, which is made from a channel. Its length depends on the length of the future trailer. On both sides of the channel, axle shafts from the car are joined by welding. Profile pipes are installed from above:

To ensure structural strength and rigidity, from the front corners of the bogie profile corners or pipes should be stretched. Joints can be bolted or welded.

The frame for the trailer is ready. Now you can install a simple wooden body made by yourself, a seat and attach it to the drawbar.

After watching the video instructions and studying the article, you can understand that in order to make a trailer for a walk-behind tractor with your own hands, you do not need to be a designer or a mechanic. To implement the plan, you need a drawing, necessary tools, materials and a little desire and free time.