The doorknob won't hold. Door handle repair: DIY step-by-step instructions. Repair when the handle falls out

Broken door handle, including on the entrance structure, is a common problem that can be easily dealt with on your own. There are several ways to fix a broken front door handle with your own hands, but first you need to establish the cause of the breakdown.

On the entrance structures, such variants of handles are installed as stationary (they simply serve as a handle), push (represent a lever that opens the lock when pressed) and rotary.

Stationary ones break due to weak fasteners or too much load, as well as due to mechanical damage.

If the handle on the front door, which belongs to the push or pivot model, is broken, then the cause of the breakdown is most often a malfunction of the mechanism. Since the causes and remedies for breakdowns are directly related, it is necessary to deal with the types of breakdowns. There are several options here:

1. When pressing (turning), resistance is felt, the handle is difficult to move. The cause of the malfunction in this case is most often the lack of lubrication in the lock or loosening of the fastening bolts.
2. After pressing (turning) the handle does not return to its original position. Such a breakdown occurs due to a malfunction of the return spring (it can fly off or burst).
3. The mount remains in the blade and the handle breaks off. This is due to deformation or displacement of the retaining ring.
4. The tongue wedges, stays in place when pressed (turned). This phenomenon is associated with a malfunction of the four-sided pin (square).

The latter problem can also be caused by several reasons.

Jammed tongue

If the tongue does not move, then the problem may be in an overly short square. Due to the unsuitable length, the pin moves freely in the mechanism and presses the latch, preventing it from working correctly.

Also the square can be broken. This phenomenon is not very frequent, and it is associated with the poor quality of the material from which the door handle is made. In such a situation, you will most likely have to change the mechanism completely.

How to disassemble the handle

Before you start repairing the front door handle, you must remove its mechanism. However, if the handle breaks off, then you do not have to remove it, it will only be enough to disassemble it.

Push-on design

To change the pressure model, no special tools are needed - just one screwdriver is enough. First you need to remove the decorative rosette, which can be screwed on from below with a small screw. The socket is removed through the handle. Then you need to unscrew all the other screws and screw ties on which the mechanism is attached. Now all that remains is to remove the handle and remove the mechanism.

If a structure is installed, which is one large pad (such products are often found on Chinese models), then it is removed differently. On the inside of the web under the cover, you need to unscrew the fastening screws (there are 2 of them), after which the handle is completely removed together with the cover, sometimes from both sides at once.

Swivel model

If the rotary model breaks down, then in addition to a screwdriver to dismantle such a product, you will need a thin metal object (awl, knitting needle, etc.). First you need to remove the decorative rosettes. A technological hole will open on the side. It is necessary to insert the sharp end of a thin metal object into it and move the pin back. After that, you can remove the handle and the entire broken mechanism.

How to remove

Repair of the door handle of the entrance door is carried out only after its removal. Depending on their shape (round or standard stationary bracket), such products are removed in different ways. The methods for each product are detailed below.

Round

Often round models are equipped with a turnkey locking mechanism on one side. This handle always comes with a special key with a stop for disassembling the mechanism.

You need to remove the round model from the side of the door where there is no hole for the key that closes the lock. Take a flat-bladed screwdriver and pry the decorative strip covering the fasteners with it, then remove the strip from the latches. Press the opened stopper with a special key, at the same time pull the handle, and it will be removed. Unscrew the 2 screws on the side of the removed handle with a suitable screwdriver (flat or Phillips, depending on the fastening) and remove the remaining halves of the handles on both sides of the door. Then remove the latch by unscrewing the screws that secure it.

Stationary

Removing the stationary model is easy. To do this, unscrew the fasteners with a screwdriver on which the handle is attached and remove it from the door. Moreover, the shape of the product does not really matter here: decorative round and handles - "staples" are removed in the same way.

Repairs

Repairing a door handle is primarily about eliminating the causes of breakage, so you must first identify the problem. The list of major breakdowns boils down to two: the entire mechanism does not fully function or the door does not open, although the handle is serviceable. If the handle is serviceable, then how to repair the door handle of the front door with your own hands is described in detail below.

If the stationary model looses, then the problem is solved simply: you need to tighten the fasteners (bolts or screws) that fix the handle, or simply change it.

If the handle is in good working order, but the door does not open, then this problem can be solved by removing the retaining ring and installing another. To do this, you need to remove the handle elements from the door according to the instructions above and simply replace this part with another.

If the handle is pressed or rotated with difficulty, the attempt to open the door is accompanied by the creak of parts, then you need to disassemble the handle and lubricate its elements with oil.

If the latch breaks, you will have to purchase another square. First, you need to completely disassemble the device, remove it from the door and replace the pin (square) with another one that is suitable in length.

When the handle does not fit into place, a spring replacement is required. To do this, you will need to remove the mechanism from the front door, remove the old spring and replace it with another one.

Replacement

If the mechanism cannot be repaired, then it is necessary to replace the front door handle with another one. To begin with, a latch is inserted into the end hole, which is screwed on with self-tapping screws from both sides. After installing the latch, it is required to clean the hole from construction debris. This can be done with a jet of air, such as a hairdryer.

Then the pin (square) is inserted into the corresponding square hole of the latch. A handle is attached to the pin on both sides. It is important not to confuse which side should be the left side of the handle, and which side should be the right. The correct opening of the door will depend on this. Then the handle is screwed to the door with self-tapping screws. Now all that remains is to mask the mounts. This can be done with decorative overlays.

How to open the door if the handle is broken

If the tongue is jammed, you just need to push it back. In this case, it will be possible to open the door quickly enough. To do this, you need to insert some thin durable object, such as a screwdriver, between the door and the latch, and then try to press on the tongue, pushing it inside the lock. This is not always easy to do, so if this is not possible, you can use another method: disassemble the handle on one side. Most often this is enough to remove the mechanism completely and open the door.

In order to establish the reasons for the breakdown of door handles, it is necessary to understand their main fundamental mechanisms. There are the following types of device:

Also, door handles can be classified by material of manufacture:

The main causes of breakdowns

Even door handles with the most durable and reliable mechanisms can break down. In order to understand how to fix a pen, you need to find out the reason: why did it break?

Repair rules for major breakdowns

In general, the repair of door handles is reduced to eliminating the causes of their breakdowns. Here are some of them.

1. If the handle breaks while the mount remains in place, in order to repair the handle, it is necessary to remove the rest of the handle from the door and replace the retaining ring with a new one.
2. In the event of a square breakage, it will be difficult to open the door, and unfortunately it is impossible to repair such a breakdown. This requires a complete replacement of the device.
3. To repair the breakage of the latch, you must completely disassemble the device. The short square is replaced with a longer one, which can be purchased at any specialty store. Further, the structure is installed in place, if everything is done correctly, you can open the door without effort. A strong square will serve you for a long time and regularly.
4. If the handle does not fit, it is necessary to disassemble the device and correct or replace the spring.
5. If pressing the handle is difficult and a squeak occurs, it is necessary to lubricate the metal parts by dripping oil. This breakdown is associated with clogging of the lock during its operation.

Steps for removing the door handle

For almost any breakdown, it is necessary to remove the door handle. Moreover, if it is not possible to open the door, dismantling is carried out only from one side.

This algorithm applies to door handles for interior and exterior doors. Sometimes the design can be slightly different. The screw is not located at the bottom of the handle, but on the inside of the door at the top or bottom of the trim. Moreover, the screw may not be one. With this design, by unscrewing both screws, you can remove the handle from both sides at the same time.

If you are repairing the door handle yourself, you must carefully examine the condition of the mechanism and the handle itself. In some cases, it is required to fix not only one breakdown, but several at once. If the handle is very worn out, it should be replaced with a new one. Moreover, the design of the new one must be identical. If it is not possible to open the front door on your own when the handle is pinched, you should contact a specialist.

On the front door, the vulnerable spot is the lock. If the installation of the entrance metal door is done correctly and during operation it was not subjected to abnormal loads, then the canvas itself will work for many years. But a lock with a handle is designed for a certain number of closing-opening cycles, and over time, this bunch of mechanisms fails. Most often, the cause of the malfunction lies in the fact that the handle is broken. If you look at its structure, then repairing the door handles of the entrance doors will seem like a trifling matter.

Of all types of door handles, push and stationary models are installed on the entrance doors. Rotary mechanisms are installed only on interior doors.

With the help of a lever handle, a person controls the opening of the canvas and simultaneously acts on the lock tongue, and with the help of a stationary handle, only performs opening and closing.

What usually breaks?

The stationary handle breaks down from mechanical damage (from impact) or from a loose mount. If the stationary handle is broken, it can be seen with the naked eye. In this case, it will have to be replaced. If the fasteners are loose, then they need to be tightened.

The lever handle, like any mechanism with moving parts, has weak points, the breakage of which leads to characteristic problems:

• The handle is connected to the fastening bar by a movable mechanism. Poor quality steel, poor riveting or excessive mechanical stress will cause the handle to fall out of the seat in the mounting bar. In such cases, it will not be possible to repair the mechanism, and you will have to buy a new one.
• A square rod is inserted into the socket at the base of the handle, hidden under the fastening strip, which transfers rotation to the lock and moves the tongue. If, when you press the lever, the mechanism works normally, but the lock tongue does not hide, then there is a problem with the metal rod. There can be two reasons: during installation, the rod was cut incorrectly and it became short (in a one-sided design). Over time, he could jump out of the hole in the lock case. The second reason is a broken rod due to poor-quality steel from which it is made.

Important! It is extremely rare that the seat at the end of the handle can wear out, and the rod can turn.

• The return to its original position after pressing is due to a spiral spring, which is fixed at one end on the fastening bar, the other at the end of the handle. If the spring breaks off or pops out of the mountings, then the spring effect will disappear. Repair of the door handle of an entrance metal or wooden door in this case is possible if the spring remains intact.

As you can see, there is nothing special to break in such a structure, and any master himself will be able to determine the cause of the breakdown and determine the way how to repair the mechanism. To do this, remove it and look under the mounting plate.

How to remove a push-type mechanism from an entrance door

Consider how a double-sided door push handle with a long fastening strip is removed:

• There are two fastening screws at the top and bottom of each mounting plate. Each screw on one side is connected to the screw on the opposite side of the door through a threaded sleeve (tie). To unscrew the fastening screws, it is necessary to fix the screw on one side of the door with one screwdriver, and turn the screw on the other side of the door leaf with the second screwdriver. So unscrew all four screws.
• We remove the handles with fastening strips from the square pin and inspect the rotary-return mechanism. We will repair the lost spring, check the mechanism for operability and fix it in place in the reverse order.

In this case, you will have to tinker in order to get the screws into the coupling.

The order of twisting the mechanism with a decorative strip:

• In this system, the handle is additionally fixed to the square bar by means of a small screw screwed flush in its lower part near the decorative strip itself. Use a thin hex wrench to loosen this screw. It is enough to make a few turns for the screw to come out of the engagement with the pin. It is not necessary to unscrew it completely.

Important! This screw is the reason why it is not possible to remove the handle with the decorative strip.

• Twist the decorative strip counterclockwise with our hands.
• Now the fastening screws will open, with which the strip is attached to the door leaf (or screws for the tie connecting two strips on opposite sides of the door leaf). We unscrew these screws and remove the handle from the square rod.

After that, we inspect the pivot mechanism and determine whether it is possible to fix the breakdown or whether the door handle needs to be replaced.

Replacing the handle on an entrance metal and wooden door is the same. The only difference is that when buying a new mechanism for a metal door leaf, its dimensions must exactly repeat the parameters of the old one. Its fastening holes, location on the keyhole fastening strip must completely coincide with the holes in the metal sheet.

What can you fix yourself?

On your own, you can perform the following handle repair:

• The handle falls out of the slot of the mounting plate if the retaining ring, which sits in the groove on its end, has fallen off. The ring flies off for two reasons: it is unclenched or burst. To determine whether the ring is whole or not, it is necessary to remove the fastening strip from the door leaf. In this case, the ring (or its fragments) will fall out. If the ring is intact, you can try bending it to increase the clamping force. After that, the handle is inserted into the hole of the mounting plate and the ring is put on. After checking the reliability of the fastening, the mechanism is installed in place. If the ring has burst, then it is unlikely to be replaced. In this case, you will need to replace the entire front door handle.
• If, after dismantling the fastening bar, it turned out that the square had burst, you can breathe: this breakdown must be repaired. Buying a new square is not a problem, only this time make sure that it is not silumin, but steel. Before installation, the square is cut with a grinder or hacksaw to the desired length, the ends are rolled with a file.
• If the latch does not work, find out if the reason lies in the length of the pin, or the return spring of the tongue inside the lock itself has fallen off. To do this, remove the mounting plate and use a screwdriver to check the operation of the tongue by turning the square slot in the lock case. If the tongue works, then you need to lengthen the pin. Better to buy a new one and cut it to the correct length. You can put linings (cardboard, wood chips) into the slot at the end of the handle so as not to allow the pin to go too deep into it and not fall out of the slot in the lock case.

• If the spring has fallen off and the mechanism does not return to its original position after pressing the lever, first it is also necessary to remove the fastening bar. The spring is attached under a retaining ring that holds all mechanisms in place. Therefore, you will have to remove the retaining ring and fix the spring. If it burst, then you can search and buy a new one. But usually in this case you will have to go to buy a new door handle for the front door.

Video on how to remove and repair the lever handle:

To remove the handle, check the integrity of its parts and determine the possibility of repair, you will need a screwdriver and no more than five minutes of time.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your ...

New articles

New comments

Artem

Assessment

Elena

Assessment

nezabudka-1

Assessment

Ekaterina

Assessment

Vladimir

Assessment

Latest reviews

adminadmin

We will send the material to you by e-mail

In the life of any person, a situation can happen when the latch fails due to the user's negligence or old age. Therefore, the question of how to fix a door handle remains very relevant. This is what the HomeMyHome editors will tell you about in detail today. As part of today's publication, you will learn about possible breakdowns and how to fix them.

If the lock inside the door has broken, do not rush to break it out, there are ways to eliminate the breakage
PHOTO: ps-resource.ru

It happens that locks stop working at or at the most unexpected moment. Finding a way to repair it is possible only by determining the type of malfunction.

If the mechanism is stuck

This problem occurs more often not because the core of the lock has failed, but the door itself has been incorrectly configured or not inserted into the box to the correct level. To determine what prevents the mechanism from closing correctly, you can on the open door by pressing the handle. If in this position the handle with the deadbolt works normally, then the reason is in the malfunction of the strike plate. The solution to the problem is as follows:

• tighten all the screws on the strips and the lock itself. Be sure to lubricate them with machine oil;
• if necessary, we adjust the door in the doorway.

If it's not a striking plate, then you need to do the following:

• grease the latch with WD-40;
• work with the mechanism;
• if it does not help, disassemble the door handle;
• loosen the locking screw slightly and reinstall the lock.

It happens that the lack of lubricant affects the performance of the door handle. A simple sprinkle of machine oil or other technical grease will help correct the seizure.

PHOTO: psk-remont.ru

The handle falls out of the door socket

The retaining ring, which is an indispensable part of the door lock, tends to pop out. You can observe this situation after blows on the door or a strong slam.

PHOTO: leroymerlin-catalog.biz

Such a ring can be inserted into place if it is intact. In case there are cracks or other defects, it changes. It can be purchased at a hardware store or simply replaced with a washer. If it does not fit a little in size, it is bent with pliers so that it presses the core well.

The door handle spring has broken

As a rule, such a small part needs to be replaced. Its breakage can be caused by careless handling of the door handle. To repair it, disassemble the fittings to the core, remove the upper washer and look at the condition of the spring.

PHOTO: remont-moroz.ru

It happens that it just jumps off and does not have any special defects. She is returned to her place. If there is any damage to the structure, it must be replaced. If the spring is difficult to remove from the grooves, then it is intact, and the breakdown is in another.

The lever does not come back after pressing

If the handle refuses to return, the malfunction may be due to dysfunction of the door handle return spring. To check this, you need to dismantle the fittings. To do this, remove the core from the socket and remove the spring from the inside.

PHOTO: 1obl.ru

After that, reinstall the new one and lock the stopper so that the spring stays inside.

There is no turning of the rod in the door handle

The problem of the lock can be associated with two factors: a licked milled square or a rod simply popped out of the core. To eliminate the cause, it is necessary to disassemble the structure. If a core defect is observed, then it is better to immediately replace it with a new one.

PHOTO: youla.ru

As for the licked square, you can temporarily wind electrical tape on the axis. This creates a more efficient engagement between the two parts.

What to do if the front door handle is broken: how to fix the problem

In fact, there is nothing complicated in repairing an iron door handle. If you use the right approach, you can fix the device in 10 minutes. It all depends on what type of handle needs adjustment.

PHOTO: remontidei.ru

We make repairs to the door handle of an entrance metal door

To proceed with disassembly, you need to have a hammer, Phillips and flat head screwdrivers, and some hex keys on hand. You will also need a drill and sandpaper. The peculiarity of this type of repair is as follows:

• you need to act carefully so as not to damage entire mechanisms;
• all parts must be folded into a deep box, preferably with a light bottom;
• in no case use a crowbar to remove the lock from the doors;
• it is also undesirable to use a screwdriver, since when unscrewing it can lick the screws.

On a note! If the handle is loose, this is one of the signs of an imminent breakdown. Therefore, it is necessary to tighten all existing bolts. To access them, remove the end ring on the round door handle.

PHOTO: zamokmaster24.ru

How to change the handle on a metal front door in stages

After the handle breaks on euro doors, you should carefully work with tools. After all, one careless movement can damage not only the core, but also open the door, if the handle is broken, it will be impossible.

How to remove an old handle from a door

As they say, breaking is not building, so the process of dismantling the handle can be considered elementary.

1. Remove the protective metal panel on the lock.
2. We unscrew the screws from the washer and remove it.
3. We take out the core and the square rod.

Often in the structures of metal doors there is a factory defect - a too short rod. Repair of the handles of the "Chinese" door in such cases is done using a more durable mechanism than before.

PHOTO: ivanovo.itwood.ru

Replacing the front door handle

If the rod becomes the cause of the malfunction, then new handles must also be purchased. It is important to choose them by the selection method, since the cross-sections of the handle hole and the rod itself may not correspond.

Interior doors and handle breakage: features of solving problems with the locking mechanism

Intensive impact on the mechanism of interior doors often disables the handles. The causes of malfunctions are usually the same as for the input structures. Only installation and dismantling can differ, since the device of the door handle of an interior door with and without a latch is not the same.

How to remove the door handle of an interior door

Replacing the handle of an interior door is performed in a few elementary steps.

Illustration	Action Description
	We start by examining the handle. We find on it a small recessed button. To press it, you must use any thin object. In the pressed position, we carefully try to pull out the handle. We pry off the handle cover, if it does not work, we unscrew it and remove it from the rod.
	We unscrew the bolts from the interior door that hold the round handle. We use a Phillips screwdriver for this. Only as a last resort we turn to a screwdriver for help. Now we remove the entire core from one side and the other.
	We unscrew the larva, for this we remove two bolts on the lock itself. We take out the mechanism.

How to disassemble the handle of an interior door depending on the type of mechanism

Interior door handles also have a wide range. Often the whole thing is not so much in the form, but rather in the working mechanism. Therefore, the analysis of the structure may have discrepancies.

PHOTO: domaster.ru

We dismantle the stationary and push handle

The stationary handle will last for years. It does not have any working mechanism, but only serves to open and close the door leaf. Usually it is connected by a common axis. The door handle can be screwed on from different sides. Removing such a device is easy.

Important! It is possible to remove the screws with a screwdriver only if the threads are coked and cannot be loosened with a screwdriver.

The lever handle is popular among others. In shape, it has the letter "G". When pressed, the latch plate enters the opening of the lock, after which the door opens. Such a mechanism closes without pressure. A similar design is disassembled by unscrewing all the screws and removing the inside. Dismantling is similar to disassembling the front door handle.

PHOTO: zamok-service31.ru

How to disassemble a round interior door handle

Round door handles of the interior door are fixed with special bolts or. It is enough just to unscrew them, and then remove the structure.

1. Open the door and turn the handle so that through a small hole you can see the inner button on the handle body.
2. We press on it with an awl, needle or hairpin.
3. Further, the handle body can be easily removed.

In case the handle won't turn, you can drill a hole with your own hands to press the button on the core.

PHOTO: ru.aliexpress.com

How to disassemble the handle in an interior door with a lock

In a house where a large family lives, from time to time you have to lock up, so knobs are often installed. They are dismantled in almost the same way as a round one without a lock. To fix the doorknob of an interior door, you need to do everything in stages.

1. We remove the protective ring or bar that hides the entire mechanism.
2. Next, you need to deactivate the stopper. It is located inside the protective element. For this, we use a special key or a millimeter hexagon.
3. While pressing the stopper, gently pull the handle towards ourselves so that it pops out of the mechanism.
4. If screws are provided in the design, they are unscrewed.
5. On the opposite side, we also remove the structure together with self-tapping screws.
6. After the fixing screws have been loosened, the handle with the core can be easily removed.

On a note!Conventional handles that have a thru-axle have a threaded mechanism. Therefore, in order to remove them, it is necessary to hold the handle on one side, and on the other, make turns.

PHOTO: yandex.uz

The specifics of repairing an interior door handle

All door components need to be replaced over time. The repair operations are exactly the same as for the entrance doors: greasing, tightening the bolts, changing the handle itself.

The entire troubleshooting process is best done in stages. It is important to put all the parts in the right place.

Elementary replacement of the interior door handle

After dismantling the old non-working structure, it is easy to insert the new handle. To do this, follow the step-by-step photo instructions.

Illustration	Action Description
	We insert the larva of the handle in the same place, if it matches in size. Using a screwdriver, screw in the self-tapping screws that will hold the latch.
	Unscrew the bolts shown in the photo. You will need them to hold the handles together after installation. We disassemble the opposite side of the handle, then remove the protective washer using the key that comes with the kit.
	We insert the disassembled, then insert the bolts. We screw them into the holes of the opposite handle. Align the holes on the handle and insert the handle until it clicks.

We check the performance of the structure. If everything is done correctly, not only the swing mechanism for opening will work, but also the latch-limiter.

How to fix an interior door lock if a foreign object gets inside

It happens that the door lock in the house is jammed precisely because of the ingress of debris, dust or other small objects. To fix this problem, you need a carpentry skill and some inventory: a screwdriver, pliers, screwdriver, grease, an old toothbrush, tweezers.

1. We disassemble the lock case and take out the cylinder from the door leaf.
2. We lay the structure on a light material so as not to lose details.
3. Checking how the mechanism works outside the door.
4. If something sticks, we lubricate and clean all contacting parts.
5. We examine whether a foreign object has got inside the lock.
6. If there is something, take it out with tweezers.

Further, if the structure has worked, we insert it into the door leaf, following the steps in reverse order, starting from the third point. For a more detailed acquaintance with the process, we recommend watching the video.

Castle. Built into the door leaf, it has a tongue and crossbars that are locked with a key. Now we are only interested in the tongue (dog), as the part directly affected by the handle;

Lever. By pressing it, the entire mechanism is activated (there are handles with a keyhole, the so-called knob handles);

Square pin (square)... Connects two handles together and transfers the rotary movement from them to the lock;

Decorative overlay... Hides the fastener and screws, performs an aesthetic function. It can be square and rounded. The handles on the bar do not have a decorative strip, since the bar itself is it;

Reply part... Installed on the door frame of wooden doors, it is extremely rare in metal doors. The tongue is included in the counterpart.

Problems and breakdowns of door handles.

The door handle is stuck.When you press the lever or rotate the round handle, you have to make additional efforts, press harder, pull the door towards you, or vice versa, press on it with your knee or shoulder.

The doorknob is loose or loose. - By pulling the handle, you can watch how it moves away from the door, the fastening screws become visible. There is a feeling that the lever is about to come off and remain in the hands.

The door handle does not return to its original position. - After pressing the handle, instead of returning it back, it remains at the lowest point. This pattern can be observed both with old pens and newly installed ones. The reason may lie not only in the handle, perhaps the lock drive is broken.

The tongue of the lock does not respond to pressing the handle. - The tongue goes inside the lock or, on the contrary, went inside and does not come out.

The door does not snap onto the lock pawl. - You have to slam the door hard or push it, or pull it on yourself.