Do-it-yourself wardrobe trunk for storing linen. Super budget storage ideas for underwear and socks. DIY kitchen organizer

Those who are madly in love with order in everything, including the linen drawer of their closet, simply cannot do without a linen organizer, in which each item occupies strictly its own cell. In the master class, we will show one of the options on how to sew a laundry organizer with your own hands.

The first thing we do is take measurements from the drawer where the underwear will be stored in order to build an organizer pattern. We got the dimensions of the box 75 cm long, 43 cm wide and 13 cm high.

In order to sew a laundry organizer, we need the following:

• blue thick fabric;
• thinner fabric of variegated colors;
• synthetic winterizer;
• white wide band for the edges.

Now we are going to sew a laundry organizer.

1. From a synthetic winterizer and a blue dense fabric, we cut out two rectangles, slightly smaller in size than the dimensions of the box. We made a cut 74 cm long and 42 wide so that the organizer does not deform.

We determine the length and number of cells of the laundry organizer, draw the blank.

Attaching large rectangular partitions, we will leave the edges 1 - 1.5 cm unsewn, we will need this in the future.

The time has come for the most painstaking work - we sew each small partition in turn on one side and the other. We recommend doing it manually.

And now back to the unstitched edges of the long partitions. We sew the two halves, steam, hide the seam inside and sew again

12. Next, sew the edges of the long partitions to the side walls, it is advisable to do it manually - this will turn out both neater and easier.

13. Let's take care of the outer corners of the laundry organizer. We trim them in height, cut off the protruding fabric, if any, and process the corner with a white ribbon. Do the same with the other three corners.

14. And now, finally, back to the large blue rectangle, cut and set aside at the very beginning. This blank will be the bottom of our laundry organizer. We carefully attach it to the padding polyester along the perimeter of the future product. You can sew with any of the seams, we used a zigzag so that the threads from the cuts do not interfere with further work.

Well, in the end, we will process the edges of the already finished bottom with white braid. Pre-sew the braid with a basting seam or pin it with pins so that it is evenly spaced, we pay special attention to the corners - they are the most difficult to work with. After making sure that the braid is located nicely and evenly, we attach it with a machine.

Organizer- an irreplaceable thing in the house for storing not only every little thing, but also some valuable things. Such a convenient and necessary little thing can be purchased at any supermarket.

Or you can turn on your imagination and do it yourself. And we will help you create an organizer for any occasion.

How to make an organizer with your own hands?

• Making a box for storing all sorts of things is not difficult even for a beginner. You will need material, stationery and a little time.
• Materials for organizers of things are usually created from improvised things, from things that go to waste or in rare cases, the necessary components are bought.

A small organizer for hairpins and elastic bands with your own hands for beginners

Surely, more than one girl has experienced the mess in her hair accessories. There are a lot of them, but they are not always in place. So, in order to put the elastic bands with hairpins in a decent order, you need to put them in one place. The place should be beautiful and comfortable.

You will need:

• Frame;
• ribbons;
• hooks;
• glue;
• scissors;
• ruler;
• cardboard.

Progress:

1. Measure your photo frame and cut the ribbons to size. Glue on the reverse side with a gap of 3 cm.
2. Then measure a sheet of cardboard and cut it to fit the photo frame, glue it over the ribbons on the back of the frame.
3. Glue the hooks on the outside of the frame, positioning as you please.
4. Now you can hang the photo frame on the wall or put it on the table.

DIY office organizer

To find a pen, some need to search the whole house and turn everything upside down. But if you have a stationery organizer, you won't have to go far looking for pencils and pens.

You will need:

• cardboard;
• pencil;
• tourniquet;
• 6 cans;
• paper;
• scissors;
• glue;
• paint in a can;
• ruler.

Progress:

1. Coat the jars with glue and cover with paper.
2. Make a handle as in the photo and wrap it with a tourniquet.
3. Then paint the jars and leave to dry.
4. Make the jars in pairs, inserting the handle in the middle, wrap everything with a tourniquet.

DIY underwear organizer: step by step instructions with photo examples

The creators of furniture for things did not think about how they would be stored there. And in most cases underwear suffers. Few people fold their laundry neatly at all times. Therefore, you can use a little trick and add a linen divider to the closet.

You need:

• shoe box;
• glue;
• scissors;
• ruler;
• stationery knife;
• pencil;
• paper for decoration.

Progress:

Measure the height of the cabinet where you want to place the organizer. Cut according to size.

Determine how many cells you need and measure them to fit the box. Cut out the partitions.

Checkout inner surface storage box.

Checkout appearance organizer.

You should end up with a beautifully decorated box on all sides.

Determine the size of the cells and make cutouts on the partitions on one side. The number of cuts affects the size of the cell, the more there are, the less storage space.

Decorate the partitions by pasting them with paper on all sides.

This is how easy it is to make a box for storing clothes.

DIY cosmetics organizer

Don't have time to buy a decent cosmetic bag for your beauty arsenal? Or do you have so much of it that the toilet bag is breaking? Then a magnetic board for cosmetics will help you.

You need:

• large photo frame;
• magnetic sheet according to the size of the photo frame;
• small magnets for each beauty item;
• paper for registration;
• glue;
• scissors;
• ruler.

Progress:

1. Measure the inner perimeter of the frame and cut the magnetic sheet along it.
2. Do the same with the design sheet.
3. Put a decor sheet in the frame, then a magnet and close everything with a frame lid.
4. Glue magnets to all makeup items.
5. hang on comfortable spot.
6. The organizer is ready, now you won't lose anything and everything will always be in one place.

How to make a handy jewelry organizer?

There are never too many decorations, you just need to find a capacious storage for them. A variety of boxes take up a lot of space, and besides, decorations are sometimes confused in them. Therefore, we offer you Alternative option to store jewelry.

You will need:

• frame;
• metal grid;
• pliers;
• paint in a can;
• furniture stapler and staples for it;
• hooks.

Master Class:

1. Place the mesh on the back of the frame and secure with a stapler. Trim off excess tails with pliers.
2. Turn the frame over and paint with paint, wait until it dries.
3. Hang hooks, and you can hang decorations on them. By the way, for some jewelry, hooks may not be needed.

Large shoe storage organizer

Storing shoes in boxes is not always convenient, and often it takes up a lot of space. So why not make one big shoe organizer?

You will need:

• plywood;
• electric jigsaw;
• roulette;
• pencil;
• wood glue;
• the bars are thin;
• self-tapping screws;
• sandpaper;
• iron rod;
• iron mechanisms for scrolling;
• dye;
• drill.

Progress:

1. Cut out circles from plywood sheets, choose the number of circles according to the number of pairs of shoes.
2. Finish the edges with sandpaper.
3. Cut out partitions from the bars for each section of the cabinet. Count that for one you need 6 pieces.
4. Make a hole in the center so that the cabinet turns.
5. Assemble the cabinet: plywood circle + crossbeams + plywood circle + iron mechanism and so on, repeating the steps.
6. Insert a rod through all departments.
7. Build a stand for the organizer and place the box on it.
8. Paint the organizer, wait for it to dry, and put your shoes inside.

Headphone organizer

Often the headphones are lying around and confused. This is very unpleasant and takes a fair amount of time to unravel. Therefore, we have prepared an interesting life hack for you so that your headphones are always in order.

Prepare:

• funny pictures 2 pcs;
• paper;
• glue;
• scissors;
• double sided tape.

Course of action:

1. Cut out the pictures.
2. Prepare a 5x10 piece of paper.
3. Fold the paper in half and glue the picture on each side.
4. From the inside at the top, secure with double-sided tape.
5. Now you can wind your headphones and not worry that they will get tangled.
6. You can replace paper with felt, and use buttons as fasteners.

Do-it-yourself organizer for small things: ideas with photos

To organize a trifle in one place, it is enough to create an interesting place to store it. Then she will always be at hand. A creative box will fit perfectly into your interior.

DIY folder organizer for papers and documents

Papers, like other work supplies, should be visible and in order. And so that they are always at hand and look good, build a storage folder yourself.

Required tools:

• colored paper;
• beer cardboard 2 pcs;
• glue;
• scissors;
• ruler;
• decorative paper.

Master Class:

• Cover the beer cardboard with paper for decoration.
• Cut sheets of paper 1 cm smaller on each side than beer cardboard.
• Using 2 long pieces of paper, make an accordion out of them. Bend 1 cm, and glue sheets through each span.
• Cut the paper for the crust and connect the cardboard, as in the picture in step 4.
• Glue the accordion with sheets. Your folder is ready, fold your papers.

DIY craft organizer

Craftswomen-needlewomen have a lot of gizmos that need to be stored somewhere. We suggest you make a box for small items.

You need:

• thick cardboard;
• glue;
• scissors;
• pencil.

Progress:

1. On a piece of paper, draw a future box in a folding form. Draw a handle on top for convenience. On the second sheet, make a drawing of exactly the same box.
2. Cut out the drawing, fold along the fold lines and glue.
3. Place them back to back and glue.
4. Design the box as you like and use it.

Try the option for storing ribbons and ribbons, for this box you will need:

• shoe box;
• eyelets;
• paper for registration;
• scissors;
• glue;
• pencil;
• ruler.

Progress:

• Cover the lid and box with paper for decoration.
• Mark points for future holes with a ruler and pencil.
• Attach eyelets.
• Lay the tape inside and thread through the holes.

DIY crib organizer

For young mothers, we have prepared a convenient organizer that can be hung on the crib. You can put the most necessary things for the baby in it.

You need:

• textile;
• scissors;
• ruler;
• threads;
• sewing machine;
• inlay;
• buttons or buttons.

Master Class:

1. Decide on the dimensions and cut the fabric according to them.
2. To seal the organizer, cut out exactly the same piece of fabric for the base, stuff your future organizer with a thin layer of synthetic winterizer and sew.
3. Make pockets of different sizes.
4. Make handles for fastening.
5. Sew along the edge of the trim, attach pockets and handles.
6. Make fasteners from buttons or buttons.
7. Your organizer is ready, use it to your health.

DIY kitchen organizer

The kitchen for every housewife is hers personal account a place where masterpieces are created. Therefore, in order to focus all the tools for creating unique things in one place, we have prepared two organizer options.

For the first option you need:

• adhesive wallpaper in 2 colors;
• cans of chips (pringles);
• scissors;
• tape measure.

Progress:

• Measure the diameter and length of the can and transfer the data to the wallpaper.
• Cut out the required size and glue the jar.
• Draw on the wallpaper of a different color a sign of the utensils that will be stored in the box.
• Cut out the sign and stick it on the jar.
• Put the organizer in a convenient place. Such storages can be made for each group of items.

The second version of the organizer is adapted for interesting storage of cups. For him you need:

• small boards;
• thick tourniquet;
• hooks;
• screws;
• screwdriver;
• staples;
• ruler;

Master Class:

• Connect all the boards with staples using a screwdriver.
• On the reverse side, make a mount and tie a tourniquet.
• Screw on the hooks.
• And write funny inscriptions with chalk to decorate the board.
• Hang the organizer on the wall and hang the cups.

Do-it-yourself car seat back organizer

Some families need car organizers, especially those with small children. Just for such families, we have prepared a master class on making a hanging box.

You will need:

• textile;
• scissors;
• sewing machine;
• threads;
• Velcro;
• inlay;
• straps;
• decor elements.

Progress:

• Measure the seat of the front seat and transfer to the fabric of the inside.
• Draw the pockets. Then cut out all the components.
• Sew the trim along the edge of the main fabric and onto the pockets at the top.
• Sew pockets and fastening straps.
• Attach decorative elements.
• Now your child will not be bored, and things will always be in one place.

Do-it-yourself organizer in the trunk of a car

Sometimes in the trunk everything is upside down. And it takes a lot of time to clean up. But there is an alternative - make a wardrobe for things in the trunk of your car yourself.

You will need:

• soft fabric;
• plywood sheets;
• self-tapping screw;
• screws;
• screwdriver;
• pencil;
• roulette;
• glue / sepler with staples.

Progress:

• Measure the dimensions of the trunk and transfer them to a sheet of plywood to make the bottom. Then make the same cover.
• Saw the partitions according to the required height.
• Insert one at a time and fasten with a screwdriver.
• Cover the cover with a fabric, preferably similar to the one in the car.
• Fasten it with a stapler or glue.
• Put an organizer in the trunk and fold things.

How to make a hanging bath organizer with your own hands?

An interesting organizer for the bathroom can be made from jars for storing cereals. To create something like this you will need:

• board;
• jars for storing cereals;
• screws;
• screwdriver;
• iron fasteners of a round shape;
• ruler;
• pencil.

Work process:

Mark the points on the board where the jars will be attached.

Attach jar holders.

Achieving perfect order in the closet can be difficult. Small things often cause confusion. The organizer will help to eliminate this problem - socks cannot get lost in it. You can purchase a special device in the store or make the product yourself. The manufacturing process does not require special skills and knowledge.

It doesn't take a lot of materials to make a sock organizer out of the box. This is a budget product for which you can use improvised means.

Necessary materials for the organizer:

Additionally, masking tape, cardboard or decorative elements (fabric, lace and satin ribbons) may be required. You can ask the seller for a box or look for it yourself in the backyards of stores. This secondary raw material is not of great value. If the drawer in the closet is large, then you can place several organizers in it at once. You can also take part of the box for personal hygiene items.

How to make a sock organizer out of a box?

From an ordinary cardboard box, you can make a convenient organizer for socks. Several are used to make different ways. This useful device does not require expensive materials, most of them can be found at home. Everyone will be able to cope with the work, because the process does not require special skills and knowledge. homemade device in no way inferior to the purchased Chinese counterpart.

Method 1

First you need to determine the dimensions of the box, which later will serve as a place to store the organizer for socks. Based on the parameters obtained, a box is selected. Ideally, the width and length of the cardboard product should be 1 cm less than the box. In the future, the cardboard frame will be pasted over with wallpaper, which will increase its thickness by several millimeters.

Method 2

My next brag is the underwear organizer!

If you have an Ikea nearby or you have the patience to wait for a package with an order, do not waste your nerves, effort and time on this “nonsense”.
I spent every evening on it for two weeks. Well, how I spent it - I sewed quietly, pricked my fingers with a needle, learned to work with a thimble, watched all sorts of films with one eye, drank tea, stroked cats ...
In general, sometimes I like the process itself more than the result achieved. And it’s also easier and faster for me to do something myself than to go and buy it. I remember somehow I tore my favorite brown-chocolate ankle tights, so while I got the same pair for a new pair, I already managed to make embroidery on the old ones. And I love them more and wear them more often than new)))
This is all to the fact that my perfectionism does not sleep and constantly spoils my mood - I love order in everything! I love it when every thing has its own place, when you close your eyes and without hesitation say in which drawer of the dresser is the piece of paper / colored pencils / charger from the old phone / pool cap that is needed right here and now. Oooooh, how crazy I am when I don’t find a thing in its place, or I find it, but where, by definition, it shouldn’t be there. Well, for example, the TV remote control buried among kitchen spatulas, openers and knives. And as for evil "burrowing" under mine hot hand it doesn’t turn out, and damned perfectionism doesn’t give me the endurance to leave everything as it is and poke the violator’s nose, I carry everything in its place…
Needless to say, every morning, when I opened my underwear drawer, I saw a bunch of women's things, absolutely not systematized. And it pissed me off again!

And then I saw HIM - an organizer!

And if in our town such a miracle was sold, I would buy it without hesitation! Well, or at least turned it in my hands and would understand the principle of assembly. Patamushta, when I, inspired by the idea, cut and began to sew, I “invented” the bicycle not the first time.
But if the hands are golden, it doesn’t matter where they grow from! If I haven’t beaten off the desire yet, I’ll tell you how this “miracle” happened to me.

First you need to take the dimensions from the box: length, width and depth (height).
My standard dresser drawer was 76 cm long, 43 wide, 13 high.

From a single-layer synthetic winterizer and the main fabric, I cut out one rectangle measuring 75 * 42
The dimensions of the rectangles must be specially reduced by one or two centimeters from the dimensions of the box, so that the organizer freely enters the box, does not shrink or bulge.
The blue rectangle can be put aside for now - we will need it at the very end.

And on the white (this is the base of the organizer) we sew long rectangles (these will be the walls of the cells). It's just that the blue organizer seemed boring to me, and I took another orange-white fabric.
The length of the rectangles is equal to the length of the base, and the width is equal to twice the height of the box (minus a couple of centimeters - again, so that nothing interferes with closing / opening). We sew the rectangles in the middle, fold the sides together, the seam is inside, and our partition turned out to be double - for additional rigidity and hiding all the seams and edges.
I sewed the outer walls of the organizer on the contrary - with a fold up.
I found the distance between the partitions empirically, folding bras in an optimized and ergonomic way in different ways and measuring the width.

The number and length of the cells also directly depends on the size of the bust of the hostess)) (here I have already drawn the boundaries).

No need to sew to the edge! Leave a centimeter and a half - then you will understand why.

Now it's a matter of small partitions. Have you determined the width? We add half a centimeter on each side for seam allowances, but on the contrary, we reduce the height by a centimeter. We also make double partitions - we sew such "bags" - as many as we have partitions. (I got 24 pieces). You should not cut everything at once in the same size - you need to periodically check the width between the long partitions (well, or initially sew them perfectly and accurately to the millimeter).
So, we sew the “bags”, turn them inside out. To make the corners turn out well, you can cut them off a little. And then all the details need to be steamed with an iron - this will turn out more evenly and accurately, and it will be easier to work.

We close the cut of the “pouch” with an oblique inlay or a ribbon folded in half.
Well, now we have, perhaps, the longest process of our creativity: sewing small partitions to large ones (along the lines marked in advance) from the beginning on one side, then on the other. This is where 90% of the time is spent.

Remember, we did not sew long partitions to the very edge? Now we sew both halves together along the short side (in height), turn it inside out, and steam it with an iron.

We close the upper sections with an oblique trim or ribbon. And from the sides along the edges we sew the walls-rectangles, fold up (as we did before on the long side).

We sew dangling long partitions to the side short wall.

We combine the sections of the side walls in height, stitch them, close the sections with an oblique trim or ribbon - this is the corner you get.

Well, now is the time to remember about the large rectangle, set aside at the very beginning. We put it on the bottom of our design and sew it around the perimeter (I stitched it in a “zigzag” so that the threads from the cuts would not interfere with further work).

Iiiiiii, the final stage - along the perimeter we close the sections with an oblique inlay or ribbon. Particular attention should be paid to the corners - so that nothing puffs up, so that no wrinkles!

Let's take it for a "fitting"!

And now the most pleasant part is putting everything in its place, admiring the perfect order and praising ourselves twice a day)))

But if passion is such a useful thing as you want, and laziness or pens are directed in the other direction, then ready-made laundry organizers, as well as shoe boxes, boxes for hats, vacuum bags and a million of all the things you need to organize the order of things, you can find!
You can also read about some ready-made organizers.

You can quickly and easily make an organizer out of a cardboard box. Choose the right size box to fit in your closet. You can use one or more shoe boxes. Paste with a cloth, for this use PVA glue. It will turn out very beautifully if you paste over the box with napkins using the decoupage technique.

Measure the length and width of the box, cut out strips 15-20 cm high from thick cardboard according to these dimensions. Cover the details with a cloth. Make a markup on them according to the size of the cells. Install the longitudinal partitions, fixing them on the bottom of the box with glue. On the crossbars, make cuts along the markings, not reaching the top 1 cm and put on their main strips. The organizer is ready.

In a chest of drawers, you can make a laundry organizer even faster. Cut out cardboard partitions to the size of the box in which you intend to store linen, dividing the storage space into cells with them. Cells can be of any shape: square, diamond-shaped, rectangular.

There are other variants of the laundry organizer based on drawer. Instead of partitions, you can put small boxes glued together. The cells can be multi-colored plastic mugs, jars connected to each other with glue.

hanging organizer

A hanging organizer made of fabric will help free up space in the closet. It's as easy to make as it is out of the box. You will need a dense fabric and material for pockets. Cut out a canvas of the desired size from a dense fabric and sew pockets on it. For overhead parts, you can use jeans pockets, multi-colored patches, transparent fabric. Sew the pockets in rows, then trim the product around the perimeter with a finishing tape. Throw the top of the organizer over the hanger bar and topstitch. You can hang this organizer for underwear on the door or outside on the end wall of the cabinet.