Do-it-yourself wooden country house. DIY small house. But there are also disadvantages

It doesn’t always make sense to build a permanent house on a summer cottage, suitable for living in both summer and winter. If the size of the plot is small, and the house itself will be used only for short-term recreation, then it makes sense to choose the option of a small, cute house. In addition to saving money, this will also significantly speed up construction.

Methods for constructing country houses

The labor intensity, price and time spent on construction greatly depend on the chosen material and size of the house.

The following construction methods can be used:

• brick construction. It is used mainly for medium-sized houses and is characterized by a fairly large investment of time. For a small house there is no particular point in using it;

• buildings made of monolithic concrete– practically not used, especially for small buildings;
• frame construction– can be called a universal technology, it is used both for the construction of small cabins and for the construction of large two-story houses;

• country houses made from block containers- allow you to eliminate the construction stage altogether, you only need to work with metal, cut holes for windows and doors.

Features of placing a country house

In relation to the development of the site, one should be guided by such standards as:

• SNiP 30-02-97 - issues of planning and location of individual buildings are considered, the project of a small country house is being prepared mainly taking into account this document;
• SP 11-106-97 – concerns the legal side of the issue (development, coordination, approval).

When locating a building, it is necessary to take into account fire safety requirements and sanitary and hygienic requirements.

Note! Fire distances should only be taken into account for houses located on different sites.

Fire clearances depend on the building material used. So, if a house is built of stone and reinforced concrete, then the minimum distance between houses on neighboring plots should be 6 m. But in the case of a frame house using low-flammable building materials, this distance increases to 10.0 m.

As for sanitary and hygienic standards, even a small country house must be located at the required distance, for example, from a cesspool, compost heap, well, outbuildings, etc. For example, the distance to the restroom should be at least 12.0 m, and to the bathhouse or shower - 8.0 m.

Frame construction

Briefly, this technology can be described as follows: a building frame is created from beams and wooden planks, then the frame is sheathed. After this, only the interior and exterior decoration remains. Moreover, the technology does not change much, regardless of whether a small cottage or a large building is being built.

What should the foundation be?

Since the load on it will be minimal, you won’t even need a strip foundation. Its role is not to carry a significant load, but rather to raise the structure above ground level. This must be done in order to protect the tree from rotting.

For small buildings, a columnar foundation can be made not even from concrete or brick columns, but from wooden beams dug into the ground. Of course, the durability of such a structure is lower than that of concrete or brick, but the price of such a foundation is minimal.

Note! In this case, the part of the column located in the ground must be impregnated with protective compounds and wrapped in waterproofing material.

Installation of lower rails

Small country houses weigh very little, so if the bottom frame is not securely fastened, the structure can easily slide off it, for example, in a strong wind.

You can go two ways:

• use anchor bolts;
• leave reinforcement outlets in the concrete of the columnar foundation itself. Then you will need to make a hole in the beam equal to the diameter of the reinforcement and simply put the beam on it. The excess metal is simply cut off. This method is useful because the beams can be easily replaced during repairs; you just need to raise the houses above them.

As for the corners, the bars are connected to each other “in a paw”; there is no point in messing around with more complex options. For additional strength, both beams are connected with wooden dowels. Floor joists are laid.

Frame installation

The frame for a small country house is made of beams (10x15, 15x15 or 10x10 cm) - installed in the corners, the top trim is also made from them, wooden planks (4x10 cm) - suitable for logs, rafters and floor beams, as well as wooden planks ( for example, 8x3 cm) - for frame posts.

The installation instructions look like this:

• racks made of beams are installed in the corners; for greater strength, they are put on the dowel connecting the beams of the lower frame. Additionally, they can be fixed with metal corners;

• racks can be attached to the lower frame either only with metal corners, or by complete or incomplete cutting;

• the bars of the upper trim give rigidity to the structure;
• floor beams are laid;

• the rafter system is installed;
• The frame is being covered.

Note! The frame posts are fixed with temporary braces during construction, then they are removed and permanent braces are installed.

Separately, it is worth mentioning the roof. Since the load on the rafter system will be small, you can use a hanging rafter system.

In this case, the load will be transferred to the walls of the house. The crossbar is responsible for the rigidity of the rafter frame.

Container houses

Ordinary shipping containers can be turned into beautiful small cottages. In this case, the size of the building is limited by the size of the container itself; if desired, several containers can be combined at once.

All work in this case comes down to transporting the container and its external and internal decoration. When upgrading an ordinary container, it is enough to simply cut holes in the metal for windows and doors, while the metal must be left in the corners, otherwise the rigidity of the structure will be insufficient. If there are problems with the power supply on the site, then renting a diesel generator for the dacha will help.

The inside of the house will definitely need to be insulated. This must be done even if you plan to stay exclusively in warm weather. The fact is that the heat insulator is also a good sound insulator.

The frame for insulation is assembled from wooden blocks, and the space between them is filled with any suitable material, there are no special restrictions. You can use polystyrene foam, mineral wool, mineral wool boards, etc.

Note! The container can easily be stolen; to prevent this from happening, it is advisable to weld its lower part to the foundation posts.

The result is a building quite suitable for living. As for the size, even the smallest country house is quite capable of providing a comfortable overnight stay for 2-4 people; for the average family this is quite enough.

Summarizing

There is a small house on almost every summer cottage. Every summer resident can build a small country house with his own hands, and the information in this article will help you decide on the optimal construction technology. The main attention is paid to frame technology, as the most promising for solving this kind of problems ().

The video in this article shows the process of building a small country house.

Owning a country plot gives you the opportunity to fully enjoy the fruits of your dacha labor and get some relaxation at a fragrant barbecue festival. But what is a plot without any building on it. And if there are no funds for capital construction, then you can build economy class country houses photo, which will become a seasonal haven for vacationers or those working in the country, and will also serve as storage for all gardening equipment.

Read about what is cheaper to build a garden house from and how to do all the work correctly in our material below.

Materials for the construction of an inexpensive country house

To understand what you can save on when building a country house, and how to build a cheap country house, you need to study all possible options for building materials. So, you can build an inexpensive cottage with your own hands from the following materials:

• Frame-panel fragments. Here, timber is used to install the frame, and chipboard, fiberboard, OSB, etc. slabs can be used as cladding. To insulate such a house (if desired), you can use polystyrene or mineral wool slabs. As a result, the house can be used not only in the warm season, but also in winter. A special feature of the installation of such a frame-panel house is its undeniable savings. After all, it is fashionable to assemble a building using practically available materials, of which every summer resident/gardener/craftsman probably has a lot. As a last resort, you can borrow leftover material from your neighbors.
• A log house can also be made in a country house. Such construction will cost a little more, but the house will be stronger and more durable. The only drawback of wood (especially if the cheapest planed timber is used) is that it shrinks. As a result, cracks and gaps appear in the walls. It will be necessary to additionally insulate the building so that the country cottage can be used without problems.
• In response to the question of how to build a cheap dacha, we can advise building clay building. That is, to make a kind of adobe house. The construction technology is simple and similar to modeling. Materials for installation will cost the craftsman practically nothing, since the clay and straw from which an adobe house is built is practically underfoot. Such a clay country house, if all installation rules are properly followed, can become a durable building for any season. The only drawback of an adobe house is that its construction will take a lot of time. Perhaps even more than one season.
• Caravan house. This option for setting up an inexpensive country cottage is the simplest. You can find a more or less decent trailer that is simply installed on the site. If desired, water and sewerage are supplied to such a trailer.

Important: for any type of inexpensive country house, you can install lightweight types of foundations - pile or shallow strip foundations. And this is an additional point of savings during construction.

Frame-panel house: technology of work

To build such a house using frame technology, you will need to prepare material in accordance with the given perimeter of the building. The materials you will need are:

• Beam with a section of 100x100 to create the frame of the house;
• Self-tapping screws and metal corners for fastening frame posts;
• Panels or slabs of fiberboard, chipboard, OSB;
• Insulation material (if desired);
• Piles for the foundation and a metal channel for tying the piles.

We carry out the work in this way:

• It is worth installing driven piles in the designated places in the corners of the future house. Supports are also installed under wall joints and under load-bearing partitions, if any are included in the house design. Monolithic concrete pillars and brick supports can also be installed as supports. In any case, the pillars are mounted on a sand cushion to a depth of at least 60 cm. In this case, both concrete and brickwork should be reinforced.
• The finished supports are tied with a channel or I-beam, and waterproofing material is laid over the pillars.
• Then a timber sheathing is laid on the resulting belt, which will become the base plate of the frame. That is, the timber should lie along the perimeter, and wooden logs should be placed on top of the timber frame in increments of 50-60 cm. All wooden elements are securely fastened together with metal corners and self-tapping screws.
• Now it’s the turn of the vertical timber racks. They are mounted in increments of 50 cm, firmly resting against the timber frame. For additional fixation of the longitudinal supports, jibs are installed on each side. You can also install crossbars.

Advice: it is better to assemble the frame on the ground in parts, and only then lift it and fix it to the base.

• Once the entire frame is ready, the top trim of the vertical posts is completed. And attic or floor joists are laid on top of the upper belt.
• The finished frame is sheathed with selected panels, securely fixing them and leaving space for window and door openings.
• The top of the house is sheathed with any insulating material, not forgetting to install vapor and waterproofing materials.
• For exterior finishing, you can choose corrugated sheets or siding.

Important: in order to further save on the construction of a summer house, the roof is made pitched and covered with lightweight roofing materials.

• You can save additional money by installing simple wooden window frames and doors. This is how you can quickly build a house.

Timber country house

In this case, the work will be performed in a different sequence. First of all, you should prepare the following material:

• Beam of any section. But it is worth remembering that the larger the cross-section of the material, the stronger the finished house will be.
• Wooden dowels made of hardwood.
• Roofing material.
• Floor board.

The work is carried out in this way:

• First, the foundation is laid. It can be either a shallow strip (40-60 cm in height, including the base) or a columnar/pile type. But in any case, the concrete must dry well, and its top and all other sides must be properly waterproofed.
• A backing board made of moisture-resistant wood is laid on top of the foundation. In this case, the board is fixed to the foundation with construction anchors, deepening them 15-20 cm into the base.
• After this, they begin laying the timber, joining it at the corners into a bowl. That is, you will have to do additional work, forming grooves for laying the timber.

Important: each crown must be controlled horizontally.

• After 2-3 rows of crowns, the timber is additionally fixed with construction dowels. To do this, holes are drilled to the full height of the three stacked crowns and arranged in a checkerboard pattern. Pins are stuffed into the holes. It is worth remembering that next time the dowels need to be shifted relative to those already mounted below.
• The fully assembled walls are covered with floor beams, cutting them into the upper crown. The beams are laid in increments of 40-60 cm, and then covered with a floorboard.

Important: the same principle applies to the flooring in the house. If desired, both the upper and lower floors can be insulated with mineral wool or polystyrene slabs.

• The roof of a finished timber house can also be made pitched in order to save money.

Advice: a house made of timber needs about six months to a year to shrink. It is recommended to cut window and door openings after the wood has settled. Otherwise, the house may suffer greatly.

House made of clay

If you don’t know what to build a dacha from, then try installing an environmentally friendly adobe house in your dacha. You'll have to tinker here. The fact is that to construct such a structure, a large volume of clay and straw should be prepared in advance in the summer. It is these components that will become the main ones in the construction of a cheap house.

• So, after the clay has rested for the winter, it can be used. To do this, clay is loaded into a specially prepared pit and moistened with water in an amount of 20% of the total mass of the material. Cut straw moistened with water is also added here. The straw cutting length should be 9-16 cm.
• The whole mass is thoroughly mixed. You can use your feet. And to make the adobe mixture stronger, you can add lime to the solution. It will strengthen the strength of the finished house.
• The mass is left overnight, and in the morning adobe blocks are made from it. To do this, the mixture is compacted into a specially prepared form, cutting off the top of the mixture with fishing line or wire. Five holes are made in the blocks so that moisture can freely leave the brick.
• The finished blocks are knocked out and laid on a platform in the sun, arranged at an angle.
• After two to three hours, the blocks can be transferred to the shade and left on edge until completely dry.
• In this way, you should prepare a sufficient amount of adobe bricks.
• The construction of the house is carried out on a pre-laid foundation. The masonry is carried out according to the principle of brickwork. And the same clay mass is used as a solution. The width of the seam in this case should be no more than 1 cm.

Important: you need to lay adobe blocks no more than two rows per day. This is necessary so that the adobe mixture can dry thoroughly. At night, the rows of masonry are covered with film.

• Once the walls of the adobe house are ready, they can be plastered outside and inside.
• The floor in such a house is made on the ground, first laying waterproofing, and then laying joists and insulation between them.
• The roof of an adobe house can be anything, but it is important to make good projections (at least 70 cm) so that moisture from rain or snow does not spoil the clay walls. When installing windows in an adobe house, it is worth making canopies over the frames and ebbs in the area of ​​the window sills. A house built in this way will serve the family for decades.

Caravan house

The simplest type of country house for a seasonal stay, as an answer to the question of how to build a country house. Moreover, the trailer can be installed simply on brick pedestals-supports, installed simply on a sand cushion. There should be one support post per meter of trailer length. If desired, the trailer can be insulated, and then such a country house will become cozy in winter.

Remember: you can build a country house with your own hands from any material, the main thing is to comply with all the basic requirements for each type of raw material used.

If you have recently purchased a summer cottage, then the issue of building a small country house is very relevant for you. You can store household items, expensive tools in it, as well as create a small lounge and kitchen. In this article we will look at how to make construction of a country house inexpensively with your own hands, and also find out which materials you can save a lot on.

Construction of a country house inexpensively with your own hands

Of course, like any construction, it also needs to start with calculating the budget. How much money are you willing to spend on this project? If enough, then you can think about building a brick house. Otherwise, it is recommended to use borrowed frame house technology. The advantages of this method are obvious - saving money, as well as the efficiency of the work performed. In just a couple of weeks your house will be ready for use.

Stages of construction of a country house:

Creating a project. If you do not want to contact a specialized agency, then you can create your own project that will be convenient for you personally. The main thing that you have to do in any case is to show your finished project to professionals in order to avoid possible problems in the future. As for the area of ​​the future home, it all depends on your personal preferences and capabilities. 40 sq.m. is quite enough.

Purchase of building materials. What materials are needed to build a country house with your own hands? Today the market offers a huge variety of high-quality, efficient and durable materials that are suitable for any construction:

• Log or beam. Wood will be needed in any case. Depending on the quality of the raw materials, the cost of the timber will fluctuate. Carefully inspect the material; it is important that it is thoroughly dried.
• Brick or cinder block. They have low cost, durability and reliability. Although building a house using these materials will not greatly affect costs, be prepared to spend a significant amount on subsequent wall finishing.
• SIP panels. High-quality, modern materials that not only save your money, but also time. A house made from SIP panels is warm, dry and comfortable.

Important! If you want to save money on materials, study the market thoroughly. You will be able to find high-quality raw materials at a big discount. You should not focus on branded companies, since they are the ones who mark up more than 50% on the price.

Where to start building a country house on a summer cottage?

The most important element of any country house is the foundation. The service life of the structure, its reliability and strength depend on it. Of course, the foundation should not be neglected, since any mistake or wrong action will immediately result in cracks and splits in the walls. Before digging a trench for the foundation, carefully calculate the weight of future materials - walls, roofing, sheathing, insulation and finishing. All this adds kilograms. Typically, the depth of the foundation of a house should be at least 1 m. After pouring, it must be left for a month to compact and dry.

Immediately after the foundation, you can begin building the frame and installing the roof truss system. It is also worth considering high-quality sewerage. If there is a central sewer system, then you should buy a septic tank with outlets to the irrigation fields.

So, is it possible to build a country house? inexpensively with your own hands? Certainly. The main thing is to plan and not rush to buy materials from the first person you meet.

See also video:

DIY garden cottage

Do-it-yourself summer houses for relaxation

Most summer residents live outside the city only in the summer and do not need expensive permanent homes. They want a roof over their heads and living space large enough to accommodate family members.

How to build a house with your own hands?

An optimal economic pension is best suited for this purpose.

Advantages of summer cottages

House boards are popular due to the following advantages:

• High level of construction - 2-6 weeks
• Low cost - from 3 to 8 thousand rubles per square meter. m versus 18 thousand rubles. per square meter. m for houses with brick walls
• Low weight, allowing the use of cheap, shallow foundations
• Resistance to freezing forces
• The ability to manufacture parts at the factory, which improves the quality of construction and simplifies assembly
• No shrinkage
• Wide range of architectural solutions
• Ability to warm up and adapt at home for life

Panel house design

The house consists of a wooden or metal frame covered with panels.

The metal frame is made of a rectangular cross-section, and the wooden frame is made of a rod. For external coatings:

• Lamels
• OSB panels
• Profiled film
• Moisture resistant plates
• Asbestos cement slabs
• toilet

The inner leather is made of moisture-resistant materials.

If the house is to be lived in all year round, the walls are lined with insulation.

Construction of panel houses

Construction companies offer services for the construction of turnkey panel holiday homes or a set of parts for their own construction. The first option frees the builder from most of the problems, while the other allows you to build a house for your dacha and save money.

Project selection

A quality project is the basis for success in building a house.

Serious companies that produce panel houses and key building kits offer dozens of standard models and offer custom design services.

Individual projects are quite expensive, so they are rarely used for economy-class houses.

Creating a standard project allows you to save on design and a wide selection of already prepared architectural solutions - choose the desired design and location of the house.

foundations

Under the light panel house, spacers and notches are used with columns and strips and screw pilots.

• Small hidden pillars reduce costs and shorten construction time.

  Columns are installed at intervals of 1.5 to 3 meters under external walls and columns, at the corners of the building and in places where internal walls connect to external walls. They are made from logs, concrete, red brick, bentonite and base blocks. The depth of the coating is up to 40 cm, the cross-section should exceed the thickness of the walls. To increase stability, the columns are connected to wooden or reinforced concrete beams

• Countertops do not allow for a warm basement.

  If the design is included in the design, a shallow recessed base underlay is applied under the exterior walls and a foundation base is provided under the interior walls. The depth of coverage and width of the tape are the same as for pillars. The belt is made from concrete, quarries or foundation blocks

• On weak floors it is based on screwdrivers.

  Using them allows the house to rest on solid ground that is deeper than the surface. Helicopter bases can be built in 1 to 2 days without the use of heavy equipment

frame

The panel of a prefabricated house can be made from a kit made in a factory or from purchased materials, in-house or from a contractor.

Turnkey construction of a house eliminates most of the problems for the developer, with the exception of monitoring the execution of construction work - it is impossible to check the quality of the frame assembly on its surface.

To self-assemble the frame from factory parts, you must follow the instructions and wiring diagram included with the kit.

The work resembles a design meeting and is entirely possible for a developer with experience in construction.

The cheapest, but most worrisome option is to build the lumber itself. Depending on the size and number of floors of the house, the frame is made of a rod 100x100 - 150x150 mm or 50 mm thick.

The frame is installed in the following order:

1. At the top of the base there is waterproofing of the roofing material
2. For the foundation using built-in parts and anchor bolts to attach the frame (thresholds) - beams, it is located at the edge of the house and under the prairie
3. Place logs and give rough soil.

   Fits on the edges of the base or beam beam

4. Install vertical skeleton posts - first on the corners and then on the walls of the 0.6 m shelf, installed on the cutout, sawn in the bottom panel, securing the clamp and nails and securing the first temporary and then permanent remainder.

   At the same time, they constantly control their verticality and position in the same plane. The corner posts are made of sticks and you can use the same 50mm width edge plate for intermediate use

5. In the upper places the top tape works. Framed door and window openings

All wooden structures must be impregnated with antiseptic compounds.

Overlapping and covering

Wooden columns are placed on the top frame of the frame and secured using structural clamps.

Width 3-4 meters - plate size 50x150 mm with a large range - 100x150-150x150 mm. The beam is 0.6 m. In this case, 1.8 m wide screens (modules) are used to cover the ceiling.

Rafting clusters are made on the floor on a panel 50x120-50x150 m.

First install the outer rafts, and then the intermediate elements that control the position of the rafters in one plane. Then make a box and close the roof. Roofing materials for a home should be light, for example:

• Bituminous shingles
• Metal panel
• Profiled film
• Bituminous slate

Wall coverings

The width of the screens should be equal to the degree of installation of the frame rails and the length to the height of the walls.

Security guards are on offer at the workplace in the following order:

1. Plates assembled
2. On the frame there was a polyethylene film as a vapor barrier
3. Guide the inner frame frame
4. Frame facing, heater inserted inside
5. Wind resistant protective membrane
6. Get outer skin

The coat should be compressed over the frame by half the width of the frame frame to hide them.

The perimeter protection frame is covered with a heater and is tightly inserted between the frame frames. Application is done using nails. When using sheet material, it may be without a frame. The cutting blades are attached directly to the frame and the heater is inserted between the posts.

As can be seen from the description, the construction of a country house with a team of two or three people of average qualification.

Using factory modules significantly speeds up assembly. In just a few weeks after you start installing the frame, you can move into your cottage and enjoy the outdoors.

Videos on weekends

Simple holiday home

How to insulate a plate with your own hands in front of a path

Country houses made of foam blocks: building a house over the summer

Country houses made of foam blocks are lightweight and fireproof.

Thanks to the large dimensions of the blocks and precise dimensions, construction is carried out at high speed. It is quite possible to build a house over the summer.

The use of foam blocks in the construction of various structures guarantees heat conservation and fast pace of work. A country house made of this material will cost more than one made of wood, but less than one made of brick.

What are the benefits of foam blocks?

• They have a precise geometric shape and the dimensions are well maintained.

  Therefore, they can be installed quickly

• Moisture resistant
• Inexpensive
• Strength increases over time
• They have very low thermal conductivity.

  According to this indicator, it is one of the best materials for construction.

• They have a small specific gravity. Therefore, they are manufactured in fairly large sizes, which has a positive effect on the speed of wall construction
• Easy to handle

But there are also disadvantages

• Cannot bear heavy loads
• Slowly gaining strength.

  In this case, shrinkage occurs.

  DIY country house 6x6. Photo report. Part 1

  And as a result, cracks may occur.

Use high-quality autoclaved foam concrete - it is less susceptible to shrinkage.

For the construction of one-story country houses, the strength of foam concrete is quite sufficient. In this case, it is necessary to strengthen the upper load-bearing row with reinforcement.

Foundation

Usually, when building a country house, a shallow strip foundation is used.

It can be done in different ways.

• From prefabricated blocks laid without connection, freely
• Made from blocks, with reinforced belts installed above and below the blocks
• Made from rigidly connected reinforced concrete blocks
• Made from monolithic reinforced concrete

The choice of method is made depending on the properties of the soil.

The reinforced tape option is suitable for both subsidence and highly heaving soils. The width of the tape is made to exceed the thickness of the walls by 10-20 cm. Laying depth is up to 60 cm.

Base – within 40 cm.

On heaving soils, it is necessary to install a cushion made of non-freezing material.

Construction of the foundation

Stages of making a strip reinforced foundation with shallow depth.

1. Marking
2. Development of trenches.

   If the soil does not crumble, trenches are made the width of the foundation. Their walls will act as formwork

3. Filling a 30-centimeter sand and gravel bed in layers, compacting each layer.

   The thickness of each layer is 10 cm

4. Laying waterproofing material on the bottom and walls of the trench
5. Installation of formwork under the above-ground part of the foundation (basement)
6. Installation of fittings
7. Pouring concrete

Foundation quality conditions

To build a quality foundation, the following conditions must be met.

• The correct proportions of components in the concrete mixture
• There should be no air bubbles (voids) in the concrete.

  To achieve this, use a vibrator or bayonet the concrete with a metal rod.

• There should be no interruptions during filling

After pouring, until the concrete hardens, it requires maintenance. It must be protected from the sun and watered in hot weather. Insulate in cold weather.

Rolled waterproofing material is laid on top of the foundation.

The overlap of stripes must be at least 15 cm.

Wall masonry

Before you start building walls, you need to check the horizontalness of the foundation. The permissible height difference is 3 cm.

If necessary, leveling should be done with cement mortar.

The upper plane of the blocks laid in the wall must be horizontal. That is, not only the edges running along the wall must be horizontal, but also those across them.

Horizontal control is carried out using a level. The position of the block is adjusted if necessary with a rubber hammer.

First row

The laying of the first row must be done with extreme precision - the accuracy of the construction of the entire house depends on this.

• Find the highest point of the foundation using a level.

  The first block is laid in the corner closest to this point

• Then blocks are installed in all other corners
• A mooring cord is stretched between the corner blocks along the outer edge of the wall.

  The first row is filled in using it

• If any unevenness in the masonry is formed, they are eliminated with a plane or sanding board. Dirt and dust are removed with a brush

Reinforcement

The reinforcement is laid on foam blocks after filling the first row, and then after laying every fourth row.

A smoothly curved rod is placed in the corners.

• Using a grinder, grooves of 4x4 cm are made at a distance of at least 6 cm from the edge of the block
• The grooves are cleaned of dust and moistened with water.
• Cement mortar is placed in the groove to half the depth
• A rod moistened with water is laid
• The recess is completely filled with solution

A monolithic belt is made at the floor level.

It connects load-bearing walls along the entire perimeter and gives spatial rigidity to the entire structure.

For laying foam blocks the following can be used:

• Cement-sand mortar
• Cement-sand mortar with added lime
• Adhesive for wall blocks

The solution with lime does not set so quickly and has good plasticity.

The glue allows you to make thin seams.

It has a fairly liquid consistency and does not set for a long time.

Block cutting

Usually a row cannot be laid using only whole blocks. You have to supplement it with chopped ones.

You can cut blocks with a hand hacksaw. The cutting line is drawn with a pencil on two adjacent sides to ensure an accurate cut. The cut surface is leveled with a sanding board or plane. A smooth surface is necessary to ensure good adhesion between the solution and the block.

Load-bearing walls

After laying the first row, you need to wait 1-2 hours until the solution sets.

Then the wall masonry continues.

• Corner blocks are laid and leveled
• The mooring is being stretched
• The row is filled with foam blocks
• Irregularities are removed with a plane or sanding board

The ligation sutures should be at least 10 cm.

The minimum length of the outer blocks (corner, opening) is 11.5 cm.

Internal load-bearing walls are connected to external ones by bandaging.

Partitions

1. The junction of the partition is indicated on the load-bearing wall
2. At this point, flexible connections (anchors) made of stainless steel are inserted into the seam. One end is in the load-bearing wall, the other is in the seam of the partition
3. Anchors are secured with nails

Anchors are inserted into the load-bearing wall through a row.

It is allowed not to secure them with nails, but simply press them into the solution.

Door and window openings

You can buy factory-made lintels for ceilings, or they can be made from homemade hollow foam blocks, having a P-shaped cross-section.

1. Mark the locations of the cuts on the foam block
2. Having cut through the grooves, chop off the inner part with a construction hammer
3. Hollow blocks in the shape of an inverted letter U are laid over the opening on wooden supports.

   These can be boards or beams. The supports can be nailed to the side walls of the opening

4. 12-16 mm reinforcement is placed inside the cavity and concrete is poured. The supports remain until the concrete hardens.

You can lay foam blocks over the opening and on metal corners.

Roof

Wooden beams are usually used to construct floors in a foam block house.

The type of roof, its design and shape may vary. Its construction is not much different from this type of work when constructing houses using other building materials.

Exterior decoration

Although foam concrete does not penetrate to a great depth when exposed to moisture, the surface layer absorbs it quite well.

So if the walls are not covered with exterior decoration, they darken and begin to collapse.

The following can be used as exterior finishing for walls made of foam blocks:

• Hinged cladding installed with a gap (siding, decorative panels, house siding with imitation timber)
• Decorative plaster
• Composite panels
• Natural and artificial stone
• Painting with silicone paints

The construction of a country house from foam blocks is relatively inexpensive, and construction occurs quickly.

If you have some construction skills, it is quite possible to make such a house with your own hands.

Video about how to build a house from foam blocks

When building a house on a summer cottage, everyone wants to build one that will be comfortable to live in.

But coziness and comfort depend on the internal layout of the house. First of all.

And the layout itself depends on the size of the building, the number of people in the family, and the presence of small children. It also depends on whether you plan to live in the country only in the summer, or whether you want to come here all year round. There are some things you should definitely consider when deciding how to layout your home.

Layout of a one-story country house

Even a small house should have at least three rooms:

The kitchen can be positioned so that the entrance to the house is through it.

In this case, the kitchen room will also serve as a vestibule, which traps cold air if you come to the dacha in winter.

During cooking, the air in the kitchen heats up noticeably, which is also good for heating the house. This option is much better than building a cramped vestibule.

If you want to make a canopy, you can make it out of glass. Using profiles, double glazed windows and glass doors.

If you use your dacha all year round, you need to provide additional heating.

For example, you can plan a country house with a stove in the kitchen, the back wall of which opens into the next room.

This stove will heat two rooms at once. Well, you can install an electric heater in the bedroom. There are many economical modern models.

It should be taken into account that the house heats up much faster if good quality double-glazed windows are installed on the windows. It should be noted that the warmth in the house does not depend on the size of the windows, but on how well they are glazed. The best option is high-quality plastic windows with several panes.

If a country house made of laminated veneer lumber contains one room and a kitchen, then the living room is divided by a partition.

A bed is installed behind the partition. This house is suitable for a family of two.

If there is one more room in the house, albeit a small one, then it is quite possible to arrange a nursery there.

And the dacha will already accommodate a family of four.

These tips are also suitable for those who already have a small garden house. But many people want to increase the number of rooms and are thinking about building a second floor.

Features of the construction of the second floor

Many people think that a great option for increasing living space would be to arrange a second floor.

But you first need to find out how strong the foundation under the house is. It is likely that it will not be able to support the additional weight. You need to find out about this in advance, and not after cracks begin to appear in the walls and the house begins to collapse.

In addition to this, there are some other features. They must be taken into account before building the second floor.

If there is enough free space on the dacha plot, then it is always better to build a spacious one-story house.

It costs less, and living in a one-story house is more pleasant.

No need to climb stairs. This is especially important if there are elderly people in the house. After all, stairs in two-story dachas are usually steep. They are easier to build than flat ones. In addition, it is much more difficult to heat a two-story house than a one-story house.

If you are building a second floor, there is no need to make concrete floors. It's easier to make them from wood. The house will be warmer. It is best to lift the stairs from the kitchen if it is located immediately outside the front door.

Heat will not escape to the second floor from the living room.

On the second floor there are usually one or two bedrooms. It is best to keep bedrooms small to make them easier to heat. After all, living in a country house, a person enters the bedroom only to sleep.

But, it must be repeated that if the area of ​​the plot allows, then it is better to build a more spacious one-story house instead of the second floor.

Construction of a terrace

Since people spend almost all their time outside in the summer, a covered terrace needs to be added to the house.

It can be located on the entrance side, then the terrace will also play the role of a porch. It needs to be provided with a good roof that will protect it from bad weather and the hot sun. It is also necessary to provide for the fastening of mosquito nets.

Some tips were given on how to make your country house more comfortable.

10 steps on how to build a country house over the summer

If a person plans to build a dacha from scratch, then he can plan it the way his heart desires. But not everything is as simple as it might seem. Below are the most common mistakes that people make when thinking about what kind of house to build on their summer cottage.

Of course, everyone’s tastes differ, but still, we will talk about those things that help reduce construction costs and increase comfort.

Mistakes when planning a country house

The house is too big
There is no need to build a house too big.

Thick walls in the house
Walls that are too thick require a more powerful foundation, and therefore extra costs.

Modern technologies make it possible to build lightweight houses, for example, frame houses, or from timber. Good insulation solves all heating difficulties, and the choice of high-quality material and qualified builders makes the house very durable.

Construction of a basement or ground floor
There is no need to create a large basement or basement floor unnecessarily.

These premises require high-quality waterproofing, insulation, ventilation and heating. For all this you need to hire specialists. Additional costs for building materials are required. Very significant. Also, do not build a base that is too high. This also increases costs.

If you plan to build a fireplace in the house, then you need to build it in the middle so that the heat from it spreads to adjacent rooms.

A fireplace built against an outer wall is completely irrational.

It seems that all things are very simple. But if you avoid these mistakes when planning your house, you can significantly save on building materials and construction time.

Video example of planning a country house using a special program

Posted on: 4-2-2016

For summer residents who are just about to build their first small house, my selection of 15 photos of country house design ideas will be very helpful. I must say, there is something to learn here and something to be surprised by, but what can I say - it’s better to see for yourself!

I draw your attention to the fact that there are no diagrams or plans here.

All material is provided for inspiration only. But, an experienced builder, if you show him a picture of a structure you like, he can easily build, if not exactly the same, then close to the original.

The first house simply captivated me with its canopy with a pointed roof. If it weren’t for this roof shape, it would have been just an ordinary country house! Agree, such a canopy roof, supported by slender wooden columns, gave the whole house sophistication and elegance!

A beautiful country house, to say the least!

And in this miniature house I really liked the turret at the very top. In terms of area, it is like a temporary shed, but the beautiful decoration of the walls, windows, tiles on the roof and this turret make it almost a palace!

By the way, flower boxes mounted under the window greatly improve the appearance of the facade, no matter how small it is!

This house is just very cute, especially the lattice windows and door.

This country house caused a storm of delight among my whole family.

I showed it to them, saying that we would build the same one for ourselves at the dacha. And a miniature terrace, and dormer windows on the roof! Just a peek. A miniature copy of a beautiful country mansion!

There is a lot of light in this house.

Choosing a garden house and its phased construction

because it has very large windows. But even in cloudy weather it is light and gives you a feeling of greater unity with nature! The pediment of this house is designed in an unusual way - it is decorated with two balusters.

And in this house there is a second light under the roof. Since there are no windows on one side, something like dormer windows are made under the roof itself.

True, from the photo it is clear that the owners use it as a workshop, but for newly-minted summer residents it could also serve as a shelter at night and from the rain.

A small wooden house with a canopy across the entire width of the roof.

A good solution - here you have a patio terrace, the wall of the house will protect you from the wind, and the roof canopy will protect you from rain and sun.

This little white house is just a fairy tale!

Elegant, romantic, with a pergola attached to it, it invites you to settle in and not know any grief! Still, white color adds sophistication to any building, even a very small one.

This interesting asymmetrical house has a frame structure and is lined with wood.

The originality of this building lies not only in its unusual roof, but also in the glazing of two walls, forming a “transparent corner” at the exit.

This house is simply attractive and well built.

The blue house under a tiled roof with white curtains looks very attractive.

It feels like the house has a caring owner!

And this bright house in front of a small pond made me feel tender. It is so small and so harmonious with its blue door and windows with tulle curtains that I wanted to sit down in front of it, dip my feet in the pond and daydream for an hour or two.

This house is made of wood, although it is low, it is very nice.

Well, the last house in the series of 15 best is a house with a trapezoidal canopy.

Beautiful, elegant, tastefully decorated - what else can you say! And there is a terrace next to it - there is a place to admire the stars in the evening!

Ideas for small cozy country houses

We could stop here, but there are so many ideas for small houses that I always want to look for something and share my finds with you.

Let me remind you that in America and Canada, the hobby of designing and creating houses on wheels of unusual shapes is very common. These are real residential buildings. I will continue to introduce you to interesting ideas for such houses. After all, if we exclude the wheels, then such houses will look great on our plots! Here is an overview video from the creators of this wonderful house.

There is no translation, but everything is clear.

My construction and life in the country

I would like to tell my story when we decided to live in the country and start all over again. In general, it so happened that our apartments did not exist, and in recent years we lived in rented apartments. And so life within the walls of others and frequent trips brought us - I wanted my own, peace and stability. But the way we live is not rich and can't buy anything, you decide to buy a Dacha (4sotki) and then another, we left the pages very cheap.

These sites are the same, we prepared that they were forced to leave all the bushes and trees from their homes, and yet they had the resources that I introduced sandstone and sand into the future of our home.

But after a few days we decided to give them a chance to defeat the house in the village, and then I brought the plate and two evenings (as I worked during the day), the house was almost ready. It looked like a trailer, but we were not aware of the beauty, it was already the end of September and cold and winter would soon be upon us. Below is a photo of creating a time zone

Construction of a cottage in the country - the beginning

He built it twice - he wanted it faster, but it got dark early, so he took a battery and a lamp with him. So, this house was looking for another night - it was not yet dark.

It worked like a screwdriver and wire, the design was very simple, so everything was done very quickly.

Cabin construction in the country

I then brought in some foam and the house was insulated with 10cm thick foam and foam sealed all the seams between the foam and all the slots.

He made the front door. And the interior, while there were bare slab walls. The next day he brought 200 pieces. red brick and it took two nights to build the brick. A photograph of the furnace design has not survived.

Construction of holiday homes

House dimensions 6.3 * 3m.

interior space 6*2.7, common living room 16.2 square meters, which had to accommodate four adults (me, mom and my two sisters) in the country, electricity, and this is what I thought about in advance. I made a wind generator, I installed a small battery and bought a 12/220 volt converter. The power of such a power plant was very small, because the wind turbine was small and was an irregular dean, also very low. But sometimes one energy-saving light bulb is enough.

All in all, it was a painful start, but a week into this construction, we moved into this period. The transfer took place on October 2, the same day as my sister’s birthday.

In the fall the woods were ready for the winter and a porch was added to the house.

The house is insulated externally with a vapor barrier, covered with film and internal shiny insulation. As a result, in the first winter we found out.

Winter in the country

In winter we were already at home with wind power for every 150 watts, there was enough electricity for lights and sometimes on TV, just as the wind was very weak and there was not enough battery power, but I saved everything for improvement, including the power plant.

I described everything about the plant in the section “My little adventures”,

Therefore, winter lived in such spartan conditions. My sister and I worked, paid in the spring, having accepted a loan 3 years ago, and at the beginning of the summer a new loan appeared, which spent the money on small items and bought a Chinese engine (110ss) to kill a tree, I went to him for a trailer trailer.

We bought a chain saw and two solar panels. up to 100 watts, so they were buying new batteries for the power plant until March.

In the summer, the porch was covered with luminous insulation to keep it cool in the sun, and solar panels were installed on the wall.

Even the lights on the street and in the house repeated the wiring.

Solar panels

In the summer, the wood was prepared for the entire year, and the motorcycle made 35 trips from nearby forest stands.

So I bought corrugated cardboard, wood, cement, and I put a new corrugated panel fence on the front.

Wood collection

At the same time, I poured a concrete pad under the base of the future of our house.

There was no swimming under the foundation, it simply grew and leveled the surface and spilled a 40 cm wide strip around the perimeter of the house.

How to build a house in Dachau: characteristics and construction phases

The thickness of the concrete is 10-15 cm. Below the photo are parts of the concrete. This is how we lived in the fall, photo after the rain, there was a bit of a mess outside as I searched and twisted the jars under the winter potatoes.

Life in the country

Life in the country

In addition, 11 meters were excavated in Dachau, I dug it myself, I was in a hurry for almost a month and poured concrete with concrete, but I finished it.

So, the tile broke through. He dug a basement on the site of the future house, filled the basement with concrete, and then made a hatch into the roof. Small details were done on details, but I will not list all the little things, only the important ones. I wrote about the break here - Well, with my job 2.

Fine

This year, at the beginning of spring, I took 7 plate cubes, bought ruins and cement and started with the main overflow.

The bottom part of the photo is the preparation of the irrigation panels. Last year the center of the concrete base under the furnace was flooded.

Foundation formwork

After installing the panel panels around the perimeter, he reinforced with a 10mm cast in two threads.

Then I invested in concrete and ended up like this.

Filling the foundation

The panel was attached with 6mm hex pins and once ejected it was easy to remove and remove the shell.

Filling the foundation

Then build the wall frame. The dimensions of the house are 6.30 * 10.80 m. The skeleton was placed alone, sometimes the truth helped the sister give or save something. All this has turned him into screws that pull themselves. bottom and top, then he used a homemade galvanized sheet metal plate.

DIY decorated house

DIY decorated house

DIY decorated house

DIY decorated house

Currently, the money for further construction has been completed.

Now you need to make money from corrugated cardboard and place a frame around the roof.

Continuation - second part of the frame

How to build a garden house with your own hands, stages of construction, how to insulate a house, tips on building a foundation, walls and roof. Interior and exterior finishing.

A large number of people, if they don’t already have it, then at least in their minds want their own summer cottage and, of course, to have a garden house built on it. To save on construction, many create small structures with their own hands, but if opportunities allow, it can be built to a more impressive size.

This article will help you create the garden house of your dreams, after reading it you will learn the design features of the garden house, what tools are used for this, how to lay a reliable foundation, the nuances of constructing the frame and the correct execution of the cladding. How to perform high-quality insulation, what a foam coat is and why you need a ventilated façade.

How to correctly create and take into account the design of a garden house, proper space planning, technology for constructing a garden house, the reliability of wall construction, the formation of high-quality floors and ceilings, how to install a roof, the nuances of creating a country house. How much does it cost to build a garden house?
Proper construction of the roof and attic, high-quality interior and exterior finishing of the structure, how to install ceiling joists.

What are economy class houses, revealing the issues of building a panel structure, what materials are best used for this.

Design features

Today, construction technologies offer the construction of garden houses not only from classic materials (logs, cinder blocks, bricks), but also to use plywood sheets, OSB, aerated concrete blocks, foam blocks, timber, etc. as the main building materials.

But it is plywood garden houses that have excellent soundproofing and thermal insulation characteristics, along with ease of work and inexpensive construction costs.

Another advantage of this construction is the opportunity to make a house out of plywood with your own hands. This allows you to significantly reduce the cost of hiring professional teams. But it must be borne in mind that garden houses made of timber and plywood have some disadvantages, for example, the vulnerability of the latter to aggressive actions of the external environment. Accordingly, additional measures must be taken to protect this building material, and this, in turn, increases costs.

Plywood is also an unsafe building material for home residents in terms of penetration by intruders. Therefore, when building a garden house from timber and plywood, external finishing work is required, for example, siding, which, in addition to decoration, also hides the main material used in construction from prying eyes.

Expert opinion

Filimonov Evgeniy

Professional builder. 20 years of experience

Ask a question to an expert

Country houses are built using frame technology, which is gaining increasing popularity in many

Countries of the world.

This is explained by its main advantages:

• there is no need to rent special construction equipment;
• no strong foundation required;
• the country house has excellent energy saving characteristics;
• the ability to quickly complete construction work;
• Due to the lightness of the structure and the materials used during construction, the walls do not shrink.

But the wood that is used to build a house (boards for roof sheathing, bars for wall frames) must be dry, and plywood sheets must have a minimum of chips at the edges. In addition, all wood materials must be additionally treated with special compounds that can provide the required fire safety and also protect against moisture.

The construction of a frame plywood house can be divided into the following stages:

• foundation construction;
• construction of wall frames and plywood cladding;
• roof installation;
• insulation;
• finishing works (internal and external).

The dream of many city dwellers is a beautiful small house outside the city, where they can escape from the hustle and bustle of the city, hide from the heat, and feel the pleasant freshness of the earth under their feet instead of hot asphalt. But not everyone’s dreams come true; it seems that a country house is complicated, expensive, and time-consuming. In fact, building a country house with your own hands is quite simple.

Planning the space

Choosing a location for a future country house is not the time for hasty decisions, because there is not that much space. Thoughtful, competent planning will help you use every piece of land as efficiently as possible. Even though this is your land, you will have to fulfill a number of requirements, maintaining a minimum distance:

• from the street – 5 m
• from the passage – 3 m
• from the neighboring plot - 3 m

We are not considering the option with a low area - water will accumulate there. Optimally, the highest place on the site is in its northern (northwestern) part.

Projects of small country houses

Considering typical designs of country houses, it is easy to notice that the undisputed favorite is a one-story building with an attic. This is a time-tested option for a country house, but you can dispense with the utility unit, because equipment and household supplies can be stored in the attic.

You can add a terrace to the house - in summer it can be used as a dining room. Two-story country houses often obtained without actually constructing a “clean” second floor, having arranged instead attic. Then on the ground floor you can plan a kitchen and living room, and the second floor - for the personal space (bedrooms) of the owners.

Advice! You can save significantly on the heating system - even at the most modest prices for installing a classic one (boiler, pipes and radiators) accounts for 15-20% of the total budget. If you are building a small country house with your own hands, where you plan to live only during the “season” (late spring - early autumn), then to heat it in bad weather, you can get by with electric or infrared heaters.

Prefabricated country houses are becoming very popular - unpretentious, outwardly monotonous parallelepipeds with roof We replaced buildings that were interesting in architectural terms, with an improved layout, one or two floors.

You are buying a kind of construction kit; such a country house can be easily erected with only basic knowledge about construction. The main thing is that it already includes all the systems - electrical wiring, ventilation, air conditioning, plumbing. This will help avoid many mistakes that beginners make when they decide to build a country house with their own hands.

A prefabricated country house is designed for a long holiday with family or friends; it is larger in area, can be one or two floors, with an improved layout. Such a house is equipped with a technical room, a kitchen, rest rooms and a bathroom, equipped with a heating, ventilation, air conditioning system, and supplied with electricity.

The house can be equipped with a water heater, sink, countertop, hanging shelves, shower cabin, necessary plumbing. After installing such a country house, no additional repair work is required; it is completely ready for use.

Laying the foundation

The choice of foundation type is directly related to the choice of material from which the house will be built, as well as the number of storeys. Light houses (from rounded wood, timber, frame houses and modular) can be erected on a columnar or screw foundation; heavy (brick, aerated concrete, stone, concrete blocks) and two-story houses will require the laying of a strip foundation (as an option - a prefabricated one, made of reinforced concrete blocks) along the entire perimeter and under the load-bearing walls of the house.

It is important to know the depth of soil freezing - the foundation should be laid below this level, taking into account the level at which groundwater lies.

In the basement part it is required to install waterproofing at a level of 0.2-0.5 m from the ground. If the soil is dry enough (sand), a cement-sand screed 2-4 cm thick can be used as a screed. For wet soil, roofing material will need to be laid on top of such a screed - in two layers. As an option, roofing felt can be glued onto a dry screed using hot mastic. Waterproofing is installed below the expected level of laying the floor beams.

Advice! In the basement, to ensure ventilation of the subfloor, small holes are made, which are covered with a protective mesh.

A blind area is created around the base, its width is at least 70 cm (it should protrude further than the overhang of the cornice), with a slight slope directed from the walls of the house. To do this, the top layer of earth is removed, clay (sand) is poured, a layer of crushed stone (gravel, broken brick) is poured on top of it and filled with concrete (rolled with asphalt).

Floor and walls

Flooring begins with laying joists. To insulate the floor, insulation is laid between the joists, on top of which a vapor barrier is laid. It is attached to the joists with a stapler, and the joints are taped. Then the subfloor is laid, for which they use an unedged, cheapest board, having previously treated it with an agent against dampness and rot. And only then the finished floor is laid out. In a two-story house, the frame for the floor on the second floor is the ceiling beams of the first.